Summary of the content on the page No. 1
OWNER'S MANUAL
DC-650TS Dust Collector
JET EQUIPMENT & TOOLS, INC. P.O. BOX 1349 Phone:253-351-6000
A WMH Company Auburn, WA 98071-1349 Fax: 1-800-274-6840
www.jettools.com e-mail jet@jettools.com M-708630 08/01
Summary of the content on the page No. 2
This manual has been prepared for the owner and operators of the JET DC-650TS. Its purpose, aside from machine operation, is to promote safety through the use of accepted correct operating and maintenance procedures. Completely read the safety and maintenance instructions before operating or servicing the machine. To obtain maximum life and efficiency from your Dust Collector, and to aid in using the machine safely, read this manual thoroughly and follow instructions carefully. Warranty & Servic
Summary of the content on the page No. 3
WARNING 1. Read and understand the entire contents of this manual before attempting assembly or operation. Do not use this machine until proper training and knowledge has been obtained. 2. Do not leave Dust Collector when plugged in. Unplug from outlet when not in use and before servicing. 3. Do not use outdoors or on wet surfaces. 4. Do not allow to be used as a toy. Close attention is necessary when used near children. 5. Use only as described in this manual. Use only manufacturer’s recommen
Summary of the content on the page No. 4
Grounding Instructions Caution: This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and o
Summary of the content on the page No. 5
230 Volt Operation If 230V, single phase operation is desired, the following instructions must be followed: 1. Disconnect the machine from the power source. 2. This dust collector is supplied with four motor leads that are connected for 115V operation, as shown in Figure A. Reconnect these four motor leads for 230V operation, as shown in Figure B. 3. The 115V attachment plug (A), supplied with the dust collector, must be replaced with a UL/CSA listed plug suitable for 230V operation (D). Contact
Summary of the content on the page No. 6
Specifications: DC-650TS Stock Number................................................................................................................................ 708630 Blower Wheel Diameter........................................................................................................................11” Sound Rating at 3 feet................................................................................................................. 60-70 db Hose Diameter........................
Summary of the content on the page No. 7
material, fittings, construction and grounding. WARNING Stock # JW1050V Read and understand the entire contents of this manual before attempting assembly or operation of the dust collector! Failure to comply may cause serious injury! Unpacking 1. Finish removing all contents from the shipping carton. 2. Report any damage to your distributor. 3. Do not discard any shipping material until after the dust collector has been assembled and is running properly. Contents of the Shipping Carton 1. Plas
Summary of the content on the page No. 8
Assembly WARNING The dust collector must be disconnected from the power source during assembly. Failure to comply may result in serious injury! The JET DC-650TS does not come with a collector can. You can use the JET two stage dust collector on a variety of round, metal and plastic collector cans. The outer diameter of the trash can should be approximately 20-1/4” – 24- 1/4” to fit properly. 1. Attach the deflector (A, Fig. 1) to the plastic cover using two hex cap screws, four flat washers and
Summary of the content on the page No. 9
Electrical Connections WARNING All electrical connections must be done by a qualified electrician. All adjustments or repairs must be done with the dust collector disconnected from the power source, unplugged. Failure to comply may result in serious injury! The DC-650TS dust collector is rated 115V/230V, Prewired 115V. If you want to run the DC-650TS on 230V refer to the wiring diagram found on the inside of the switch box cover (A, Fig. 4). Before hooking up to the power source, make sure that
Summary of the content on the page No. 10
Cleaning the Filter Order the Dust Collection Basics Video which covers topics such as system design, duct CAUTION material, fittings, construction and grounding. Wearing a particle mask/respirator for Stock # JW1050V protection against fine dust particles during cleaning is highly recommended. Clean both the filter and collector can frequently to keep the collector's performance at its optimum. To clean: 1. Disconnect the machine from the power source. 2. Take off the grounding clip and remove
Summary of the content on the page No. 11
Parts Breakdown 11
Summary of the content on the page No. 12
Parts List for the DC-650TS Index Part No. No. Description Size Qty. 1..........331019AW ................... Impeller Housing (upper) ....................... ...............................................1 2..........331019BW ................... Impeller Housing (lower)........................ ...............................................1 3..........MH331001 ................... Motor.....................................................115V/230V, 1HP, 1Ph .............1 ............DC1100-50W
Summary of the content on the page No. 13
Wiring Diagram 13
