Краткое содержание страницы № 1
LCD Monitor
CF-VDL02BM
OPERATING INSTRUCTIONS
ENGLISH
Introduction......................................4
Names and Functions of Parts .......5
Mounting the LCD Monitor ..............6
E
Starting Up/Shutting Down .............8
Touchscreen ....................................9
Adjusting the LCD Monitor ...........13
Troubleshooting ............................17
Specifications ................................19
INSTRUCTIONS D’UTILISATION
FRANÇAIS
Introduction................................. 22
Краткое содержание страницы № 2
ENGLISH Used in Motor Vehicle For Used in Motor Vehicle Warning: A LCD monitor may be installed in a motor vehicle and visible to the driver only if used to support vehicle related functions such as vehicle information, system control, rear or side observation and navigation. If used for entertainment purpose, such as television recep- tion or video play, it must be installed to the rear of the driver’s seat where it will not be visible, directly or indirectly, to the operator of the motor vehic
Краткое содержание страницы № 3
Precautions When Car Washing Do not expose the LCD monitor to water or excessive moisture. This could cause electrical shorts, fire or other damage. When Parked Parking in direct sunlight can produce very high temperatures inside your car. Let the interior of the car cool down before switching the unit on. Do not watch the LCD monitor with the engine off. It will consume battery power and may prevent the engine from starting. Use Panasonic Technical Support Do not attempt to disassemble or adj
Краткое содержание страницы № 4
Introduction Thank you for purchasing the LCD Monitor for the Panasonic notebook computer series. This LCD monitor features a touchscreen function, which makes computer operation pos- sible by simply touching the surface of the LCD monitor and pressing buttons – even when the computer is not being held. LCD Monitor ................................ 1 Operating Instructions ............... 1 Sun Shade ................................... 1 RGB/Serial/Sound Cable ............ 1 E PS/2 Cable ........
Краткое содержание страницы № 5
Names and Functions of Parts LCD LED Indicator Green : power on Orange : power on but Function Buttons no VGA Sig- F1 Does the same operation as nal or the through F5 of the keyboard. cable is not Speaker connected. Power Switch Speaker Emergency Button The application software Speaker Volume allocated to F11 is started up. E up Temperature LED Indicator down Green : Normal Brightness Volume The brightness can be adjusted freely. up Orange : Drops the brightness automatica
Краткое содержание страницы № 6
Mounting the LCD Monitor 1 Connect your computer to the port replicator ( Operating Instructions of the port replicator) 2 Remove the cover of the LCD Monitor Remove the four screws, and remove the cover. 3 Connect the LCD Monitor to your computer via the connection cables (in- cluded) E Example of connection LCD Monitor RGB IN Display Port Function Key Port Fn KEY Sound Port LINE IN Serial Port SERIAL I/F DC-IN
Краткое содержание страницы № 7
4 Attach the cover of the LCD Monitor Attach the four screws. 5 Mount the Sun Shade Attach the two screws (included). E 6 Mount the LCD Monitor Use these M4 screw holes to mount the LCD Monitor. CAUTION When installing the LCD monitor, lo- cate the monitor under the dashboard as shown in the figure to prevent the monitor from interrupting the sight of the driver and to prevent the moni- tor from being hit by direct sunlight. Do not expose the computer to direct sunlight or excessive heat. 7
Краткое содержание страницы № 8
Starting Up/Shutting Down Starting Up 1 Press the power switch of the LCD Monitor The LCD Monitor will turn on. 2 Turn your computer on ( Operating Instructions of the computer) NOTE Some computers will turn on automatically when the LCD Monitor is turned on. 3 Select your application You are able to start working on your computer. Shutting Down (power off your computer) E This procedure is for shutting down the computer without using the standby or hibernation function. ( Reference Manual of t
Краткое содержание страницы № 9
Touchscreen The LCD Monitor is equipped with a touchscreen function allowing you to perform the same operations as the touch pad or mouse by touching the surface of the display with the finger or stylus. The operation settings can be changed in the following menu. Windows XP : [start] - [All Programs] - [UPDD] - [Settings]. Windows 2000 : [Start] - [Programs] - [UPDD] - [Settings]. NOTE The touchscreen feature cannot be used with models which do not have a serial port. For some models, you first
Краткое содержание страницы № 10
Touchscreen CAUTION The touchscreen function can not be used when using the full screen in [Command Prompt]. When the operation of panning is performed, the touchscreen function will not work properly. If a change is made to the screen resolution, or the cursor can not be pointed correctly with the finger or stylus, be sure to perform calibration. Handling the Touchscreen Do not place any object on the surface or press down forcefully with sharp-pointed ob- jects (e.g., nails), hard objects that
Краткое содержание страницы № 11
Configuring the Touchscreen When needed, the touchscreen can be configured using the following steps. 1 Windows XP Select from the taskbar and select [Adjust settings], or select [Settings] from [start] - [All Programs] - [UPDD] Windows 2000 Select from the taskbar and select [Adjust settings], or select [Settings] from [Start] - [Programs] - [UPDD] The following screen will be displayed. General Set the general settings and functions. Events Set the events that can Windows E be generated by a
Краткое содержание страницы № 12
Touchscreen 2 Make necessary changes 3 Select [OK] NOTE Adjustments can be made when double-click operations are assumed by the com- puter although single-click operations are intended, by clicking [Windows] from the display shown in the previous page and decreasing the value for [Time] in [Double Click Settings]. Immediately run [Calibrate] when the number of Calibration Points is changed. 1 It is also possible to change the double click speed for [Tap and Buttons]* . It is important to note th
Краткое содержание страницы № 13
Adjusting the LCD Monitor Fine adjustment on the display size, position, and so on, may be necessary since the signal timing differs depending on the computer. 1 Press The OSD main menu is displayed. NOTE The OSD window may not be displayed properly when pressing . In this case, press again after waiting for about 10 seconds. ICON FUNCTION DESCRIPTION Brightness Brightness Adjust brightness E Contrast Adjust contrast 1:Exit 2:Select Color Set RGB color Position Move input image
Краткое содержание страницы № 14
Adjusting the LCD Monitor 2 Select the icon by pressing or , then press (Brightness) The Brightness menu item is used to adjust the bright- Brightness ness. A slider indicating the current brightness value is 32 displayed. The adjustment range is 0 to 63. Adjust by pressing or , then press . (To cancel, press and then turn off the power to the LCD Moni- tor. When the power is turned on again, the operation will be canceled.) (Contrast) The Contrast menu item is used to adjust the cont
Краткое содержание страницы № 15
(Position) The Position menu allows the adjustment of image po- Image Position sition in Analog input mode. H-Position Select the item by pressing or , then press . V-Position H-Position Auto Center H-position is used to adjust the horizontal image posi- tion manually. A slider and the current value are dis- played. The adjustment range is 0 to 127. Adjust by pressing or , then press . (To cancel, press and then turn off the power to the LCD Monitor. When the power is turned on again, t
Краткое содержание страницы № 16
Adjusting the LCD Monitor Auto Phase A confirmation box is displayed. The default selection is [Yes]. Press to adjust the phase automatically. If you want to cancel, select [No] and press . To save the adjusted value, select [Phase] or [Clock], then press . (Auto Configuration) Auto Configuration automatically adjusts image posi- Auto Config tion, clock, and phase. Yes No A confirmation box is displayed. The default selection is [Yes]. Press to execute the menu. If you want to cancel, select
Краткое содержание страницы № 17
Troubleshooting When a problem occurs, refer to this page. If a problem appears to be related to a software application, read the software related manual. If you still cannot troubleshoot the problem, contact Panasonic Technical Support. No display after power- Check the cable connection for the car adaptor. ing on Check the cable connection to the LCD Monitor. Check the brightness of the LCD Monitor. or If the LCD of the computer is ON, press Fn + F3 . Has the computer been set to the
Краткое содержание страницы № 18
Troubleshooting Unable to input by Check the cable connection to the LCD Monitor. touching the display Confirm that the [Serial Port] has not been set to [Dis- able] in the Setup Utility. 1 Confirm that the setting for resource in [UPDD]* - [Set- tings] - [Hardware] and the setting of the Serial Port in the Setup Utility are the same. 1 * Windows XP : [start] - [All Programs] - [UPDD] Windows 2000 : [Start] - [Programs] - [UPDD] The display is affected The mode not supported has been selected. S
Краткое содержание страницы № 19
Specifications Model No. CF-VDL02BM Input Interface Analog RGB Signal LCD Type 12.1 type TFT Color Active Matrix LCD Display Area 247.2 mm × 185.7 mm Resolution 1024 × 768 dots Color 262,144 (simulated 16,777,216) Colors Pixel Pitch 0.24 mm × 0.24 mm 2 Brightness 1200 cd/m Display Modes VGA 640 × 480 60 Hz SVGA 800 × 600 60 Hz XGA 1024 × 768 60 Hz Touchscreen Resistive E Interface Display Port Dsub 15-pin female Serial Port Dsub 9-pin male Line IN Miniature jack, 3.5 DIA Function Key F1-F5, Emer
Краткое содержание страницы № 20
FRANÇAIS Pour L’utilisation Dans Un Véhicule Motorisé Avertissement : Le Moniteur LCD peut être installé dans un véhicule motorisé et dans le champ de vision du conducteur uniquement en tant que dispositif d’aide aux fonctions du véhicule, comme par exemple pour fournir des informations sur le véhicule, comme dispositif de contrôle de système, pour l’observation à l’arrière ou sur les côtés du véhicule, ainsi que pour fournir de l’information routière. Pour toute utilisation à fin de divertissem
