Summary of the content on the page No. 1
Summary of the content on the page No. 2
FlexPhones Master Installation and Operation Manual Table of Contents Section Title Page # Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Who to Contact for Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Product Description . . . . . . . . . . . . . . . .
Summary of the content on the page No. 3
FlexPhones Master Installation and Operation Manual INTRODUCTION CAUTION! Thank you for your purchase of a Broadcast Tools® FlexPhones Master multi-user Broadcast Tools® headphone system (referred to as the FlexPhones Master or Master throughout this Products, as with any manual). We’re confident that this product will give you many years of dependable electronic device, can service. This manual is intended to give you all the information needed to install and fail without warning. operate the
Summary of the content on the page No. 4
Summary of the content on the page No. 5
FlexPhones Master Installation and Operation Manual Installation: Please examine your FlexPhones Master and/or AHR-1 carefully for any damage that may have been sustained during shipping. If any is noted, please noti- fy the shipper immediately and retain the packaging for inspection by the shipper. The package should contain the FlexPhones Master, 16vac@600ma wall power transformer, two CAT5 cables and this manual. Installation of the FlexPhones Master in high RF environments should be perform
Summary of the content on the page No. 6
FlexPhones Master Installation and Operation Manual DIM jumper configuration Removing either or both of the Dim jumpers mutes the program audio dur- ing a talkback session, while inserting either or both will dim the program audio approximately 20db below normal program levels. Use the table below along with the jumper layout sheet in the appendix to properly configure. Factory defaults have these jumpers installed. Right ear talkback enable jumper: In a talkback session, talkback audio is alw
Summary of the content on the page No. 7
FlexPhones Master Installation and Operation Manual Cable Interconnection After completion of the jumper set-up and the audio connections have been made, connection of the CAT5 cable can be started. Connect the user supplied CAT5 cable between the desired channels (follow the numbers on the chassis) rear panel RJ45 on the FlexPhones Master and each AHR-1 and/or MSI. Up to two AHR-1’s or one AHR-1 and one MSI can be daisy-chained from each RJ45 on the Master. Program Level Setup Turn the rea
Summary of the content on the page No. 8
FlexPhones Master Installation and Operation Manual Operation: To call any combination of AHR-1’s press the desired front panel talkback button(s) or the ALL CALL button. You may also do the same using user supplied momentary normally open dry contact switches connected across each of the rear panel remote control inputs. The Front panel headphone jacks and level control only monitor program. Only one set of headphones should be used. NOTE: The talkback feature may be added by reconfiguring i
Summary of the content on the page No. 9
FlexPhones Master Installation and Operation Manual Specifications: Program Input Level -15 to +4 dBu. MIL+24dBu, balanced, bridging 10k Ω. Talkback Input Level -60 to -30 dBu MIC / -15 to +4dBu LINE, balanced. Microphone phantom power +15vdc. Gain 6 dB. Frequency Response 10 to 20 kHz; +/- .0.25dB Signal/Noise Ratio >85 dB nominal, weighted 10 to 22Khz. Distortion 0.005% THD, nominal. IMD (250/7kHz) 0.005% IMD, nominal. Headphone Output 24 to 600 W headphones. 200mw nominal. Switching Method
Summary of the content on the page No. 10
Product_Name Installation and Operation Manual L LIIM MIIT TE ED D W WA AR RR RA AN NT TY Y The term “Buyer” as used in this document refers to and includes both (but only) (a) any person or entity who acquires such an item for the purpose of resale to others (i.e., a dealer or distributor of an item), and (b) the first person or entity who acquires such an item for such person’s or entity’s own use. Broadcast Tools warrants to each Buyer of any item manufactured by Broadcast Tools that the it
Summary of the content on the page No. 11
FlexPhones Master Installation and Operation Manual FlexPhones Master Six Channel Headphone System with Independent Talkback APPENDIX Functional Diagram Local HP Amp – LT PGM + 1/4” CHANNEL 1 1/8” DIM LT 1 – 2 RT PGM + DIM RT RJ-45 to AHR-1*, 3 Active Headphone 4 – Front Panel XLR, T/B + Remote or MSI*, 6 RT T/B 5 Monitor System Enable Rear Panel Plug-In Mic/Line Ext – 7 PWR Interface T/B CMOS Analog Switching Ext + 8 Euroblock Screw Terminals RMT CHANNEL 2 RJ-45 T/B (same as Channel 1) RMT CHA
Summary of the content on the page No. 12
Summary of the content on the page No. 13
Summary of the content on the page No. 14
Summary of the content on the page No. 15
Summary of the content on the page No. 16
Summary of the content on the page No. 17
Summary of the content on the page No. 18
