Краткое содержание страницы № 1
Installation Instructions
®
Epicure Range
For Use with Models: ER30D, ER30D-C, ER30DSR
SAVE THESE INSTRUCTIONS
THIS APPLIANCE HAS BEEN TESTED IN ACCORDANCE WITH THE LATEST EDITION OF
ANSI Z21.1 STANDARD FOR HOUSEHOLD GAS APPLIANCES.
Part No. 102187 Rev. C
Краткое содержание страницы № 2
All specifications subject to change without notice. Dacor assumes no liability for changes to specifications. © 2007 Dacor, all rights reserved.
Краткое содержание страницы № 3
Table of Contents Important Safety Instructions ..................................................1-3 Installation Instructions ..........................................................8-20 Customer Service Information ....................................................3 Preparing for Installation ........................................................8-12 Planning the Installation ...........................................................4-8 Electrical Connection ...........................
Краткое содержание страницы № 4
Important Safety Instructions To reduce the risk of fire, explosion, electric shock, serious injury or death when installing or using this appliance, follow basic safety precautions, including the following: WARNING 1. Read the accompanying use and care manual before operating this appliance. 2. Keep packaging materials away from children. Plastic sheets and bags can cause suffocation. 3. If you receive a damaged product, immediately contact your dealer or builder. Do not install or use a dam
Краткое содержание страницы № 5
Important Safety Instructions WARNING 27. Turn the knobs to the “OFF” position prior to removing them from the valve stems. 28. The cooktop should never be operated without the knobs and trim rings in place. 29. For your safety, do not use the oven to cook without the convection filter(s) installed. When the filter is not installed, the spinning fan blades at the back of the oven are exposed. 30. Non-stick coatings, when heated, can be harmful to birds. Remove birds to a separate, well-ventil
Краткое содержание страницы № 6
Planning the Installation WARNING Electrical Requirements - IMPORTANT: Observe all governing codes and ordinances Freestanding Units for Use in Canada during planning and installation. Contact your local building department for further information. • It is the owner’s responsibility to ensure that the required 4 wire electrical outlet is installed by a licensed electrician as specified below prior to range installation. The electrical Electrical Requirements outlet installation, including
Краткое содержание страницы № 7
Planning the Installation Product Dimensions All tolerances: +1/16”, -0 (+1.6 mm, -0) Back of Range GAS - ELECTRICAL ACCESS DIMENSIONS Gas Inlet A B C D E Range electrical access, cover removed 4 7/8” 21 3/4” 8 5/8” 10 3/16” 7/8”* (124 mm) (552 mm) (219 mm) (259 mm) (22 mm) * When using an appliance cord, the hole size must be increased B to 1 1/8” by removing the conduit bracket inside the range electrical access box. D Electrical connection E A hole in bottom C Gas and Electrical Dimens
Краткое содержание страницы № 8
Planning the Installation Product Dimensions (continued) All tolerances: +1/16”, -0 (+1.6 mm, -0) 45 9/16” (1157mm) 28 1/8” (714mm) 26 5/8” (676mm) 25 5/8” (651mm) 23 9/16” (598mm) Rear of Front Panel 23” (584mm) to Back of Chassis 37 7/8” (962mm) to 35 3/4” (908mm) Model ER30DSR with Standard Trim 46 1/16” (1170mm) 28 5/8” (727mm) 27 1/8” (689mm) 26 1/8” (663mm) 24 1/16” (611mm) Rear of Front Panel 23” (584mm) to Back of Chassis 37 7/8” (962mm) to 35 3/4” (908mm) Model ER30DSR with Optional E
Краткое содержание страницы № 9
Planning the Installation Cabinet Layout • All dimensions shown are based on standard American • Carefully check the location where the range is to be cabinets, 36 inches (914 mm) high at the finished countertop installed. For best performance, the range should be placed by 24 inches (610 mm) deep, with a 25 inch (635 mm) overall away from drafts that may be caused by doors, windows and countertop depth. When installing the range into non-standard heating and air conditioning outlets. cab
Краткое содержание страницы № 10
Planning the Installation 10” Min. 10” Min. Non-Combustible 7/16” 1/4” Min. (254mm) (254mm) Rear Wall (11mm) Rear Wall (6mm) Both Sides Both Sides 2 13/16” (71mm) 27 7/8” (708mm) ERV Opening 29 1/4” (743mm) Countertop 29 1/4” (743mm) 23 9/16” Opening Countertop (598mm) 24 1/16” Opening 30 1/16” (764mm) (611mm) Cabinet 30 1/16” (764mm) Opening Cabinet Opening Combustible Side Combustible Side Wall Above Range Wall Above Range 1” (25mm) 1” Minimum Cabinet depth: 27 1/8” (688mm) (25mm) Minumum Co
Краткое содержание страницы № 11
Installation Instructions Level and Adjust the Range Height Changing the Backguard (Models ER30D and 1. Raise or lower the range until it is the same height as the ER30D-C) counter-top. To adjust the height, turn the foot on the bottom Models ER30D and ER30D-C come standard with a 3” backguard of each leg as shown below. installed. The 6” and 9” backguards are optional. 2. Use a level to make sure that the range does not tilt front to To change the backguard: back or side to side. Readjust
Краткое содержание страницы № 12
Installation Instructions 2. Close the door. Remove and retain the two screws from the Installing the ERV Trim Kit (Model ER30DSR) back of the kick panel as shown below. Pull the kick panel To install a raised vent with self-rimming model ER30DSR, you free from the front of the unit. must install the optional ERV trim kit. To change the trim on model ER30DSR: 1. Remove and retain the seven (7) chrome screws that hold the existing trim pieces in place. 2. Slide the existing trim pieces off t
Краткое содержание страницы № 13
Installation Instructions 9. With the door closed, reattach the kick panel to the range 3 Inch Side Panel Kit Installation for Model by snapping the ball studs on the back of the panel into the ER30DSR (continued) holes on the front panel of the range. Locate the center mounting hole. Remove and retain the screw attached to the chassis beneath it. 5. Insert the tabs on the trim piece into the slots on the range. 6. Use the hex head screw (83023) removed from the side, a Torx head screw re
Краткое содержание страницы № 14
Installation Installation Instructions Instructions Removing the Oven Door Electrical Connection WARNING WARNING • Do not attempt to disengage the hinge catches with the • Wire the range only in compliance with local ordinances. door removed from the oven. The hinge springs could • Do not turn on power to the range until instructed to release causing personal injury. do so in the Verify Proper Operation section of these • Do not lift or carry the oven door by the door handle. instructions.
Краткое содержание страницы № 15
Installation Instructions Installation Instructions Connecting the Wiring to the Range Refer to the range rating label (see page 3) for power requirements. L1 Terminal There are four possible ways to wire the range: • 4 Wire Conduit Neutral Terminal • 3 Wire Conduit (where local codes permit) Jumper Link • 4 Wire Appliance Cord (where local codes permit) • 3 Wire Appliance Cord (where local codes permit) L2 Terminal The sections below and on the following pages give directions for connecting e
Краткое содержание страницы № 16
Installation Instructions Electrical Connection (cont.) Connecting the Conduit to the House Connection to Junction Electrical Junction Box power supply Box WARNING • Do not ground the appliance to a gas supply pipe or hot water pipe. • Do not turn on power to the appliance until the range is permanently grounded. • A grounded cold water pipe must have metal continuity to Wire Nut, electrical ground and must not be interrupted by insulating 3 Places materials. Any insulating materials mus
Краткое содержание страницы № 17
Installation Instructions Junction Box Connection to Separate No. 10 (minimum power supply copper grounding wire Fasten clamp tightly on pipe Wire Nut, 4 Places Connection to appliance (Page 13) 4 Wire Connection Conduit Junction Box Connection with External Ground Meter No. 4 copper wire Metal Water Pipe Clamps Bare metal Insulated Pipe Jumper
Краткое содержание страницы № 18
Installation Instructions Electrical Connection (cont.) Appliance Wire Connections - Where Local Code Permits 5. Slide the end of the appliance cord into the strain relief from WARNING the bottom of the box Do not connect the green appliance wire to the neutral (white) 6. Connect the white (neutral) wire to the neutral terminal in the supply wire unless local building codes permit. box. 1. Remove the range electrical access cover from the back of 7. Connect the L1 wire to the L1 power supp
Краткое содержание страницы № 19
Installation Instructions Gas Supply Connection WARNING • Make sure the gas supply valve is off and that the power to the range is turned off at the circuit breaker or fuse box Bare Wire prior to connecting the gas line. Connections • Do not apply excessive pressure when tightening gas connections and fittings. • Do not use Teflon tape or plumber’s putty on gas flex line connections. • Check for gas leaks as instructed below before using the appliance. Do not use a flame to check for leak
Краткое содержание страницы № 20
Installation Instructions Final Installation 1. Peel the protective plastic coating off of the range, including the range door. 2. Adjust the range legs to the desired height. 3. Carefully slide the range into position in the cutout. The rear anti-tip leg should engage the anti-tip bracket. Re-installing the Oven Door(s) WARNING To avoid personal injury or damage to the door from it falling off its hinges: • Make sure that the notch on the bottom of each hinge rests on top of the lower lip
