Краткое содержание страницы № 1
Distributed by:
www.Jameco.com ✦ 1-800-831-4242
The content and copyrights of the attached
material are the property of its owner.
Краткое содержание страницы № 2
® SUPERPRO series Universal Programmers For Windows 95/98/NT/2000 User’s Guide XELTEK
Краткое содержание страницы № 3
COPYRIGHTS Software Copyrights 1997-2000 XELTEK User's Guide Copyrights 1997-2000 XELTEK This software product is copyrighted. All rights are reserved. The distribution and sales of the products are intended for use by the original purchaser under the terms of the License Agreement. This User's Guide is copyrighted. All rights are reserved. This document may not, in whole or part, be copied, photocopied, reproduced, tran
Краткое содержание страницы № 4
Contents 1. General Description 1.1 Introduction 1.1.1 What is Superpro? 1.1.2 Manual Organization 1.1.3 Manual Convention 1.1.4 System Requirement 1.3.2 Package 1.2 System Setup 1.2.1 Software Installation 1.2.2 Hardware Installation 1.2.3 Running the Program 1.2.4 Communication Error message 1.2.5 Device Insertion 1.3 Programming Operation 1.3.2 Quick Guide to Programming 1.3.3 Error Messages 2. D
Краткое содержание страницы № 5
2.3.3 Select 2.3.4 Word Format 2.4 Test: 2.4.1 New Pattern 2.4.2 Edit Pattern 2.4.3 Delete Pattern 2.4.4 TTL&CMOS test 2.4.5 Auto find device 2.4.6 Vector test 2.5 Option: 2.5.1 Setting 2.5.2 Auto Increment 2.5.3 Load configure file 2.5.4 Save configure file 3. Appendices 3.1 Customer Support 3.2 Error Messages 1.General Description
Краткое содержание страницы № 6
1.1 INTRODUCTION 1.1.1 What is Superpro? The SUPERPRO is a family of affordable, reliable, and fast universal IC device programmers. They are designed to communicate through a parallel (printer) or USB port(model dependent) and to operate with Intel 80486- and Pentium-based IBM- compatible desktop computers and notebook computers. Menu-driven software interface makes them easy to operate. Programming hardware include the following items. 1. A sleek, low-profile, programming mo
Краткое содержание страницы № 7
Up arrow key = Down arrow key = Unless stated otherwise, keystrokes are not case-sensitive. e.g.: Both 'A' and 'a' are acceptable. 1.3.2 System Requirements The minimum requirement is as follows: 1. A 486 or Pentium PC, desktop or laptop. 2. One parallel port, such as LPT1 (278H), LPT2 (378H), or LPT3 (3BCH). 3. MS Windows9x, NT or 2000 operating system (model dependant) 4. Diskette drive (3.5" 1.44 Mbytes) or CD-ROM for installation 5. Hard disk storag
Краткое содержание страницы № 8
switch and observe the power LED coming on bright. Please be sure not to insert any chip onto the programmer socket at this time. 1.2.3 Running the Program Please run the main program for the programmer. If everything is set up correctly, then the main screen should come up without any error message. At this point, you may select a device and proceed with programming operation. Figure1. Main Screen 1.2.4 Communication Er
Краткое содержание страницы № 9
1.2.5 Device Insertion For chips in DIP package Follow the reference diagram next to the socket. Chips are always inserted at the bottom line of the ZIF socket with the pin 1 facing toward upper left corner. For some low-end models, some devices may need to be inserted in a non-standard way. Instruction for insertion of such devices will appear on the screen when the selection of the device is made. For chips in None-DIP packages Socket adapters are available for PLCC, QFP, TSOP,
Краткое содержание страницы № 10
selection of the device to read from. Click on Run from the main screen, which will pop up the Function screen. Click on the Read function, which copies the data from the master chip into the buffer. At this point you may go to the buffer and examine the data to see if it is loaded correctly. The data may be saved to a disk for later use. Program device: Insert blank chip into the socket and enter on Program function. Device should begin programming at this time followed by verificati
Краткое содержание страницы № 11
Figure 8 Data type 2.1.2 Save This selection will save the current data in the buffer to disk. For E(E)PROM, BPROM or MCU device types, Save File window will pop up. Select the folder and filename to be saved under. Next, File Type dialog box will pop up for selecting file type to be saved under. For PLD devices, the Save JED File dialogue box will pop-up to enter the file name. 2.1.3 Exit This command closes the program
Краткое содержание страницы № 12
Figure 9. Edit Buffer Locate The function is convenient for locating a set of data for editing. In the Locate Buffer dialog box, key in the address you wish to see displayed and press OK. The cursor will blink at the address specified in the space marked New Address. Fill The function will bring up the Fill Buffer dialogue box. It consists of the Start Address, End Address, Fill Data input lines, OK and Cancel buttons. Input desired data to be
Краткое содержание страницы № 13
Swap MSB and LSB byte order for the specified word width in the address range. Figure 13. Swap Buffer Radix Toggles between HEX and DEC (Decimal) memory address display. Search Searches for a combination of HEX/ASCII codes (search string). Next Performs the next search for the search string in Search. 2.2.2 Encryption Table The Load Encryption Table, with its two sub-menus, manages an en
Краткое содержание страницы № 14
This opens the Vector Buffer Edit window. If a test vector table is included in the JEDEC file, the software will load the test vector table to the buffer automatically when the JEDEC file is loaded. Refer to the following when editing the test vector. Z: High impedance state X: Don't care state N: Vcc and ground (output pins are not tested) H: Output logic High (Voh) L: Output logic low (Vol) C: Clock pin 1: Input logic High (Vih) 0: Input logic Low (Vil) 2.3 Device:
Краткое содержание страницы № 15
Figure 15. Run Program The function writes the data from the buffer into the chip. The Verify function is performed automatically after programming. If an error occurs, the error message will be displayed along with the addresses and data of the chip and buffer where the error occurred. Any other result will be displayed in the message section. The current address is incremented in the Current Address display window while the chip is being
Краткое содержание страницы № 16
Verify The function compares the content of the buffer to that of the chip. If there is any discrepancy, verify failure message and the address where it started failing will be displayed in the Message window. For PROM or MCU devices, verification of range between start and end addresses (specified by you) is available. Blank Check The function checks if the device is in blank state. For a ROM or MCU, checking of a range between a start and end address (specified by you) is possib
Краткое содержание страницы № 17
Chip End Input an address for the chip where you would like a selected function of downloading or uploading to end. This is normally set to the end address of the chip. Buff Start This sets the address in the buffer where file loading begins. By changing the address, a file can be loaded at any desired location. Buff End This sets address in the buffer where file loading ends. By changing the address, a file can end loading at any desired location. Note: Chip Start, Chip E
Краткое содержание страницы № 18
Edit box. When the highlighted cursor is placed over a name of the manufacturer, names of the devices for the manufacturer selected will be displayed instantly in the Device column. Type radio button allows you to select one of the different device types, such as, E/EPROM, PLD, MCU,etc. Select the device type first before selecting Manufacturer of a device. Search Edit box allows you to search device quickly. Figure 17. Select De
Краткое содержание страницы № 19
The Word Format window allows you to specify the data format loaded into the buffer. The default setting is Byte format. Word or Double Word format may be selected. For programming into byte- wide chip further selection to byte level is needed. Byte 8-bit data format is selected. Even Word In the 16 bit word format, selection of Even Word will program only the even data bytes For example, if the data is; buffer address 00 01 02 03 04 05 06 buffer data 01 23 45 67
Краткое содержание страницы № 20
Figure 18. Word Format 2.4. Test: The SUPERPROs can test logic ICs and RAM devices, as well as perform vector testing on PLDs. The user-friendly software provides an easy interface for loading files, editing test patterns, and downloading and uploading data between the buffer and the device. The SUPERPROs provide a 74/54 and 4000/45000 TTL/CMOS logic device test library, and memory test algorithms. Following sections describe the functions available for test
