Summary of the content on the page No. 1
Using Your GEM-P400 Security System
GEMINI
1 2 3 4
&20387(5,=(’ 6(&85,7< 6<67(0
Oi230a Tuesday, September 16, 1997 08:26
page 1
STATUS
ARMED
Summary of the content on the page No. 2
Oi230a Tuesday, September 16, 1997 08:26 page 2
Summary of the content on the page No. 3
Introduction Congratulations on your purchase of an advanced GEMINI-P400 Security System. Meticulously developed by a leading manufacturer of state-of-the-art security products, this system will provide you with unprecedented peace-of-mind & incorpo- rates some of the most sophisticated features available today. Above all, it has been designed an extra step, to provide all those operating it with very easy, intuitive use. Please carefully review the information contained in this manual,
Summary of the content on the page No. 4
Introduction Table of Contents System Information Keypad Controls and Indicators ................................... 5 Arming your System (When Leaving) ........................... 6 Central Station Phone Number: ____________________ Protecting Yourself While Home .................................. 7 Emergency Keys .......................................................... 8 Central Station Account Number: ____________________ Disarming the System ............................................
Summary of the content on the page No. 5
Keypad Controls and Indicators Trouble Light Zone Lights (1 through 4) will light to indicate will light and the Keypad Press that the corresponding Zone is open, and will sounder will pulse to indicate that a system trou- to bypass all flash to indicate a zone in alarm. ble is present. (See System troubles, Page 11) interior pro- tective de- vices such as motion Status Light will light when all zones are secure sensors, etc. and system is ready to be Armed. GE
Summary of the content on the page No. 6
Arming Your System Arming Your System When Leaving 1 Before arming your system, make sure the green Status light is ON. This indicates that all of your protective zones are secure. If any zones are open, the corresponding Zone number will be lit. Secure these zones before proceeding. If any zones cannot be secured, see Bypassing zones below. 2 Enter your user code and press. The green Status light will go out, the red Armed light will light. • If you make a mistake entering your code
Summary of the content on the page No. 7
y Arming Your System Protecting Yourself While at Home 1 Before arming your system, make sure the green Status light is ON. This indicates that all of your protective zones are secure. If any zones are open, the corresponding zone number will be lit. Secure those zones before proceeding. 2 Enter your User Code and press . The green Status light will go out, and the red Armed light will light. 3 Before your exit delay expires, press to bypass any interior zones, deactivati
Summary of the content on the page No. 8
Emergency Conditions Emergency Buttons The three sets of emergency buttons, if programmed, are always active whether the system is armed + or disarmed. Discuss these Buttons with your installer. The emergency signal will only be activated Auxiliary Emergency when the two respective buttons are pressed at the same time. Enabled? Yes No Auxiliary Alarm: Simultaneously press to alert the central station of an auxiliary emergency, if so programmed. (The nature of
Summary of the content on the page No. 9
Disarming Your System / Silencing an Alarm Disarming Your System when Returning 1 Enter your premises through the Entry/Exit door. The keypad will sound a steady tone to remind you to disarm the system before your Entry Delay time expires. 2 Enter your User Code and press. The red Armed light will go out, indicating that the system has been disarmed. . Note: If you make a mistake entering your code, press and re-enter the code, followed by Alarm Indication If the Red Armed light is
Summary of the content on the page No. 10
Special Functions By pressing A followed by the the appropriate key, (do not press simultaneously) these special functions and features can be enabled: Display System Trouble Easy Arm (when system is disarmed) Pressing followed by when TROUBLE The Easy Arm feature allows the system to be armed by pressing followed by . This will allow the easy is lit will cause the system to display any current system troubles. Pressing will exit the Display System a
Summary of the content on the page No. 11
System Troubles The GEM-P400 is constantly monitoring its own components, as well as all critical services, such as AC power and the telephone line, to insure that it is always ready to provide the protection for which it was designed. When a system trouble does occur, it will caution you by lighting the TROUBLE light and beeping the keypad buzzer. If you cannot immediately clear the system trouble, the system can still be used. Simply press followed by to view the tr
Summary of the content on the page No. 12
System Troubles Keypad Beeps or Zone light System Trouble Action ON Condition Flashes 2 Beeps 3 Wireless Receiver A problem has been detected with the wireless receiver. Trouble Call installing company for service. 2 Beeps 4 Wireless Receiver Jam A problem has been detected with a wireless receiver. Call installing company for service. 3 Beeps 1-4 Wireless Transmitter The battery in a wireless transmitter is low and should be replaced. This transmitter is Low Battery on the zone correspo
Summary of the content on the page No. 13
Programming User Codes Your Installer has assigned a User 1 Code which can be used to not only Arm and Disarm the system, but also to enter the User Program Mode, where you can program other user codes. The following explains how you will use this code to program or erase additional user codes. Entering the User Program Mode Press followed by and enter the User 1 code folowed by. The Armed, Status and lights will flash, and the keypad will beep 4 times. You are now in the User
Summary of the content on the page No. 14
Glossary Ambush Code - In the event that you Central Station - Monitors alarm, Keypad Sounder - A local warning de- are forced by an intruder to disarm your emergency and trouble reports from the vice at the keypad to alert that Entry system, this special code can be used to alarm system and notifies proper authori- delay has started, disarm the system, and simultaneously ties. System Trouble - A problem has been send a silent alarm to Central Station. If Chime - a keypad beep which
Summary of the content on the page No. 15
Notes 15 Oi230a Tuesday, September 16, 1997 08:26 page 15
Summary of the content on the page No. 16
NAPCO LIMITED WARRANTY NAPCO SECURITY SYSTEMS, INC. (NAPCO) warrants its products to be free from manufacturing defects nor authorizes any other person purporting to act on its behalf to modify, to change, or to assume for it, any in materials and workmanship for thirty-six months following the date of manufacture. NAPCO will, within other warranty or liability concerning its products. said period, at its option, repair or replace any product failing to operate correctly without charge to the or
