Summary of the content on the page No. 1
ML507
QuickStart
May 2008
Summary of the content on the page No. 2
Overview • Setup • Boot with ACE-loader ACE File • Observe LCD and Terminal messages • Load new Configuration • Re-load ACE-loader
Summary of the content on the page No. 3
ML507 BSB Hardware • The ML507 PPC440 design hardware includes: – PPC440MC DDR2 Interface – External Memory Controller (EMC) • ZBT SRAM – BRAM – Networking – UART – Interrupt Controller – System ACE CF Interface – GPIO (IIC, LEDs and LCD) – PLB Arbiter Note: Presentation applies to the ML507
Summary of the content on the page No. 4
Additional Setup Details • Refer to ml505_overview_setup document for details on: – Software Requirements – ML507 Board Setup • Equipment and Cables • Software • Network – Terminal Programs • This presentation requires the 9600-8-N-1 Baud terminal setup Note: Presentation applies to the ML507
Summary of the content on the page No. 5
Hardware Setup • Connect the Xilinx Parallel Cable IV (PC4) to the ML507 board • Connect the RS232 null modem cable to the ML507 board Note: Presentation applies to the ML507
Summary of the content on the page No. 6
Hardware Setup • The ML507 uses a DVI video interface • Connect a DVI monitor or • Use a DVI/VGA adapter to connect a VGA monitor – http://www.belkin.com Note: Presentation applies to the ML507
Summary of the content on the page No. 7
Hardware Setup • USB Keyboard – www.dell.com Note: Presentation applies to the ML507
Summary of the content on the page No. 8
Factory CompactFlash • The CompactFlash shipped with the ML507 board has the following ace files preloaded: Note: Presentation applies to the ML507
Summary of the content on the page No. 9
Verify Factory Default Settings • Set the Ethernet PHY jumpers, J22, J23 to positions 1-2 (1) • Insert the Factory CompactFlash into the ML507 board (2) • Set the Front DIP switches (SW3) to 00010101 (1 = ON) (3) • Set the Rear DIP switches (SW6) to 11001010 (4) • Power-up the ML507 board 2 1 4 3 Note: Presentation applies to the ML507
Summary of the content on the page No. 10
Bootload • The bootload_video.ace loads: Note: Presentation applies to the ML507
Summary of the content on the page No. 11
Bootload • The terminal window also reflects the bootload application • Use the left/center/right buttons to choose an application or type a number in the terminal window • After each demo, push the SysACE reset to return to bootload Note: Presentation applies to the ML507
Summary of the content on the page No. 12
Slideshow • Type 1, to launch the slideshow application in Configuration 1 • The slideshow loads the presentation into memory then presents it Note: Presentation applies to the ML507
Summary of the content on the page No. 13
Slideshow • The slideshow app will present a series of slides on the Monitor: Note: Presentation applies to the ML507
Summary of the content on the page No. 14
Web Server • Type 2, to launch the web server application in Configuration 2 – Note: You may need to turn off your browser's proxy and specify a direct connection to the Internet in your browser options Note: Host IP is 192.168.1.1, subnet mask is 255.255.255.0
Summary of the content on the page No. 15
Running the LWIP Demo • Open a web browser to address 192.168.1.10
Summary of the content on the page No. 16
Running the LWIP Demo • Click the Toggle LEDs button; view change on ML507
Summary of the content on the page No. 17
Simon • Type 3, to launch the Simon application in Configuration 3 Note: Presentation applies to the ML507
Summary of the content on the page No. 18
Board Diagnostics • Type 4, to launch the XROM application in Configuration 4 Note: Presentation applies to the ML507
Summary of the content on the page No. 19
Board Diagnostics • XROM includes a series of board test routines Note: Presentation applies to the ML507
Summary of the content on the page No. 20
USB Keyboard • Type 5, to launch the USB Keyboard application in Configuration 5 • Type ML507 and view results: Note: Attach keyboard after demo loads
