Summary of the content on the page No. 1
LIMITED LIFETIME WARRANTY
Products manufactured and sold by OMEGA RESEARCH & DEVELOPMENT, INC. (the Company),
are warranted to be free from defects in materials and workmanship under normal use. If a product
OPERATING & INSTALLATION
sold by the Company proves to be defective, the Company will repair or replace it free of charge within
the first year and thereafter all parts to be repaired will be free with only a nominal charge for Omega
Research and Development, Inc.'s labor and return shippi
Summary of the content on the page No. 2
Contents 2 27 Operation Guide Introduction & Safety Considerations .......................................................................... 3 To Activate Remote Start .......................................................................................... 4-5 Deactivating Remote Start ........................................................................................... 5 Valet Mode ........................................................................................................
Summary of the content on the page No. 3
prevents accidental starter grind should the key be turned while the remote starter is Introduction 26 3 in operation. Additionally, the Orange wire also provides the vehicle immobilizing Congratulations for choosing the Modular Advanced Remote Starter and Security feature for the Anti-Carjacking operation. Connection instructions are included with op- System, and enjoy the luxury of starting your vehicle's engine from the comfort of your tional starter interrupt socket and relay. home or
Summary of the content on the page No. 4
diagrams. The correct wire will show 12 Volts only when the headlight switch is in 4 25 To Activate Remote Start: the "Parking Light" and "Head Light" positions. This wire can usually be found at the headlight switch, and various other locations within the vehicle, such as the rear body MARS-10 MARS-11 : harness or firewall connector. Press the necessary button or Press the blue “START” Caution: When such a wire is located, be sure to also test that it is n
Summary of the content on the page No. 5
existing keyless entry or alarm system to activate the remote start operation. If the 24 When you leave your vehicle, simply set the climate controls for what you would 5 Pink/Black wire receives a Negative pulse, the MARS unit will start the vehicle's like to have operating upon remote starting - the heater, defroster or air conditioning. engine, provided that all safety circuits are in the proper status. After the engine has been Upon entering the vehicle place the ignition key in the switch
Summary of the content on the page No. 6
Once the MARS is in Valet Mode, an attempt to remote start will instead be ac- factory alarm system. Connect the Yellow/Green wire to the wire in the vehicle 6 23 knowledged by the parking lights turning on, then flashing rapidly, then 3 slow which is connected to one of the doorlock key cylinders. The typical OEM alarm flashes, but no engine starting attempt will occur. has an electrical switch in the key cylinders which switches -Ground when the key unlocks the door. This wire can usually b
Summary of the content on the page No. 7
1) Connect the Black/Yellow wire to the vehicle's tach wire, which is found in the 4) Within 15 seconds press the next transmitter’s button. 22 7 engine compartment, although in many cases it may also be located inside the ve- The Status Light turns off and the parking lights flash once. hicle. To use a multimeter to verify the correct tach wire, set it for AC Volts scale. The Repeat this action for each remaining transmitter. correct wire will read 1 to 6 volts AC at idle, and will incre
Summary of the content on the page No. 8
20-Gauge Black/Yellow Wire: Engine Detect Input 8 21 Installation The Black/Yellow wire is the engine detect wire. The Connection Required. It is highly recommended that this system be professionally installed, as the sophistication MARS unit utilizes two different methods of monitoring the vehicle during the remote start- of the modern automobile and the complexity of this type of product installation is often ing process. Consider both methods before selecting one to use, and then co
Summary of the content on the page No. 9
How to program features: 18-Gauge 20 Black Wire: System Ground 9 1) Turn the ignition key “On”, then “Off”. Connection Required. Connect the Black wire to a very good, clean chassis ground. A recommended connection is to an existing machine-thread bolt, either in the 2) Within 7 seconds press the Valet Switch 5 times. driver's kick panel, steering column area or a major structural member behind the dash. The Status Light will flash twice, then turn off . Small dash
Summary of the content on the page No. 10
Blue Wire Exiting Programming Mode: To Additional 22 Gauge Blue Wire: 10 19 Optional Starter Circuit Simply allow the MARS to time out of Features Programming Mode by not perform- 500mA ( - ) Ignition Output 30 Relay ing any programming actions for 15 seconds; or, turn the ignition “On” to immediately Connection If Needed. exit the programming mode. 85 86 This 22 gauge Blue wire is a 87a The MARS indicates its exit from Features Programming Mode with 2 short and 1 500mA Negative ou
Summary of the content on the page No. 11
# • Feature 3 is “Single or Double Pulse Activation”. The “Double Pulse” Jumper 18 Programming the Yellow/Green Wire 11 option allows the MARS-10, in certain vehicles, to activate remote starting by operation: Locate and open the small access panel locking the vehicle doors two times with the original keyless entry transmitter. Exact on the top of the control module case. Place the operations and vehicle suitability varies; consult with the installer for specific details. Jumper as shown o
Summary of the content on the page No. 12
the 3-pin Red port to energize the second Starter wire. Installation Instructions 12 17 Note: If a security system is present which utilizes a starter interrupt circuit, After reading this manual, start the installation by affixing the WARN- the Green wire must be connected to the Starter Motor side of the interrupt. ING DECAL to a visible area in the engine compartment! 12-Gauge Yellow Wire: Ignition Output Do not attempt to install this Remote Car Starter into a manual transmiss
Summary of the content on the page No. 13
mined which control module wires will be used. Most installers will list these MARS-11 Receiver Module: 16 13 wires, then "map out" the installation by locating and noting the target wires in The MARS has a plug-in window mount Receiver Module. Optimum performance the vehicle. This will also determine the best location for the MARS control module, is obtained by mounting this module high and unobstructed on the vehicle’s glass, such as which is mounted upon completion of the installation. the
Summary of the content on the page No. 14
30 Amp 30 Amp Black/Yellow: 14 15 Receiver (Tach Wire) (Smart Start) Tach Smart WIRING DIAGRAM Hood Pin ? Switch Unit To Coil To Battery + Wire Start Adjust MARS-11 ONLY Adjust Starter Yellow/Green: Orange: (-) Output When Adjustment OEM Disarm Activated LED Valet OPTIONAL Blue: Yellow/Red: Relay For Switch Yellow/Green: (-) OEM Arm Anti-Grind Status Programmable Hood Light Output Switch Ignition Smart Start Red/Black: Switch SMART START / Green: SWITCH TACH WIRE Bra
