Tote Vision LCD-703HD user manual

Summary of the content on the page No. 1

LCD-703HD Series


High Definition


7.0” TFT LCD Monitor





















Model : LCD-703HD (Stand Alone)














Model: LCD-703HD2 (19” Rack Mount unit)

www.totevision.com

Summary of the content on the page No. 2

The LCD-703HD Series features our completely Digital million pixel TFT LCD high resolution screen, excellent color reproduction. Analog signals are digitized using an advanced 10 bit process with 4x over sampling and adaptive 5 line comb filter plus exacting color space conversion. Video is scaled to fit on screen in the highest resolution using a state of the art Triple gate technology LCD panel that incorporates with precision Gamma correction to product the best images available.

Summary of the content on the page No. 3

Display (Viewing Area) 7" (6.0" × 3.6") Resolution (Pixels) 800 H × RGB × 480 V Dot Pitch 0.1905mm × 0.1905mm Brightness (in cd/m²) 350 cd/m² System NTSC/PAL auto recognition 1 Composite, 1 Component HD/SD in/OUT, Inputs S-Video IN/OUT , DVI Dimensions 6.85"W × 5.24"H × 1.38"D Approx. Weight 0.7 Kgs(with Remote excluding packing) Power Consumption DC 12V 400 mA (run @ 5-20 VDC) 1. Overview The LCD-703HD Series represents a state of art LCD display technology in broadcast and p

Summary of the content on the page No. 4

5 Electrical Specifications Display (Viewing Area) 7” (6.0”H × 3.6”V) (152.4mm x 91.44mm) Viewing Angles 130°H x 120°V Resolution (RGB Dots) 800H x RGB x 480V (1.2 million pixels) Contrast Ratio 300:1 Gamma 2.2 Luma Linearity Typical +/- 3% with 5 ire increments (0 to 10 ire) Dot Pitch 0.1905mm H x 0.1905mm V Pixel Response 22ms average Screen Refresh Rate 50/60 Frames per second Backlight Type / Life LED / 20,000 to 30,000 Hours Typical Brightness 350 cd/m² System NTSC/PAL auto re

Summary of the content on the page No. 5

7 LCD Panel Cleaning When cleaning the LCD Panel it is very important to use non-abrasive and ammonia free cleaning agents and a clean micro fiber clothe, or cheese clothe. Do not use paper towels. Paper towel fibers are coarse and may scratch the surface of the LCD screen. Paper towels may also leave streaks on the surface. Antistatic and fingerprint resistant cleaning agents are recommended. Operational Setup 1. Unpack the LCD-703HD and accompanying remote control. Physicall

Summary of the content on the page No. 6

Composite Video IN/OUT DC INPUT *RS-232 S-Video TALLY In IN/OUT DVI INPUT Component IN/OUTPUT * 9pin D-Sub Connector pin assignment RS-232 /TALLY pin configuration 5 4 3 2 1 RS-232 GND NC T/X R/X NC 9 8 7 6 TALLY GND Green RED Yellow TALLY SYSTEM - The tally system on the LCD-703HD is accessed via the DB-09 connector on the back of the unit labeled ‘RS-232/TALLY’. The system works by closing the contacts between the ground pin

Summary of the content on the page No. 7

Applicable signal format Signals Frames per Second Aspect Active Scanning Input Raito Lines Method 30/29.97 4:3/16:9 Interlaced CVBS, Y/C,YPrPb 525-60i 483 4:3/16:9 Interlaced CVBS, Y/C,YPrPb 480i 60/59.94/50 483 25 4:3/16:9 Interlaced CVBS, Y/C,YPrPb 625-50i 576 60/59.94/50/30/29.97 16:9 483 Progressive YPrPb,DVI 480P /25/24/23.976 60/59.94/50/30/29.97 16:9 Progressive 720P 720 YPrPb,DVI /25/24/23.976 16:9 Interlaced 1035i 60/59.94 1080 YPrPb,DVI 16:9 Interlaced 1080i 60/59

Summary of the content on the page No. 8

Model numbers of LCD-703HD Series LCD-703HD LCD-703HDL LCD-703HDX LCD-703HDL back LCD-703HD1 (single unit) LCD-703HD2 (two units)