Summary of the content on the page No. 1
OWNER'S MANUAL
DC-1100C Dust Collector
JET EQUIPMENT & TOOLS, INC. P.O. BOX 1349 Phone:253-351-6000
A WMH Company Auburn, WA 98071-1349 Fax: 1-800-274-6840
www.jettools.com e-mail jet@jettools.com M-708626C 1/02
Summary of the content on the page No. 2
This manual has been prepared for the owner and operators of JET’S DC-1100C. Its purpose, aside from machine operation, is to promote safety through the use of accepted correct operating and maintenance procedures. Completely read the safety and maintenance instructions before operating or servicing the machine. To obtain maximum life and efficiency from your Dust Collector, and to aid in using the machine safely, read this manual thoroughly and follow instructions carefully. Warrant
Summary of the content on the page No. 3
WARNING 1. Read and understand the entire contents of this manual before attempting assembly or operation. Do not use this machine until proper training and knowledge has been obtained. 2. Do not leave Dust Collector when plugged in. Unplug from outlet when not in use and before servicing. 3. Do not use outdoors or on wet surfaces. 4. Do not allow to be used as a toy. Close attention is necessary when used near children. 5. Use only as described in this manual. Use only manufactu
Summary of the content on the page No. 4
Grounding Instructions Caution: This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local co
Summary of the content on the page No. 5
230 Volt Operation If 230V, single phase operation is desired, the following instructions must be followed: 1. Disconnect the machine from the power source. 2. This dust collector is supplied with four motor leads that are connected for 115V operation, as shown in Figure A. Reconnect these four motor leads for 230V operation, as shown in Figure B. 3. The 115V attachment plug supplied with the dust collector must be replaced with a UL/CSA listed plug suitable for 230V operation. Co
Summary of the content on the page No. 6
On-Off Switch Padlock Model No. PB-1, Stock No. 709012 To safeguard your machine from unauthorized operation and to avoid accidental starting by young children, the use of a padlock is highly recommended. JET model PB-1 is available from your local authorized JET distributor or by calling JET Equipment & Tools at 800-274-6848. To lock out an on-off switch: 1. Open the padlock. See Fig. A. 2. Insert through holes in the start button. See Fig. B 3. Close the
Summary of the content on the page No. 7
Specifications: DC-1100C Stock Number..............................................................................................................................708626C Blower Wheel Diameter........................................................................................................................11" Sound Rating at 3 feet................................................................................................................. 70-80 db Hose Diameter....................
Summary of the content on the page No. 8
WARNING Read and understand the entire contents of this manual before attempting assembly or operation of the dust collector! Failure to comply may cause serious injury! Unpacking 1. Remove all contents from the shipping carton. 2. Report any damage to your distributor. 3. Do not discard any shipping material until after the dust collector has been assembled and is running properly. Contents of the Shipping Cartons Canister Filter Box 1. Canister Filter 1. Handl
Summary of the content on the page No. 9
Assembly 1. Install four casters to the under side of the base as pictured in Fig. 1. Thread the hex nut (B, Fig. 1) onto the caster shaft. Then slide the lock washer (A, Fig. 1) over the caster shaft. Thread the caster shaft into the threaded hole on the underside of the base, turn until snug. Tighten the nut (B, Fig. 1) against the base with a 14mm wrench. This will give the caster proper clearance. 2. Place the base with casters on the ground. Attach the motor and
Summary of the content on the page No. 10
4. Attach three support brackets (A, Fig. 4) to the base using six M8 x 16 hex cap bolts and six M8 flat washers (B, Fig. 4). Hand tighten only at this time. 5. Install the housing (A, Fig. 5) to two support brackets using four M8 x 16 hex cap bolts, eight M8 flat washers, and four M8 hex nuts (B, Fig.5). Be sure hose opening faces fan housing. Before attaching third support bracket place the hanger bracket (C, Fig.5) between the support bracket and the
Summary of the content on the page No. 11
7. Place the ring over the top of the plastic bag and fold over the bag approximately three inches, Figure 7. 8. Insert the snap ring (A, Fig. 8) of the collector bag into the bottom of the housing at an angle. 9. Pull down on the ring to make sure it “seats” in the housing. Note: make sure the snap ring “snaps” into place in the housing, and also that the plastic bag hangs down approximately 3” so that there are no air leaks.
Summary of the content on the page No. 12
Electrical Connections Removing the Collector Bag WARNING CAUTION All electrical connections must be done by a Wearing a particle mask/respirator for qualified electrician. All adjustments or protection against fine dust particles during repairs must be done with the dust collector cleaning is highly recommended. disconnected from the power source, unplugged. Failure to comply may result in 1. Disconnect the machine from the power serious injury! source, unplug. The DC-1100C
Summary of the content on the page No. 13
Parts Breakdown for DC-1100C Dust Collector w/Canister Filter 13
Summary of the content on the page No. 14
Parts List for the DC-1100C Dust Collector w/Canister Filter Index Part No. No. Description Size Qty. 1..........708739......................... Filter...................................................... ...............................................1 2..........331052......................... Shaft...................................................... ...............................................1 3..........331012......................... Scraper...............................
Summary of the content on the page No. 15
Index Part No. No. Description Size Qty. 51........TS-1540061 ................. Nut ........................................................M8 ........................................10 52........TS-0561031 ................. Nut ........................................................3/8”-16UNC.............................4 53........TS-1490031................. Hex Head Bolt .......................................M8x20....................................... .1 54........TS-1490011 .....
Summary of the content on the page No. 16
Wiring Diagram 16
