Краткое содержание страницы № 1
OWNER’S MANUAL
Thank you for purchasing the Roland Bi-Amp Monitor DS-30A.
201b
Before using this unit, carefully read the sections entitled: “IMPORTANT SAFETY
INSTRUCTIONS” (p. 3), “USING THE UNIT SAFELY” (p. 4), and “IMPORTANT NOTES”
(p. 5). These sections provide important information concerning the proper operation
of the unit. Additionally, in order to feel assured that you have gained a good grasp of
every feature provided by your new unit, Owner’s manual should be re
Краткое содержание страницы № 2
For EU Countries This product complies with the requirements of European Directives EMC 89/336/EEC and LVD 73/23/EEC. For the USA FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can
Краткое содержание страницы № 3
IMPORTANT SAFETY INSTRUCTIONS The lightning flash with arrowhead symbol, within an CAUTION equilateral triangle, is intended to alert the user to the RISK OF ELECTRIC SHOCK presence of uninsulated “dangerous voltage” within the DO NOT OPEN product’s enclosure that may be of sufficient magnitude to ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR constitute a risk of electric shock to persons. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, The exclamation point within an equilateral tr
Краткое содержание страницы № 4
USING THE UNIT SAFELY The symbol alerts the user to important instructions Used for instructions intended to alert or warnings.The specific meaning of the symbol is the user to the risk of death or severe determined by the design contained within the injury should the unit be used triangle. In the case of the symbol at left, it is used for improperly. general cautions, warnings, or alerts to danger. Used
Краткое содержание страницы № 5
IMPORTANT NOTES 291b In addition to the items listed under “IMPORTANT SAFETY INSTRUCTIONS” and “USING THE UNIT SAFELY” on page 3 and 4, please read and observe the following: add 1 Power Supply • During operation, this unit must be placed at a distance of no less 301 than 20 cm from any walls. • Do not use this unit on the same power circuit with any device that add 2 will generate line noise (such as an electric motor or variable li
Краткое содержание страницы № 6
Panel Descriptions Front fig. Power Indicator HF Driver Lights when power is on. * Do not touch the diaphragm. Digital In Indicator LF Driver * Do not touch the speaker cone. This lights up when output is received from a connected digital device or during standby. Connect the digital-signal output device, set the "Input Select switch" to DIGITAL INPUT, and set Bass-reflex Ducts the "Digital Input select switch" according to the These are conduits connector to which the de
Краткое содержание страницы № 7
Panel Descriptions Digital Input Select Switch 5 Level Control This switch selects Optical or Coaxial. Select the connector This adjusts the input level. Turning the control clockwise used for the input signal. increases the sound from the speakers. Assign Switch 6 HF Trim Control This switch selects the stereo position of the digital signal. It selects Right, L+R, or Left when using two DS-30A This adjusts the sound quality of the treble range monitors for ste
Краткое содержание страницы № 8
Connection Examples Using Two DS-30A Monitors for Stereo Sound fig. Example for Example for Using Analog Input Connectors Using Digital Input Connectors Select DIGITAL IN (COAXIAL) THRU (DIGITAL OUT) Recording Equipment,etc. DIGITAL IN (COAXIAL) (OPTICAL) DIGITAL OUT Mixer,etc. CD Player, MD Player,etc. BR-8/532/1180, etc Tips about high sound quality playback • Please pay careful attention to the placement location. In order to take full advantage of the low-frequency playback capabilitie
Краткое содержание страницы № 9
Connection Examples Important Notes on Placement • During setup and transport, be careful not to damage the • When this unit is in operation, the top side will become vibrating portions (the speaker cone and diaphragm). hot. Take care not to touch it. • Be sure to place the monitor so that the slits on the top to • Do not put anything on the unit. radiate the heat is not obstructed. Also, make sure the • During operation, this unit must be placed at a distance monitor doe
Краткое содержание страницы № 10
Reference Troubleshooting If there is no sound or if the unit does not operate as you expect, please check the following points first. If this does not resolve the problem, contact the nearest Roland service center or authorized Roland distributor. There’s No Sound The volume level of the instrument connected to ANALOG INPUT is too • Make sure the Input Level control has not been turned low fully counterclockwise. • Could you be using a connection cable that contains a • Make sure the Input
Краткое содержание страницы № 11
Reference • Power Supply • Weight AC 117 V, AC 230 V, AC 240 V 6.1 kg/13 lbs 8 oz • Accessories • Power Consumption Owner's Manual 40 W Power Cord • Dimensions 176 (W) x 249.5 (D) x 280 (H) mm 6-15/16 (W) x 9-7/8 (D) x 11-1/16 (H) inches 962a * In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice. Dimensions fig. 176 (6-15/16") 241 (9-1/2") 280 (11-1/16") 8.5 (3/8") 249.5 (9-7/8") * Not include the power cord. Frequ
Краткое содержание страницы № 12
02901001 2RCC
