Краткое содержание страницы № 1
INSTALLATION INSTRUCTIONS
Gas-on-glass cooktop
CG302D, CG451D, CG603D, CG604D,
CG752D, CG903D & CG905D
models
NZ AU
590149D 02.13
Краткое содержание страницы № 2
2 1 SAFETY AND WARNINGS Do not use or store flammable materials on or near this appliance. WARNING! Do not spray aerosols in the vicinity of this appliance while it is in operation. Packing elements (eg plastic bags, polystyrene foam, staples, packing straps etc) and tools should not Electrical shock hazard be left around during and after installation, especially if they are within easy reach of children, as these Before carrying out any work on the electrical section of the applian
Краткое содержание страницы № 3
3 2 PARTS SUPPLIED 1 Dual Wok Pan support Pan support Small pan support (1) Wok stand (1) Fibre washer (1) Elbow / “ BSP Mini wok Pan 2 (Models with a Dual Wok only) (not supplied with support (1) (some models only) external thread (1) Dual Wok only models) (CG604D only) Clamping LPG test point NG regulator (1) brackets (4) adaptor (1) (NG models and screws (4) (LPG models only) only) Installing multiple products Note: if installing multiple products adjacent to each other within the same cut
Краткое содержание страницы № 4
4 3 GAS RATE SUMMARY-MODELS SEMI-RAPID SEMI-RAPID DUAL WOK DUAL WOK AUX SEMI-RAPID CG302D CG451D CG603D SEMI-RAPID SEMI-RAPID DUAL WOK DUAL WOK MINI WOK AUX CG604D CG752D SEMI-RAPID SEMI-RAPID DUAL WOK SEMI-RAPID DUAL WOK DUAL WOK RAPID AUX CG903D CG905D
Краткое содержание страницы № 5
5 3 GAS RATE SUMMARY All appliances are factory set for Natural gas or LPG and are not convertible. Check the appliance data label. CG302D CG451D CG603D BURNER AUX SEMI-RAPID DUAL WOK SEMI-RAPID DUAL WOK Nominal Nominal Nominal Nominal Nominal Jet size Jet size Jet size Jet size Jet size rating rating rating rating rating (mm) (mm) (mm) (mm) (mm) (MJ/h) (MJ/h) (MJ/h) (MJ/h) (MJ/h) GAS TYPE 1.43 1.26 NG (1.00 kPa)* 1.00 5.0 1.35 8.8 1.43 21.0 1.30 8.4 1.26 16.6 0.70 0.70 0.80 0
Краткое содержание страницы № 6
CG905D CG903D CG752D CG604D CG603D CG451D CG302D 6 4 PRODUCT & CABINETRY DIMENSIONS G B C H I TOP TOP Note: Gas inlet connection is located in the rear right corner. A J K D F FRONT E REAR SIDE Product and cabinetry dimensions (mm) overall height of product (excluding burners, dials and pan supports) 64 64 64 64 64 64 64 A B overall width of product 300 450 600 600 750 900 900 C overall depth of product 530 530 530 530 450 450 530 height of chassis (below top of bench) 59 59 59 59 59 59 59 D E
Краткое содержание страницы № 7
CG905D CG903D CG752D CG604D CG603D CG451D CG302D 7 5 CLEARANCE DIMENSIONS I E D C F A G B H ISO FRONT Clearance dimensions (mm) minimum clearance from left edge of cutout to nearest combustible surface 120 60 115 130 115 115 130 A B minimum clearance from right edge of cutout to nearest combustible surface 120 60 115 115 115 115 115 minimum clearance from rear edge of cutout to: C nearest combustible surface 160 85 160 160 125 125 160 nearest non-combustible surface 45 45 45 45 45 45 45 minim
Краткое содержание страницы № 8
CG905D CG903D CG752D CG604D CG603D CG451D CG302D 8 6 FLUSH MOUNTING INSTALLATION (NOT RECOMMENDED) G G B WARNING! We do not recommend flush mounting and sealing as servicing requires the cooktop to be removed from the benchtop. The owner carries all risk for flush mounting the cooktop. The owner must ensure the cooktop has been cut out from the benchtop before servicing can C HH be carried out. Fisher & Paykel will not be liable for any costs associated with removing or
Краткое содержание страницы № 9
9 6 FLUSH MOUNTING INSTALLATION (NOT RECOMMENDED) 6a 6b 6c ROUTER THE BENCHTOP TO THE FIT THE CLAMPING BRACKETS MASK OFF THE AREA TO BE SPECIFIED DEPTH SILICONED x 4 1 view from below 2 3 Choose most appropriate slot for benchtop 5 mm 16 - 50mm 6d 6e APPLY SILICONE WIPE OFF EXCESS SILICONE 6f IF REMOVING PRODUCT, CUT AROUND THE SILICONE TO REMOVE PRODUCT 2 O min. 150 C rated 1 Ensure silicone does not leak underneath glass.
Краткое содержание страницы № 10
10 7 8 DISCARD PACKAGING REMOVE THE TWO TRANSIT SCREWS Recycle responsibly Repeat on the other side 9 FIT THE ELBOW AND WASHER 10 LOWER GENTLY INTO THE CUTOUT Fibre washer Elbow (1/2” BSP external thread) Floating nut
Краткое содержание страницы № 11
11 11 12 FIT CLAMPING BRACKETS BASED ON THE SECURE TO BENCHTOP BENCHTOP THICKNESS x 4 view from below x 4 16-20mm 20-30mm 30-40mm 40mm+ Repeat on all the other sides 13 14 CONNECT TO GAS SUPPLY CHECK ALL CONNECTIONS FOR GAS LEAKS NG Models LPG Models Make sure to fit the supplied Make sure to fit the supplied GAS regulator. test point adaptor. GAS Adjust to obtain a test point Make sure the supply pressure pressure of 1 kPa with all is regulated to 2.75 kPa, with all Arrow burners operating
Краткое содержание страницы № 12
12 16 15 AFFIX DUPLICATE DATA LABEL SOMEWHERE FIT PAN SUPPORTS ACCESSIBLE & PLUG COOKTOP IN Ensure the pan supports are located securely and in the correct orientation (refer to User guide) Duplicate data label 17 TEST OPERATION To check that the ignition system operates correctly, light each burner by itself, then all burners in combination. Check for a well‐defined blue flame without any yellow tipping. If any abnormality is evident, check that the components of the burner assembly are
Краткое содержание страницы № 13
13 18 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Installer’s name: Have you installed the clamping brackets? Installer’s signature: Have you verified that the type of model (factory-set for NG or LPG) Installation company: matches the type of gas at the site of installation? Date of installation: Have you used the fibre washer supplied? Have you leak-tested all connections? LEAVE THESE INSTRUCTIONS WITH THE CUSTOMER Is the appliance set to the correct working pressure? Important!
Краткое содержание страницы № 14
Краткое содержание страницы № 15
Краткое содержание страницы № 16
