Summary of the content on the page No. 1
©2011 Pella Corporation Part Number: 818K0100
INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION
WOOD HINGED PATIO DOOR – (INCLUDES – STANDARD,
PERFORMANCE UPGRADE AND HURRICANESHEILD® IMPACT
RESISTANT IN-SWING, OUT-SWING)
Instrucciones enspañol en el reverso.
Important Safety Information:
® ®
Pella HurricaneShield Products have been tested in accordance with the large missile impact
testing requirements have been certifi ed to meet those requirements. Check with the individual
(building
Summary of the content on the page No. 2
SEALANT SEALANT The performance of any building is dependent upon the design, installation, and workmanship of the entire building system. Pella Corporation strongly recommends consulting an experienced architect, contractor, or structural engineer prior to installation of Pella products. The individual (building owner, architect, contractor, installer and/or consumer) responsible for the project must take into account local conditions, building codes, inherent component limitations, the ef
Summary of the content on the page No. 3
1" 6" Interior Interior Exterior 1 ROUGH OPENING PREPARATION A. Confi rm the opening is plumb and level. Note: It is critical that the bottom is level. 1A B. Confi rm the door will fi t the opening. Measure all four sides of the opening to make sure it is 3/4" larger than the door in width and 1/2" larger in height. Measure the width at the top, bottom, and center. Measure the height at the far left side, the far right side, and in the center. Note: 1-1/2" or more of solid wood blocking i
Summary of the content on the page No. 4
Install flush against exterior rough opening. Weather Barrier EXTERIOR SILL PAN LIP EXTERIOR SILL PAN LIP Flashing Tape EXTERIOR SILL PAN LIP INTERIOR SILL PAN LIP 1" 1" Variable 1" 1" Exterior EXTERIOR SILL PAN LIP INTERIOR SILL PAN LIP Optional Sill Pan Instructions. I. Cut the sill pan to the width of the rough opening plus 2". Note: The 2" added onto the rough opening width is for a 1" bend on each end. J. Make a 1" cut in each fold at both ends of the sill pan. Note: These cuts w
Summary of the content on the page No. 5
EXTERIOR SILL PAN LIP INTERIOR SILL PAN LIP T. Attach the aluminum sill support or wood blocking to the exterior of the box plate to 1P 1T support the edge of the door sill. Place the sill support fl ush with the subfl oor. 2 PREPARE THE DOOR FOR INSTALLATION TWO OR MORE PEOPLE WILL BE REQUIRED TO HANDLE THE PANEL AND FRAME SAFELY. A. Remove plastic wrap and cardboard packaging from door. Do not remove plastic shipping spacers. The shipping spacers will help keep the door square during in
Summary of the content on the page No. 6
EXTERIOR SILL PAN LIP INTERIOR SILL PAN LIP 1st Bead 2nd Bead Leave a 2" break in center of pan 3rd Bead #6 x 5/8” corrosion B. Doors using Installation Clips: resistant screws Install installation clips. Place each clip so the lip is facing up and against 6“ from end the brickmould at the locations shown in the placement diagram. Secure each clip by driving a #6 Lip x 5/8" corrosion resistant screw through each of the outer two holes of the three holes shown. 2B Note: If cl
Summary of the content on the page No. 7
1 INCHES 23 mm 20 30 40 50 60 70 Exterior Interior 3D D. Plumb and square door. Place shims at each hinge and lock strike location between the door and the sides of the opening. Keep shims back 1/2" from interior face of the door frame. Insert shims in other locations as needed starting up 6" from the bottom of the door to square it in the opening. Make sure that the reveal around the door(s) is equal. On double doors, make sure that panels are even across the bottom. Note: On center l
Summary of the content on the page No. 8
Interior Interior of sealant into the three sill strike holes and install the three # 8 x 3" fl at head stainless steel screws (provided) into the holes. K. Shim between the frame and the rough opening at the head strike location and at every frame anchor hole location. Remove and replace head strike screws with three #8 x 3" corrosion resistant screws (provided) through the head strike, door 3K 3K frame, shims and into the rough opening. Note: For doors with no head strike check head
Summary of the content on the page No. 9
N. For Doors with adjustable hinges: The hinges can be used to move the panel side to side by moving all hinges in the same direction or the hinges can slightly rotate the panel by adjusting the hinges in opposite directions. Use a T20 Torx wrench to turn the center screw clockwise (+) to increase the space between the hinge side of the frame and door panel. Turn the center screws counter-clockwise (-) to decrease the space between the hinge side of the frame and the door panel . Note: Do n
Summary of the content on the page No. 10
INSTALL THE PERFORMANCE UPGRADE 5 OR HURRICANESHIELD FASTENERS In-Swing Frame Screw Method: 6" 16" MAX O.C. 6" 6" 16" MAX O.C. 6" 5A Note: If installing with installation clips, proceed to Step E. A. Jambs: Clearance Clearance Out-swing: On the room side of the jamb; Hole Hole Location Location drill and counter-sink 13/64" deep diameter clearance holes through the door frame only and not into the rough opening in the locations shown. (See Out-Swing diagram in lower right). Clearance Cl
Summary of the content on the page No. 11
D. Secure the jambs and head of the door. Drive #10 x 3-1/2" corrosion resistant wood screws through the door frame and shim, into the rough framing. Drive the screws until snug but DO NOT over-tighten the screws. DO NOT bend or bow the unit frame. #10 x 3-1/2" corrosion resistant wood screw 5D Drill 1/8” diameter pilot Out-Swing 5C holes through the clearance hole in the frame. E. Drill 13/64" clearance holes through the threshold but not into the rough opening, at the locations shown in H
Summary of the content on the page No. 12
6" Interior 6 INTERIOR SEAL Caution: Ensure use of low pressure polyurethane window and door insulating foams and strictly follow the foam manufacturer’s recommendations for application. Use of high pressure foams or improper application of the foam may cause the door frame to bow and hinder operation. A. Add a sealant bead across the inner sill and 6" up each jamb between the frame and rough opening. Note: If needed, fi rst place backer rod between frame jamb and opening 6" up each jamb. 6
Summary of the content on the page No. 13
A. Insert backer rod into the space around the door so there is at least a 1/2" clearance between the backer rod and the exterior face of the wall cladding and the brickmould or wood trim. Note: Backer rod adds shape and depth for the sealant line. B. Apply a bead of sealant to the entire perimeter of the door. At each end of the bottom of the 7A door, insert sealant into the spaces between the bottom of door and the sill support and connect it to the perimeter sealant. C. Shape, tool a
Summary of the content on the page No. 14
CARE AND MAINTENANCE Care and maintenance information is available in the Pella Owner’s Manual. You can obtain an owner’s manual by contacting your local Pella retailer. This information is also available at www.pella.com. IMPORTANT NOTICE Because all construction must anticipate some water infi ltration, it is important that the wall system be designed and constructed to properly manage moisture. Pella Corporation is not responsible for claims or damages caused by anticipated and unanticipa
Summary of the content on the page No. 15
This page left blank intentionally.
Summary of the content on the page No. 16
This page left blank intentionally.
