Краткое содержание страницы № 1
GA-4MXSV
Pentium Prescott 1066 Motherboard
USER’S MANUAL
®
Pentium Prescott Processor Motherboard
Rev. 1002
12ME-4MXSV-1002
Краткое содержание страницы № 2
GA-4MXSV Motherboard Table of Content Item Checklist ........................................................................................ 4 WARNING! ............................................................................................... 4 Chapter 1 Introduction ............................................................................ 5 Features Summary ...................................................................................... 5 GA-4MXSV Motherboard Layout ...........
Краткое содержание страницы № 3
English Table of Content Chapter 4 Technical Reference ............................................................ 61 Block Diagram ........................................................................................... 61 Chapter 5 Driver Installation .................................................................. 62 A.Intel Chipset Software Installation Utilities .................................................................. 62 B.Intel LAN Driver Installation .....................
Краткое содержание страницы № 4
GA-4MXSV Motherboard Item Checklist The GA-4MXSV motherboard Serial ATA cable x 4 IDE (ATA100 ) cable x 1 / Floppy cable x 1 I/O Shield Kit CD for motherboard driver & utility GA-4MXSV user’s manual WARNING! Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To protect them against damage from static electricity, you should follow some precautions whenever you work on your computer. 1. Unplug your computer when working on the inside. 2. Use a
Краткое содержание страницы № 5
Introduction Chapter 1 Introduction Features Summary Form Factor 12” x 9.6” ATX size form factor, 6 layers PCB. ® CPU Supports Intel Pentium Prescot and Smithfieldprocessor ® Intel Prescott LGA 775 supports 800/1066MHz FSB L2 cache on-die per processor from 1M ® Chipset Intel Mukilteo Chipset ® Intel ICH7R ® Intel 6702PXH-V Memory 4 x DDRII socket up to 8 GB Supports Dual Channel Un-buffered DDRII 533/667 Support 256MB, 512MB, and 1GB memory Single-bit Errors Correction, Multiple-bi
Краткое содержание страницы № 6
GA-4MXSV Motherboard On-Board Graphic ATI ES1000 with 16Mb DDR SDRAM On-Board LAN Dual Intel 82573V Gigabit Ethernet controllers Hardware Monitor Winbond 83792D controller Enhanced features with CPU Vcore, 1.5V reference, VCC3 (3.3V), VCC5V, +12V, 2.5V,VBAT3V, +5V SB, CPU Temperature, and System Temperature Values viewing by Support basic ASF remote transaction through CSA Bus with hardware circuit BIOS Phoenix BIOS on 8Mb flash RAM Software mini BMC Additional Features PS/2 Mouse wake
Краткое содержание страницы № 7
Introduction GA-4MXSV Motherboard Layout 5 O O P M U V W X Y A L 6 Q 2 E R S J T 7 B D 3 4 1 K C Z 8 F I H N G 9 7
Краткое содержание страницы № 8
GA-4MXSV Motherboard A. CPU U. PCI_B B. Intel Mukilteo V PCI_A C. Intel 6702 PXH-V W. PCI-E x8 D. Intel ICH7R X. PCI-X_2 E. ITE IT8712F Y. PCI-X_1 F. SATA1 Z. BAT (Battery) G. SATA2 1. ATX H. SATA3 2. ATX12V I. SATA4 3. WOR J. FDC 4. WOL K. IDE 5. UF1 (CPU FAN) L. F_Panel 6. UF2 (System FAN) M. COM2 7. UF3 (System FAN) N. USB2 8. UF4 (System FAN) O. Intel 82573V GbE 9. UF5 (System FAN) P. ATI RN50 Q. DDRII A1 R. DDRII A2 S. DDRII B1 T. DDRII B2 8 English
Краткое содержание страницы № 9
Connector Introduction Chapter 2 Hardware Installation Process To set up your computer, you must complete the following steps: Step 1- Install the Central Processing Unit (CPU) Step 2- Install memory modules Step 3- Install expansion cards Step 4- Connect ribbon cables, cabinet wires, and power supply Step 5- Setup BIOS software Step3 Step1 Step4 Step 4 Step 4 Step4 Step 2 9
Краткое содержание страницы № 10
GA-4MXSV Motherboard Step 1: Installing Processor and CPU Haet Sink Before installing the processor and cooling fan, adhere to the following cautions: 1. The processor will overheat without the heatsink and/or fan, resulting in permanent irreparable damage. 2. Never force the processor into the socket. 3. Apply thermal grease on the processor before placing cooling fan. 4. Please make sure the CPU type is supported by the motherboard. 5. If you do not match the CPU socket Pin 1 and CPU cut edge
Краткое содержание страницы № 11
Hardware Installation Process Step1-2: Installing Heat Sink Male Push Pin The top of Female Push Pin Female Push Pin Fig.1 Fig. 2 Please apply heatsink paste on the surface of ( to remove the heatsink, turning the push pin along the installed CPU. the direction of arrow; and reverse the previous step to install the heat sink.) Please note the direction of arrow sign on the male push pin doesn't face inwards before installation. (This instruction is only for Intel boxed fan) Fig. 3 Fig. 4 Place t
Краткое содержание страницы № 12
GA-4MXSV Motherboard Step 2: Install memory modules Before installing the processor and heatsink, adhere to the following warning: When DIMM LED is ON, do not install/remove DIMM from socket. GA-4MXSV has 4 dual inline memory module (DIMM) socets. It supports the Dual Channel Technology. The BIOS will automatically detects memory type and size during system boot. For detail DIMM installation, please refer to the following instructions. Channel B Channel A 12 English
Краткое содержание страницы № 13
Hardware Installation Process Table 1. Supported DIMM Module Type Technology Organization SDRAM Chips/DIMM 256MB 8MB x 8 x 4 bks 8 16MB x 4 x 4bks 16 512MB 16MB x 8 x 4bks 8 32MB x 4 x 4bks 16 1GB 32MB x 8 x 4bks 8 64MB x 4 x 4bks 16 Table 2. DIMM Placement DDR2-533/667 DIMM Configuration DIMM1 DIMM2 1 Single Rank Empty Empty 1 Dual Rank Empty Empty 2 Single Rank Empty Single Rank 1 Dual Rank, 1 Single Rank Empty Single Rank 2 Dual Rank Empty Dual Rank Installation Steps: 1. Unlock a DIMM socket
Краткое содержание страницы № 14
GA-4MXSV Motherboard Step 3: Install expansion cards 1. Read the related expansion card’s instruction document before install the expansion card into the computer. 2. Remove your server’s chassis cover, necessary screws and slot bracket from the computer. 3. Press the expansion card firmly into expansion slot in motherboard. 4. Be sure the metal contacts on the card are indeed seated in the slot. 5. Replace the screw to secure the slot bracket of the expansion card. 6. Replace your computer’s ch
Краткое содержание страницы № 15
Hardware Installation Process Step 4: Connect ribbon cables, cabinet wires, and power supply Step 4-1 : I/O Back Panel Introduction 15
Краткое содержание страницы № 16
GA-4MXSV Motherboard PS/2 Keyboard and PS/2 Mouse Connector To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard to the lower port (purple). USB Port Before you connect your device(s) into USB connector(s), please make sure your device(s) such as USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface. Also make sure your OS supports USB controller. If your OS does not support USB controller, please contact OS vendor for p
Краткое содержание страницы № 17
Connector Introduction Step 4-2 :Connectors & Jumper Setting Introduction N F E O B D P L M A S R T Q V C G J H K I U A) ATX M) WOR1 B) ATX _12V N) UF1 (CPU Fan) C) IDE1 O) UF2 (System Fan) D) FDC1 P) UF3 (System Fan) E) F_Panel Q) UF4 (System Fan) F) COM2 R) UF5 (System Fan) G) USB2 S) CLR_CMOS H) S_ATA1 T) RECOVERY I) S_ATA2 U) PASSWORD J) S_ATA3 V) BAT (Battery) K) S_ATA4 L) WOL1 17
Краткое содержание страницы № 18
GA-4MXSV Motherboard A) ATX (ATX Power Connector) PIN No. Definition 1 +3.3V 2 +3.3V 3 GND 13 4 +5V 1 5 GND 6 +5V 7 GND 8 POK 9 5VSB 10 +12V 11 +12V 12 +3.3V 13 +3.3V 14 -12V AC power cord should only be connected to 15 GND 16 PSON your power supply unit after ATX power cable 17 GND and other related devices are firmly connected 18 GND to the mainboard. 19 GND 12 24 20 -5V 21 +5V 22 +5V 23 +5V 24 GND B ) ATX_12V( +12V Power Connector) 8 1 5 4 Pin No. Definition 1 GND 2 GND 3 GND 4 GND 5 P12V_C
Краткое содержание страницы № 19
Connector Introduction C ) IDE1 (IDE Connector) Please connect first harddisk to IDE1. The red stripe of the ribbon cable must be the same side with the Pin1. 1 39 2 40 D) FDC1 (Floppy Connector) Please connect the floppy drive ribbon cables to FDD. It supports 720K,1.2M,1.44M and 2.88Mbytes floppy disk types. The red stripe of the ribbon cable must be the same side with the Pin1. 1 2 33 34 19
Краткое содержание страницы № 20
GA-4MXSV Motherboard E ) F_Panel1 (2X9 Pins Front Panel connector) Please connect the power LED, PC speaker, reset switch and power switch of your chassis front panel to the F_PANEL connector according to the pin assignment above. 1 2 17 18 Pin No Signal Name Description 1 HD+ Hard Disk LED anode (+) 2 PWLED+ Power LED Signal anode (+) 3 HD- Hard Disk LED cathode(-) 4 PWLED- Power LED Signal cathode(-) 5 GND Ground 6 PW+ Soft power connector anode (+) 7 RESET Reset button 8 GND Ground 9NC No
