Summary of the content on the page No. 1
Operating Instructions and Parts Manual
Dust Collector
Models: DC-1100BK, DC-1100CK
DC-1100BK DC-1100CK
WALTER MEIER (Manufacturing) Inc.
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-708636
Ph.: 800-274-6848 Revision B 01/2010
www.waltermeier.com Copyright © 2010 Walter Meier (Manufacturing) Inc.
Summary of the content on the page No. 2
Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these Walter Meier Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine ® tools. For the name of an Authorized Service Center in your area call maintenance and major repair on your
Summary of the content on the page No. 3
Table of Contents Warranty and Service .................................................................................................................................2 Table of Contents ......................................................................................................................................3 Warn i n gs ...................................................................................................................................................4 Introductio
Summary of the content on the page No. 4
Warnings 1. Read and understand the entire owner's manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscured or removed. 4. This dust collector is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a dust c
Summary of the content on the page No. 5
20. Make your workshop child proof with padlocks, master switches or by removing starter keys. 21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. 22. Do not use the dust collector for anything except wood dust. Materials such as liquids, metal shavings, metal dust, screws, glass, plastic or rock can cause sparks and/or damage when coming into contact with any part of the dust collector.
Summary of the content on the page No. 6
Introduction This manual is provided by Walter Meier (Manufacturing) Inc., covering the safe operation and maintenance procedures for model DC-1100 Series Dust Collectors. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide years of trouble free operation if used in accordance to instructions set forth in this manual. If there are any quest
Summary of the content on the page No. 7
Unpacking Shipping Content The table below lists the shipping cartons that are Base Unit included with the models of the DC-1100 Dust (SN 708636) Collector. 1 – Housing (A) 1. Locate your particular model and verify that you 2 – Hose Clamps (B) have received the all the correct cartons. 1 – Hose (C) 2. Check contents of each carton against the ship- 1 – Impeller (Motor/Fan Assembly) (D) ping content listings on this and the following 1 – Inlet Port (E) page. 1 – Impeller Cover
Summary of the content on the page No. 8
Canister Filter Kit Bag Filter Kit (SN 708639B) (SN 708636F) 1 – Handle (O) 1 – Upper Bag Hanger (Y) 1 – Canister Filter (P) 1 – Hanger Bracket (Z) 1 – Snap Ring (Q) 1 – Collector Bag (X) 5 – Collector Bags (R) 1 – Filter Bag (W) 1 – Canister Filter Hardware Bag (SN DC1100-CHP) 1 – Retainer Strap (AA) Contains: (2) M10 Hex Nuts (S) (2) M10 Flat Washers (T) (1) M10 Lock Washer (U) (4) Knobs (V) Filter Bag Kit Contents Canister Filter Kit Contents C
Summary of the content on the page No. 9
Base Unit Assembly Base 1. Install four casters to the underside of the base as pictured in Fig. 2. Referring to Figure 1: 2. Thread the hex nut (B) onto the caster shaft. Then slide the lock washer (A) over the caster shaft. Thread the caster shaft into the threaded hole on the underside of the base, turn until snug. Tighten the nut (B) against the base with a 14mm wrench. This will give the caster proper clearance. Figure 1 Motor and Fan Assembly Referring to Figure 2:
Summary of the content on the page No. 10
Connector Housing 5. Attach three support legs (A, Fig. 4) to the base using six M8 x 16 hex cap bolts and six M8 flat washers (B, Fig. 4). Hand-tighten only at this time. Figure 4 6. Install the housing (A, Fig. 5) to two support legs (B, Fig. 5) using four M8 x 16 hex cap bolts, eight M8 flat washers, and four M8 hex nuts (C, Fig. 5). Be sure hose opening faces fan housing. Note: For model DC-1100BK only – Before attaching third support bracket place the ha
Summary of the content on the page No. 11
Filter Bag Kit Assembly If you purchased DC-1100BK Dust Collector, this section describes the assembly and installation of the contents of the Filter Bag Kit (SN 708636F). Filter Bag Installation Referring to Figure 7: 1. Place the hanger (A) on the hanger bracket (B). 2. Slide the filter bag loop (C) over the hanger hook. 3. Feed the retainer strap (D) through the loops on the filter bag (E) and fasten to the collector housing (F). Figure 7 Collector Ba
Summary of the content on the page No. 12
Canister Kit Assembly If you purchased Model DC-1100CK Dust Collector, this section describes the assembly and installation of the contents of the Canister Kit (SN 708639B). Canister Filter 1. Mount the handle onto the canister filter with two M10 hex nuts, two M10 flat washers, and a M10 lock washer (Figure 9). 2. Mount the canister filter on top of the collector housing (A, Fig. 5) and tighten the knobs on the canister filter (Figure 9). Figure 9 Collector Bag 3. Plac
Summary of the content on the page No. 13
Electrical Connections Dust Collector RF Remote All electrical connections must Power Control (Optional) be done by a qualified electri- The DC-RC Remote Power Control (Figure 1) should cian. All adjustments or repairs must be done be used for activating Dust Collection units powered with the dust collector disconnected from the by 115V only up to 1-1/2HP. The DC-RC Remote power source, unplugged. Failure to comply may Power Control unit is rated at 115V, Single Phase result in serio
Summary of the content on the page No. 14
Changing Operating Frequency Installing the DC-RC Remote Power Control (Optional Accessory) If several devices are controlled by the same type remote control unit, each remote control unit can be The DC-RC Remote Power Control unit can be set to operate at its' own unique operating frequency placed anywhere for convenience and portability if as follows: used to control other machines or it can be mounted as a permanent part of a machine, such as the DC- Referring to Figure 14: 1100 Dust
Summary of the content on the page No. 15
Cleaning the Filter – DC-1100CK Maintenance Never perform maintenance on this machine before turning switch off and Never perform maintenance on removing plug from power source. Failure to this machine before turning switch off and comply may cause serious injury! removing plug from power source. Failure to comply may cause serious injury! Clean both the filter and collector bags frequently to keep the collector's performance at its optimum. Cleaning the Filter Bag – DC-1100BK To cl
Summary of the content on the page No. 16
Parts Parts List – DC-1100A Dust Collector Index No. Part No. Description Size Qty 1 .............. 411035W ................Impeller Housing............................................................................................. 1 2 .............. 411026W ................Motor Bracket ................................................................................................. 1 3 .............. 998621....................Strain Relief ...............................................
Summary of the content on the page No. 17
Parts Breakdown – DC-1100A Dust Collector 17
Summary of the content on the page No. 18
Canister Filter Assembly Index No. Part No. Description Size Qty 1 .............. 331050....................Handle ........................................................................................................... 1 2 .............. TS-1540071 ............Hex Nut............................................................M10 ....................................... 2 3 .............. TS-1550071 ............Flat Washer......................................................M10 .........
Summary of the content on the page No. 19
Filter Bag Assembly Index No. Part No. Description Size Qty 1 .............. 708698....................Filter Bag ........................................................30 Micron ............................... 1 2 .............. AB410012 ...............Retainer Strap ................................................................................................ 1 3 .............. 708699A .................Collection Bag ....................................................................
Summary of the content on the page No. 20
Wiring Diagram – DC-1100A 20
