Краткое содержание страницы № 1
Gas Hob
IZGS 68 ICTX
EG
Краткое содержание страницы № 2
Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances. Please read this user manual carefully and keep it throughout the product life cycle as a reference document. The user manual should be passed on to any future owner of the appliance. 2
Краткое содержание страницы № 3
Contents For the User Important Safety Information ............................................................................. 4 Description of the appliance .............................................................................. 6 Operation .......................................................................................................... 7 Using the hob .................................................................................................... 8 Cleaning and Maintenanc
Краткое содержание страницы № 4
English Important safety information This warnings has been given for the safety of you and others. We therefore ask you to carefully read the procedures of installing and using this cooker. Installation contact with it and keep them far enough from the heated parts of this The work of installation must be appliance. carried out by competent and qualified installers according to the regulations • If the appliance is out of order, in force. disconnect it from the electric supply. • Any modifica
Краткое содержание страницы № 5
appliance. A poor air supply could Environmental Information cause lack of oxygen. After installation, please dispose of • Ensure that the gas supply complies the packaging with due regard to with the gas type stated on the safety and the environment. identification label, placed near the gas supply pipe. • When disposing of an old appliance, • This appliance is not connected to a make it unusable, by cutting off the combustion products evacuation cable. device. It must be installed and connec
Краткое содержание страницы № 6
Description of the appliance 2 2 3 1 4 1 Auxiliary burner 2 Semi-rapid burner 3 Triple crown burner 4 Control knobs 6
Краткое содержание страницы № 7
the "off" position and wait for Operation at least 1 minute before trying to light the burner again. Hob burner control knobs To switch off burners The symbols on the knobs mean: = no gas supply To put the flame out, turn the knob to the symbol ( ). = maximum gas supply Take care when frying food in hot oil or fat, as the overheated = minimum gas supply splashes could easily ignite. When switching on the mains, after For easier lighting, proceed before installation or a powe
Краткое содержание страницы № 8
Using the hob correctly Practical hints The burners To ensure maximum burner • If the control knobs become difficult to turn, please contact your local Service efficiency, you should only use pots and Force Centre. pans with a flat bottom fitting the size of the burner used. • As soon as a liquid starts boiling, turn down the flame so that it will barely Triple Crown Burner keep the liquid simmering. diameter 18-26 cm Front Semi-rapid Burner diameter 12-18 cm Rear Semi-rapid Burner diameter 12-2
Краткое содержание страницы № 9
Cleaning and Mainteinance Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. This appliance cannot be cleaned with steam or with a steam cleaning machine. The burners The burner caps and crowns can be removed for cleaning. Wash the burners taps and crowns YES using hot soapy water, and remove marks with a mild paste cleane
Краткое содержание страницы № 10
The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little wasing up liquid has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for non-stick saucepans; - steel wool pads; - bath/sink stain removers. Should the hob top become heavily soiled, the following products are recommended: - For stainless steel hobs use a proprietary stainless steel cleaner. - For other hobs use Hob Brite
Краткое содержание страницы № 11
Technical data Cut out dimensions Heat Input (see chapter “Building In”) Triple Crown burner 4,0 kW Width: 560 mm Semi-rapid burner 2,0 kW Depth: 480 mm Auxiliary burner 1,0 kW Overall dimensions Electric supply: 230 V ~ 50 Hz Width: 594 mm Category: II2H3+ Depth: 510 mm Gas supply: LPG 28-30 / 37 mbar Appliance class 3 BURNER NORMAL REDUCED NORMAL POWER POWER POWER kW kW NATURAL POWER LPG 28-30/37 mbar 3 m /h g/h inj. inj. G20 G30 G31 100/mm 20 mbar 100/mm Auxiliary 1,0 0,33 70 0,095 50 73 7
Краткое содержание страницы № 12
Installation The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force. The appliance must be electrically disconnected before all interventions. If any electric supply to the appliance is required to carry out the work, ensure all the necessary precautions are followed. The side walls of the unit in which the hob is going to be installed, must not exceed the height of the working top. Avoid install
Краткое содержание страницы № 13
Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper. The connection should be suitable for connecting to RC 1/2 (1/2 BSP male thread). Important When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Use some soapy water, never a flame. Ensure that the main connection pipe A) End of shaft with nut does not exert any strain on the hob. B) Washer It is important to i
Краткое содержание страницы № 14
A. Injectors replacement • Ensure that the gas taps are in the 'OFF' position • Isolate the hob from the electrical supply • Remove all pan supports, burner caps, rings, crowns and control knobs. • With the aid of a 7mm box spanner the burner injectors can then be unscrewed and replaced by the appropriate Natuaral gas injectors (Fig.1). B. Adjustment of minimum Fig. 1 level When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the p
Краткое содержание страницы № 15
Electrical Connection The appliance is designed to be connected to 230 V monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in force. Before the appliance is connected: 1) check that the main fuse and the domestic installation can support the load (see the rating label); 2) check that the power supply is properly earthed in compliance with the current rules; 3) check the socket or the double pole switch used for the electrical connection
Краткое содержание страницы № 16
Remplacement of the voltage cable The connection of the voltage cable to the appliance's terminal block is of Neutral type "Y". This means that its replacement requires the specific equipment of a technician. In this case, Earth Fig. 3-a (yellow/green)) only cable type H05V2V2-F T90 must be used. The cable section must be suitable to the voltage and the working temperature. The yellow/green earth wire must be approximately 2 cm longer than the phase wires (Fig. 3-a). To open the terminal block a
Краткое содержание страницы № 17
594 Building In SR SR TC A Fig. 4 Dimensions are given in millimeters A = Auxiliary burner SR= Semi-rapid burner TC= Triple Crown burner These hobs can be inserted in a built-in kitchen unit whose depth is between 550 and 600 mm. The hobs dimensions are shown in Fig. 4; the cut out dimensions are shown in Fig. 5. The edge of the cut out must have a minimum distance from the rear wall of 55 mm. If there are side walls, or sides of the furniture unit near the hob, the cut out edges must have a min
Краткое содержание страницы № 18
Then, place them at 11 mm from the side edges and at 10 mm from the rear edge, as shown in Fig. 6, taking care that the seals meet without overlapping. 2. Place the hob in the cut out, taking care that it is centred. 3. Fix the hob with the relevant fixing clamps, supplied with the injectors Fig. 6 kit (see diagram). When the screws have been tightened, the excess seal can be removed. a The edge of the hob forms a double seal which prevents the ingress of liquids. Fig.7 a) seal Possibilities for
Краткое содержание страницы № 19
Kitchen unit with oven The hob recess dimensions must comply the indication given in Figs. 9 and 10 and must be provided with brackets to allow a continuous supply of air. The hob's electric connection and the oven's one must be carried out separately, both for safety reasons and to allow the oven to be easily taken off the unit. Wall units or extractor hoods must be Fig. 9 at least 650 mm from the cooktop (Fig. 5). Service and original spare parts This machine, before leaving the factory, has b
Краткое содержание страницы № 20
3971350.01 05/09 R.A
