Summary of the content on the page No. 1
OPERATING GUIDE for your
GEM-DXRP1 KEYPAD
SYSTEM READY
10/01/06 12:09 AM
© NAPCO 2006 OI322 6/06
1
Summary of the content on the page No. 2
INTRODUCTION future reference. Check the Glossary The GEM-DXRP1 is a “smart” user- Regardless of how your system has friendly, interactive menu-driven keypad for an explanation of terms that may be been configured, rest assured that it has designed for your Napco control panel. unfamiliar to you. been carefully designed and engineered Its alphanumeric screen will not only to the highest industry standards. To You'll probably find subjects display the status of your system, but assu
Summary of the content on the page No. 3
TABLE OF CONTENTS TO SILENCE AN ALARM, ENTER YOUR TABLE OF CONTENTS CODE, AND PRESS J. Section Page FOR SERVICE, CALL: _____________________ KEYPAD CONTROLS & INDICATORS ............................................4 CENTRAL STATION: _____________________ SETTING THE ALARM (ARMING) WHEN LEAVING .......................6 EXIT DELAY: ___________________________ PROTECTING YOURSELF WHILE
Summary of the content on the page No. 4
KEYPAD CONTROLS & INDICATORS 2 1 3 7 8 4 5 9 6 10 11 12 4
Summary of the content on the page No. 5
KEYPAD CONTROLS & INDICATORS Window. Displays system status 10 INSTANT Button. (1) Cancels 1 5 BYPASS Button. (1) Deactivates messages, zone descriptions, etc. entry delay on Exit/Entry Zones, selected zones from the system. causing an instant alarm upon (2) Unbypasses a bypassed zone 2 STATUS Light. Lights (green) to violation. (2) Scrolls window (GEM-P3200/9600 panels only). indicate that the system is ready display backward (PRIOR). (3) for arming. If a zone is not 6 RESET Butto
Summary of the content on the page No. 6
SETTING THE ALARM (ARMING) WHEN LEAVING Arming the System SYSTEM READY 1 Check the keypad. The green STATUS light must be on in order to arm. If the green light is off, “ZONES FAULTED” will display in the window followed by the number and description of each faulted zone. Note each problem zone and EXIT TIME 060 secure it by closing a window, door, etc. When all zones are secure, the green PLEASE LEAVE NOW STATUS light will come on and the window will display “SYSTEM R
Summary of the content on the page No. 7
SETTING THE ALARM (ARMING) WHEN LEAVING System Trouble SYSTEM TROUBLE If you attempt to arm with a “SYSTEM TROUBLE” display alternating with an indicated trouble code (e.g. “E02-00” (low battery); see SYSTEM TROUBLE ERROR CODES), a 3-second tone SYS/TRBL will sound at the keypad. The window will display "CAN'T ARM SYSTEM, PRESS RESET KEY". If you cannot correct the problem immediately, pressing C will enable you to arm in this LOW BATTERY condition. Be sure to call for service as
Summary of the content on the page No. 8
PROTECTING YOURSELF WHILE ON THE PREMISES Bypassing Interior Zones BYPASSED SYSTEM READY Interior Zones, when bypassed, allow free movement within the home while the protection of armed perimeter zones is maintained. To bypass Interior Zones, press E and enter your User Code followed by D. Your system may have provisions for two groups of Interior Zones. (Optional) (Interior Groups programmed? YES NO) Press E, followed by D to Bypass Interior Group 1: [ ____________________
Summary of the content on the page No. 9
PROTECTING YOURSELF WHILE ON THE PREMISES Easy Exit (Optional - Easy Exit programmed? YES NO) Your system may have been programmed for Easy Exit, which allows a user to exit the premises while the system is armed. By activating Easy Exit while the system is armed, the Exit Delay countdown will take place, during which time you are permitted to leave through the exit door. The Easy Exit Delay time will be identical to the Exit Delay time the system gives you each time it is arm
Summary of the content on the page No. 10
TURNING OFF THE ALARM (DISARMING) WHEN RETURNING Disarming the System DISARM SYSTEM 1 Enter your premises through the Entry/Exit door. The keypad will sound a steady or pulsing ENTRY TIME XXX tone to remind you to disarm the system before your Entry Delay time expires. 2 Enter your User Code and press D. The red ARMED light will go out, indicating that the system has been disarmed. If you enter an invalid code, the keypad will beep 4 times, INVALID ENTRY signifying an e
Summary of the content on the page No. 11
FIRE PROTECTION (Applicable only where local ordinance permits use of this alarm control panel for fire protection.) Fire-Zone Alarm FIRE FIRE ALARM If a fire is detected, “FIRE ALARM” will be displayed and the keypad sounder will pulse. 1. If a fire is in progress, evacuate the premises immediately! If necessary, call the Fire Department from an outside phone. 2. Press the C button to silence the keypad sounder. 3. If there is no evidence of a fire, enter your User Code an
Summary of the content on the page No. 12
FIRE PROTECTION 2. One person sounds the alarm. against it and open it cautiously. Be Preparing a Fire Escape Plan Even with the most advanced fire alarm 3. Each person tests his door. ready to slam the door if smoke or system, adequate protection requires an 4. Pretend the door is hot and use the heat rushes in. Crawl through smoke, escape plan. alternate escape exit. holding your breath. Close the doors 5. Everyone meets outdoors at the again on leaving to help prevent the To pr
Summary of the content on the page No. 13
FIRE PROTECTION Floorplan Draw a plan of your premises in the space provided below. Floorplan 13
Summary of the content on the page No. 14
FIRE PROTECTION LIMITATIONS OF FIRE ALARM WARNING SYSTEM provide early-enough warning for a variety of who are awake may not hear the warning if Although a fire alarm system may be of a reasons: (a) they may not sense fires that the alarm is obscured by noise from a stereo, reliable and state-of- the-art design, neither it start where smoke cannot reach them, such radio, air conditioner, or other appliance, or nor its peripheral detection devices can offer as in chimneys, walls, roofs, b
Summary of the content on the page No. 15
KEYPAD FUNCTIONS The keypad can provide access to a wide assortment of utility functions. The functions are displayed in a prompting “YES/NO” format. 1 To enter the Function Menu, press A. • In all UL-listed or high-security installations, a valid User Code must first be entered followed by A. 2 To skip a function, answer NO (F) or A. 3 To select and execute a function, answer YES (E) or J. • Functions may be manually scrolled forward or backward using A and B, respectively. •
Summary of the content on the page No. 16
KEYPAD FUNCTIONS Activate Bell Test? Activates the alarm (while disarmed) for about 2 seconds and performs a ACTIVATE battery test. If the alarm does not sound, call for service. BELL TEST Y/N • If the battery is low, a “LOW BATTERY E02-00 SERVICE” will appear in the display indicating a low battery condition. Allow 24 hours for the battery to recharge. If the trouble continues, call for service. Display System Troubles? Displays 1- or 2-digit error code along with a de
Summary of the content on the page No. 17
KEYPAD FUNCTIONS Reset System Trouble? System troubles display and sound at the keypad. Correcting RESET the trouble will clear most indications, however the following error codes will require SYS TRBL Y/N manual reset: E13; E19; E20 and E22. (See SYSTEM TROUBLE ERROR CODES for a description of error codes.) Reset Sensor Watch Failure? (Sensor Watch programmed? YES NO). RESET Your system may have been programmed for Sensor Watch, a feature which SENSOR
Summary of the content on the page No. 18
KEYPAD FUNCTIONS Activate Telephone Test? (Telephone Test programmed? YES NO). Sends a ACTIVATE communicator test to the central station. A communication failure will be indicated DIALER TEST Y/N at the keypad by a system trouble “E03-FAIL TO COMM” display. Repeat the test to attempt to correct a communication failure, as any successful communication will clear this display. Delay Arming 1-4 hours. (Not for UL-listed systems). Your system may be set to TO ARM IN 1-4 HRS
Summary of the content on the page No. 19
KEYPAD FUNCTIONS Activate Program? Activates the Program Mode from Keypad No. 1. Note: This ACTIVATE feature is disabled while armed. (See PROGRAMMING USER CODES) PROGRAM Y/N Activate Download? For installer's use only. If accidentally enabled, press ACTIVATE C to exit. Note: This feature is disabled while armed. DOWNLOAD Y/N Relay Control? (Relay Control programmed? YES NO). RELAY Turns ON or OFF one or more programmed Relay Groups. Pre
Summary of the content on the page No. 20
CENTRAL STATION MONITORING Your alarm specialist may have Opening and/or Closing Reporting. arming (Closing Report), the central programmed your system to be Your system can notify the central station will acknowledge arming. monitored by a central station. The built- station every time it is disarmed or This will signal at the keypad as a in digital communicator can transmit armed. Any or all of up to 96 “ringback” beep. Note: If the emergency signals and status reports to different us
