Summary of the content on the page No. 1
This Manual is Bookmarked
Operating Instructions and Parts Manual
Dust Collector
Model: DC-1100A/C/RC
DC-1100A/RC DC-1100C/RC
WMH TOOL GROUP
2420 Vantage Drive
Elgin, Illinois 60123 Part No. M-708639
Ph.: 800-274-6848 Revision G 07/04
www.wmhtoolgroup.com Copyright © WMH Tool Group
Summary of the content on the page No. 2
This manual has been prepared for the owner and operators of JET DC-1100 Series Dust Collectors. Its purpose, aside from machine operation, is to promote safety using accepted operating and maintenance procedures. To obtain maximum life and efficiency from your dust collector and to aid in using it safely, please read this manual thoroughly and follow the instructions carefully. Warranty and Service WMH Tool Group warrants every product it sells. If one of our tools needs service or repair,
Summary of the content on the page No. 3
Table of Contents Warranty and Service ...........................................................................................................................................2 Table of Contents..................................................................................................................................................3 Warnings................................................................................................................................................
Summary of the content on the page No. 4
Warnings 1. Read and understand the entire owners manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscured or removed. 4. This dust collector is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a dust co
Summary of the content on the page No. 5
blahblahblah 20. Make your workshop child proof with padlocks, master switches or by removing starter keys. 21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. 22. Do not use the dust collector for anything except wood dust. Materials such as liquids, metal shavings, metal dust, screws, glass, plastic or rock can cause sparks and/or damage when coming into contact with any part of the dus
Summary of the content on the page No. 6
Introduction This manual is provided by JET covering the safe operation and maintenance procedures for model DC-1100 Series Dust Collectors. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide years of trouble free operation if used in accordance to instructions set forth in this manual. If there are any questions or comments, please contac
Summary of the content on the page No. 7
Unpacking DC-1100A/RC Dust Collector 1. Remove all contents from the shipping carton. 2. Report any damage to your distributor. 3. Do not discard any shipping material until after the dust collector has been assembled and is running properly. Contents of the Shipping Carton 1 – Upper Bag Hanger 1 – Base 1 – Housing 1 – Hanger Bracket 1 – Owner's Manual 1 – Hose 1 – Warranty Card 1 – Motor/Fan Assembly 1 – Collector Bag 1 – Filter Bag 2
Summary of the content on the page No. 8
Unpacking DC-1100C/RC Dust Collector 1. Remove all contents from the shipping carton. 2. Report any damage to your distributor. 3. Do not discard any shipping material until after the dust collector has been assembled and is running properly. Contents of the Shipping Carton Canister Filter Box 1 – Canister Filter 1 – Handle 1 – Bag of Hardware for Handles (2) M10 Hex Nuts (2) M10 Flat Washers (1) M10 Lock Washer (4) Knobs DC-1100C/RC 1 – Base 1 – Housing Ba
Summary of the content on the page No. 9
Assembly Base 1. Install four casters to the under side of the base as pictured in Fig. 2. 2. Thread the hex nut (B, Fig. 1) onto the caster shaft. Then slide the lock washer (A, Fig. 1) over the caster shaft. Thread the caster shaft into the threaded hole on the underside of the base, turn until snug. Tighten the nut (B, Fig. 1) against the base with a 14mm wrench. This will give the caster proper clearance. Figure 1 Motor and Fan Assembly 3. Place the base with caste
Summary of the content on the page No. 10
Connector Housing 5. Attach three support brackets (A, Fig. 4) to the base using six M8 x 16 hex cap bolts and six M8 flat washers (B, Fig. 4). Hand-tighten only at this time. Figure 4 6. Install the housing (A, Fig. 5) to two support brackets (B, Fig. 5) using four M8 x 16 hex cap bolts, eight M8 flat washers, and four M8 hex nuts (C, Fig. 5). Be sure hose opening faces fan housing. 7. Before attaching third support bracket place the hanger bracket (D, Fig.5) bet
Summary of the content on the page No. 11
Filter Bag Installation – DC-1100A/RC Referring to Figure 7: 1. Place the hanger (A) on the hanger bracket (B). 2. Slide the filter bag loop (C) over the hanger hook. 3. Thread the retainer strap (D) through the loops on the filter bag (E) and fasten to the collector housing (F). Figure 7 Collector Bag Installation – DC-1100A/RC Referring to Figure 8: 4. Insert the ring of the collector bag (A) at an angle into the housing (B) through the opening at the
Summary of the content on the page No. 12
Collector Bag Installation – DC-1100C/RC 1. Place the ring over the top of the plastic bag and fold over the bag approximately three inches, Figure 9. Figure 9 2. Insert the snap ring (A, Fig. 10) of the collector bag into the bottom of the housing at an angle. 3. Pull down on the ring to make sure it “seats” in the housing. Note: make sure the snap ring “snaps” into place in the housing, and also that the plastic bag hangs down approximately 3” so that there are
Summary of the content on the page No. 13
time will scroll up to 99 minutes, then start again at 00. Release the button when the desired set time is Electrical Connections reached. The dust collector will run for the amount of time displayed on the digital display. If you scroll past All electrical connections must 99 and release the button at 10, for example, the be done by a qualified machine will run for ten minutes, not 110 minutes. electrician. All adjustments or repairs must be done with the dust collector disconnected
Summary of the content on the page No. 14
Cleaning the Filter – DC-1100C/RC Maintenance Never perform maintenance on Never perform maintenance on this machine before turning switch off and this machine before turning switch off and removing plug from power source. Failure to removing plug from power source. Failure to comply may cause serious injury! comply may cause serious injury! Clean both the filter and collector bags frequently to keep the collector's performance at its optimum. Cleaning the Filter Bag – DC-1100A/RC T
Summary of the content on the page No. 15
Parts List – DC-1100A/RC Dust Collector Index No. Part No. Description Size Qty 1............... 411035W ................. Impeller Housing.....................................................................................................1 2............... 411026W ................. Motor Bracket .........................................................................................................1 3............... 998621..................... Strain Relief ...............................
Summary of the content on the page No. 16
Parts Breakdown – DC-1100A/RC Dust Collector 16
Summary of the content on the page No. 17
Filter Assembly for DC-1100C/RC Models Index No. Part No. Description Size Qty 1............... 331050..................... Handle ....................................................................................................................1 2............... TS-1540071............. Hex Nut.................................................................M10 ..........................................2 3............... TS-1550071............. Flat Washer .................................
Summary of the content on the page No. 18
Remote Control Breakdown for DC-1100RC Index No. Part No. Description Size Qty ................. DC1100RC-100....... Receiver Assembly (Items 1-12) ............................................................................1 1............... DCRC-101............... Label.......................................................................................................................1 2............... DCRC-102............... Counter Screw.................................................
Summary of the content on the page No. 19
Wiring Diagram – DC-1100A/C 19
Summary of the content on the page No. 20
Wiring Diagram – DC-1100RC 20
