Summary of the content on the page No. 1
©2008 Pella Corporation
Part Number: 80JJ0103
INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION
FOR CLAD HINGED PATIO DOOR WITH ADJUSTABLE HINGES
PARA LA PUERTA PARA PATIO REVESTIDA, CON BISAGRAS ADJUSTABLES
®
Always read the Pella Limited Warranty before purchasing or installing Pella products. By
installing this product, you are acknowledging that this Limited Warranty is part of the terms of the
sale. Failure to comply with all Pella installatio
Summary of the content on the page No. 2
YOU WILL NEED TO SUPPLY: TOOLS REQUIRED: ® ™ SmartFlash foil backed butyl window and door flashing tape or equivalent ™ Window and Door Insulating Foam Sealant by the Dow Chemical Company or equivalent low pressure polyurethane window and door foam - DO REMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT. 1 ROUGH OPENING PREPARATION A. Verify the opening is plumb and level. Note: It is critical that the bottom is level. B. Ve
Summary of the content on the page No. 3
E. Apply sill flashing tape #1. Cut a piece of flashing tape 12" longer than the opening width. Apply at the bottom of the Note: The tape is cut 12" longer than the width so that it will extend 6" up each side of the opening. F. Tab the sill flashing tape and fold. Cut 1" wide tabs at each Apply sill flashing tape #2. Cut a piece of flashing tape 12" longer In-swing doors: piece of flashing tape. The flashing tape should come to within 1" of the interior fa
Summary of the content on the page No. 4
E. Plumb and square door. Place shims at each hinge and lock strike location between the door and the sides of the opening. bottom of the door to square it in the opening. Make sure that the panels are even across the bottom. Note: On center latch double doors the lock strike will not be shimmed since it is located in the center of the unit. DO NOT over shim. F. Check the interior reveal. Make sure the measurement from the interior face of the door to the interior face of
Summary of the content on the page No. 5
L. Check door operation. Open and close the door to check for proper operation. Make sure the door will latch correctly. Note: If there are any problems with the operation, recheck and adjust the reveal. M. Adjust the reveal if needed. The door panels have adjustable hinge increase the space between the hinge side of the frame and the door panel, or counter clockwise to increase the space between the door panel and the lock side of the frame. DO NOT turn the screws more than a 3/4 tu
Summary of the content on the page No. 6
B. Apply top flashing tape. Cut a piece of flashing tape long least 1" past the side flashing tape on both sides. Apply the tape 1/2" onto the frame cladding, over the top Note: The top flashing tape must overlap the side flashing tape to prevent water from getting behind it. C. Fold down top flap D. Apply flashing tape to diagonal cuts. Cut pieces of flashing tape at least 1" longer than the diagonal cuts in the water resistive barrier. Apply the tape covering the entire diag
Summary of the content on the page No. 7
5 SEALING THE DOOR TO THE EXTERIOR WALL CLADDING When applying siding, brick veneer or other exterior finish material, leave adequate space between the door frame and the material for sealant. Refer to the illustration that corresponds to your finish material. Note: The sealant details shown are standard recommendations from the sealant industry. Contact your sealant supplier for recommendations and instructions for these and any other applications.
Summary of the content on the page No. 8
INTERIOR FINISHING Remove sanding dust. Limited Warranty. sash edges. Note: To maintain proper product performance do not paint, finish or remove the weather- stripping, mohair dust pads, gaskets or vinyl parts. Air and water leakage will result if these parts are removed. After finishing, allow venting windows and doors to dry completely before closing them. cleaning chemicals will cause adverse reactions with window and doo
