Краткое содержание страницы № 1
User’s Manual
Color LCD Monitor
It shall be assured that the final system is in compliance to
IEC60601-1-1 requirements.
Краткое содержание страницы № 2
Краткое содержание страницы № 3
English TABLE OF CONTENTS PRECAUTIONS ...................................................................................4 1. INTRODUCTION .....................................................................................9 1-1. Features ........................................................................................................9 1-2. Package Contents..........................................................................................9 1-3. Controls & Connectors .............
Краткое содержание страницы № 4
Краткое содержание страницы № 5
Краткое содержание страницы № 6
Краткое содержание страницы № 7
Краткое содержание страницы № 8
English LCD Panel In order to suppress the luminosity change by long-term use and to maintain the stable luminosity, please use the monitor with the brightness below 150 2 cd/m (BRIGHTNESS approximately 85 %). The screen may have defective pixels. These pixels may appear as slightly light or dark area on the screen. This is due to the characteristics of the panel itself, and not the product. The backlight of the LCD panel has a fixed life span. When the screen becomes dark or begins to fl
Краткое содержание страницы № 9
English 1. INTRODUCTION Thank you very much for choosing an EIZO Color Monitor. 1-1. Features • Dual inputs compliant (DVI-I and D-Sub mini 15 pin connecters) • DVI (p. 49) Digital input (TMDS (p. 50)) compliant • [Horizontal scanning frequency] Analog: 31 - 94 kHz Digital: 31 - 76 kHz [Vertical scanning frequency] Analog: 49 - 86 Hz (1600 x 1200: 49 - 76 Hz) Digital: 59 - 61 Hz (VGA text: 69 - 71 Hz) [Resolution] 2M pixels (1600 dots × 1200 lines) [Frame synchronous mo
Краткое содержание страницы № 10
Краткое содержание страницы № 11
Краткое содержание страницы № 12
English 2. CABLE CONNECTION 2-1. Before Connecting Before connecting your monitor to the PC, change the display screen settings (resolution p. 50) and frequency) in accordance with the charts below. NOTE • When your computer and display support VESA DDC, the suitable resolution and the refresh rate are set by just plugging your display into the computer without any manual settings. Analog Input Resolution Frequency Dot Clock Remarks 640 480 67 Hz 202.5 MHz Apple Macintosh × (Max.) × 64
Краткое содержание страницы № 13
English 2-2. Connecting the signal cable (For the computer employing D-Sub or DVI connector) NOTE • Be sure that the power switches of both the PC and the monitor are OFF. 1. Plug the signal cable into the connector at the rear of the monitor and the other end of the cable into the video connector on the PC. After connecting, secure the connection with the screw-in fasteners. Power Cord Analog Input Signal Cable Connector PC Signal Cable (MD-C87 Video Output • Standard graphics car
Краткое содержание страницы № 14
English Digital Input Signal Cable Connector PC Signal Cable (FD-C39 Video Output • Digital graphics board enclosed) Connector / DVI • Power Mac G4(DVI) Input Connector (monitor) / DVI 2. Plug the power cord into the power connector on the rear of the monitor. 3. Lead the power cord and signal cable into the cable holder at rear of the monitor. NOTE • When housing the cables into the cable holder, lead them to the cable entrance side and pinch the projection to open the cable entra
Краткое содержание страницы № 15
English WARNING The equipment must be connected to a grounded main outlet. Not doing so may result in fire or electric shock. Not doing so may result in fire or electric shock. 5. Turn on the monitor’s Power Button and then switch on the PC’s power. The monitor’s power indicator will light up (blue). If an image does not appear, refer to the “7. TROUBLESHOOTING” (p.40) for advice. Whenever finished, turn off the PC and the monitor. NOTE • When turning on the monitor, the kind of the
Краткое содержание страницы № 16
English 2-3. Connecting the signal cable (For the computer employing ADC) NOTE • Be sure that the power switches of both the PC and the monitor are OFF. 1. Plug the signal cable into the connector at the rear of the monitor and the other end of the cable into the video connector on the PC. After connecting, secure the connection with the screw-in fasteners. Power Cord To Input the Signal Through ADC Signal Cable Connector PC Signal Cable (FD-C39, enclosed) Video Output Connector/
Краткое содержание страницы № 17
English 3. Lead the power cord and signal cable into the cable holder at rear of the monitor. NOTE • When housing the cables into the cable holder, lead them to the cable entrance side and pinch the projection to open the cable entrance. • The cables are recommended to lead with slight sag for the smooth motion of the stand and the Portrait/Landscape display. Cable Holder Projection Cable Entrance 4. Plug the other end of the cord into a power outlet. The monitor’s power indicator will f
Краткое содержание страницы № 18
English 5. Press the power button while pressing the Input Signal Selection button. The Input Selection menu is appeared on the screen. Power Enter Button Power Button Indicator Input Signal Selection Control Buttons Button (Up, Down, Left, Right) 6. Change SIGNAL 1 (DVI-I Connector) in the Input Selection menu to “ADC”. Press Enter button to complete the setting and the menu closes. 7. Switch on the PC's power. The monitor’s power indicator will light up (blue). If an image does not appe
Краткое содержание страницы № 19
English 2-4. Connecting Two PCs to the Monitor Two PCs can be connected to the monitor through the Signal 1 and the Signal 2 on the back of the monitor. Connecting Examples D-Sub 15 pin mini DVI-I Input Input Connector Connector (SIGNAL 2) (SIGNAL 1) PC 1 PC 2 (Ex.1) Analog D-Sub Signal Cable Signal Cable D-Sub Analog mini 15 mini (FD-C16 enclosed) (MD-C87 enclosed) pin 15 pin (Ex.2)Digital DVI Signal Cable Signal Cable (MD-C87 D-Sub Analog enclosed) mini (FD-C39 enclosed) 15 pin
Краткое содержание страницы № 20
English The Priority Input Signal This function is used to select which PC will have priority to control the monitor when utilizing two PCs. The monitor constantly checks the input signals and switches automatically in accordance with the “Input Priority” setting (see table below). Once a priority is set, whenever a change of signal is detected at the selected input, the monitor will switch the input to that signal. In the case of only one signal being present at either input, the monito
