Краткое содержание страницы № 1
S I T E M O N I T O R I N G
■ ■ ■ ■ ■ ■ ■ ■
MR1
Mini-Remote
Environmental Monitor
USER MANUAL
Краткое содержание страницы № 2
Краткое содержание страницы № 3
TABLE OF CONTENTS Section 1: INTRODUCTION.......................................................................................... 1 Specifications ................................................................................................................................................ 1 Section 2: INSTALLATION........................................................................................... 3 Mounting.........................................................................
Краткое содержание страницы № 4
Figure 1. Typical System Configuration
Краткое содержание страницы № 5
Краткое содержание страницы № 6
Section 1: INTRODUCTION The Liebert MR1 Mini-Remote monitors the operating status and controls the operation of your Liebert Environmental unit. It serves as a remote user interface, supplementing the unit-front controls. The MR1 is compatible with all Liebert microprocessor- controlled Environmental units, including: • Deluxe System 3 and Challenger units with • Advanced Microprocessor with Graphics • Advanced Microprocessor • Standard Microprocessor • Level 10 • Level 00 •
Краткое содержание страницы № 7
NOTE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
Краткое содержание страницы № 8
Section 2: INSTALLATION Mounting The MR1 Mini-Remote is completely tested, then shipped from the factory disassembled for your convenience during installation. To begin flush-mount installation, please refer to Figure 2A. An optional 30-foot control cable can be supplied to allow the display to be located remotely from the electrical box. Refer to Figure 2b. The electric box containing the power supply is designed for flush-mounting into a finished interior wall. A wall plate i
Краткое содержание страницы № 9
Figure 2a. Flush-Mount Installation 4 • User Manual
Краткое содержание страницы № 10
Electrical Connections The MR1 Mini-Remote requires a two-wire connection (field- supplied) to communicate with the Environmental unit under its control. The stranded twisted-pair connects to the MR1 interface board at TB2-11 (T+) and TB2-12 (T-). Refer to Table 1 below for the connections at the Environmental unit. Note that maximum length for RS-422 communications is 1000 feet, and minimum of 22 gauge wire should be used for all field wiring. Power for the MR1 is supplied to TB3-1 and
Краткое содержание страницы № 11
Figure 2b. Display Panel Mounted Remotely from Electrical Box 6 • User Manual
Краткое содержание страницы № 12
Section 3: HARDWARE CONFIGURATION DIP Switch Settings The following user selectable operations are set by DIP SW1 on the display panel circuit board: Refer to Table 2 and Figure 3. Position OFF ON 1 Audible beeper Audible beeper enabled disabled 2 Remote on/off Remote on/off of disabled. On/off Env. unit enabled. button affects MR1 Env. unit must have operation only remote on/off capability, or MR1 will not be able to perform this function 3 Optional alarm inputs 4 optiona
Краткое содержание страницы № 13
Figure 3. Electrical Connections, Electric Box and Display 8 • User Manual
Краткое содержание страницы № 14
Section 4: OPERATION LCD and Keypad When power is first applied, the MR1 performs self- initialization and then enters the normal display mode. The display alternates between showing the temperature and humidity readings, and cooling/heating, de/humidification, and econocycle operating status. Pressing the HOLD button will lock on the temperature or humidity reading, continuously updating it two times per second. It will continue to display the same parameter until the SCAN bu
Краткое содержание страницы № 15
button will turn on/off the unit being monitored and the MR1. With DIP switch #2 in the OFF position, pressing the ON/OFF button will turn toggle the on/off operation of the MR1 only. Setpoint Control There are two hidden buttons on the MR1 keypad. These buttons are not labeled on the display to prevent untrained personnel from accessing unit settings. Figure 5. Display Panel The F/C button will toggle between degrees Fahrenheit and degrees Celsius for the temperature display. The S
Краткое содержание страницы № 16
Setpoint AM/AG SM L10 L00 MM2 SSC On/Off ✔ ** ✔ ** ✔ ✔ Temperature ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ Temp Sensitivity Humidity ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ Humidity Sensitivity High Temperature Alarm ✔ ✔ ✔ ✔ ✔ ✔ Low Temperature Alarm High Humidity Alarm ✔ ✔ ✔ ✔ ✔ ✔ Low Humidity Alarm Table 3: Setpoint Control by Microprocessor ** Modification to the K3 common alarm relay on the microprocessor controls of the Environmental unit is necessary to enable remote on/off – this modification
Краткое содержание страницы № 17
Alarm AM/AG SM L10 L00 MM2 SSC High Temperature ✔ ✔ ✔ ✔ ✔ ✔ Low Temperature ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ High Humidity Low Humidity ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ High Head Pressure 1 High Head Pressure 2 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ Loss of Airflow Liquid Detected ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ Change Filters Humidifier Problem ✔ ✔ ✔ No Water in Hum’fier Pan ✔ ✔ ✔ ✔ ✔ ✔ Standby Glycool Unit On Compressor 1 Overload ✔ ✔ ✔ ✔ ✔ ✔ Compressor 2 Overload Main Fan Overload ✔ ✔ ✔ ✔ ✔ ✔ Ma
Краткое содержание страницы № 18
Краткое содержание страницы № 19
■ ■ ■ ■ ■ ■ ■ ■ MR1 Mini-Remote Environmental Monitor LIEBERT CORPORATION THE COMPANY BEHIND EARBORN DRIVE 1050 D THE PRODUCTS P.O. BOX 29186 COLUMBUS, OHIO 43229 800.877.9222 PHONE With more than 500,000 installations around the globe, Liebert is the world leader in computer protection systems. Since its 614.841.6022 FAX founding in 1965, Liebert has developed a complete range of support and protection systems for sensitive electronics:
