Руководство по эксплуатации Kuppersbusch USA GMS 955.1

Краткое содержание страницы № 1

Gas Cooktop
Installation, User and Service Instructions



GMS 955.1

Краткое содержание страницы № 2

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR’S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. OBSERVE ALL FEDERAL, STATE AND LOCAL CODES AND ORDINANCES WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing Property damage, personal injury or death. Do not store or use gasoline or other flammable vapors and liquid in the vicinity of this or any other appliance WHAT TO DO IF YOU SMELL GAS 1.

Краткое содержание страницы № 3

Gas Installation Requirements This appliance shall be installed by an authorized person and installed in accordance to The manufactures installation instructions. IMPORTANT: This Appliance must be installed in strict Compliance with all Federal, State and Local laws (Where applicable) In the absence of local codes, the installation must conform to American National Standards, National Fuel Gas Code ANSI Z223.1 – Latest edition ** or B149.1 If local code permits, a flexible metal a

Краткое содержание страницы № 4

Dimensions and Distances requirements Cabinet overhead and side clearances The minimum overhead clearances shall be in accordance with the minimum values indicated in Fig. 1 for square angle cuts and Fig. 2 for rounded cuts. Fig. 1 Fig. 2 * * * * Minimum Clearances * Refer to Fig 3 for Cooktop clearance dimensions Inches Millimeters ” L2 1 9/16 40

Краткое содержание страницы № 5

Overall and Cutout Dimensions Below are the required cutout dimensions and the overall dimensions of the cooktop as indicated in Fig. 4 Fig. 4 Overall Cutout Inches Millimeters Inches Millimeters W 33 7/8” 860 W 33 1/16” 840 D 19 11/16” 500 D 18 7/8” 480 Gas tubing and electrical location Fig

Краткое содержание страницы № 6

Install the Cooktop into the cabinet. Install the supplied hold down brackets (A) to the underside of the Cooktop using the supplied Phillips head screws (B) as shown in Fig. 6. Slide the hooks into position and secure the cooktop to the countertop. Trim any exposed gasket seal. Fig. 6 Gas Connection Check the ‘gas type’ sticker attached to the Cooktop. Details of the injector sizes used are recorded on the data plate located on the base of the Coo

Краткое содержание страницы № 7

Electrical Connection WARNING! This appliance is equipped with a three-prong grounding plug for your protection against shock hazard and should be plugged directly into a properly grounded receptacle. Do not cut or remove the grounding prong from the plug. Please refer to Fig. 5 0n page 5 for the location of the electrical wall plug. This unit requires a 15 amp polarized and grounded wall outlet. Failure to proper polarize the outlet may cause erratic discharges from the burner sp

Краткое содержание страницы № 8

By-pass jet adjustment for low flame setting 1) Turn the right front burner on to ignite. Once lit, turn to the lowest setting (small flame). 2) Remove the knob from the cooktop and place in a secured location. Locate the adjustment screw shown in Fig. 8 in the center of the burner valve shaft. Fig. 8 Increase Decrease Larger Flame Smaller Flame 3) Using a small flat blade screwdriver, locate and adjust the screw to obtain a proper flame he

Краткое содержание страницы № 9

User instructions WARNING! Keep the appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquids. Do not store dangerous or flammable material in the cabinet areas above the appliance. Store all flammable materials In a safe lace to avoid potential hazards. For safe use of appliances, do not use this unit as a source of space heating. Do not use aerosol sprays in the vicinity of the appliance while it is in operation. Operati

Краткое содержание страницы № 10

Maintenance - Never use an abrasive cleaner - Before cleaning the appliance it is available that the unit should be disconnected from the power supply. - Cleaning the work surface periodically. Clean the burner heads, the enameled steel pan supports and the burner caps using warn water and a mild detergent. Avoid using steel wool for the fibers of the pad could affect the electronic igniters. - Any spillage must always be removed as soon as possible using a rag or damp cloth. If the gas