Краткое содержание страницы № 1
2804080
® TM
Intel Core Duo/Solo 945GM
Mini-ITX Motherboard
USER’S MANUAL
Version 1.0
Краткое содержание страницы № 2
Acknowledgments Award is a registered trademark of Award Software International, Inc. PS/2 is a trademark of International Business Machines Corporation. Intel and Intel® Core Duo and Intel® Core Solo processors are registered trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation. Winbond is a registered trademark of Winbond Electronics Corporation. All other product names or trademarks are properties of their respective owners. ii 2804080 User’s
Краткое содержание страницы № 3
Table of Contents Introduction .......................................................1 Produ Description.............................................................1 Checklist..............................................................................2 280 40 80 Spe ci fic ations .......... ......... .......... ......... .......... ....... 3 Boar d Di mens ions ......... .......... ......... .......... ......... .......... ...... 4 Installations ..............................................
Краткое содержание страницы № 4
IMPORTANT NOTE: When the system boots without the CRT being connected, there will be no image on screen when you insert the CRT/VGA cable. To show the image on screen, the hotkey must be pressed (CTRL-ALT-F1). THE 2804080 MINI ITX MOTHERBOARD iv 2804080 User’s Manual
Краткое содержание страницы № 5
INTRODUCTION Introduction Product Description The 2804080 Mini ITX board incorporates the Mobile Intel® 945GM Express Chipset for Embedded Computing, consisting of the Intel® 945GM Graphic Memory Controller Hub (GMCH) and Intel® I/O Controller Hub 7-M (ICH7-M), an optimized integrated graphics solution with a 533MHz and 667MHz front-side bus. Dimensions of the board are 170mm x 170mm. The integrated powerful 3D graphics engine, based on Intel® Graphics Media Accelerator 950 (Intel® GMA 9
Краткое содержание страницы № 6
INTRODUCTION Checklist Your 2804080 package should include the items listed below. The 2804080 Mini-ITX motherboard This User’s Manual 1 CD containing chipset drivers and flash memory utility Cable kit (IDE, Serial port, Serial ATA) 2 2804080 User’s Manual
Краткое содержание страницы № 7
INTRODUCTION 2804080 Specifications TM CPU Sup ported Intel® Co re Duo /Solo processors CPU Voltage 0.700V ~ 1.5V (IMVP-6) System Spee d Up to 2.33GHz or above CPU FSB 533MHz/667MHz FSB Cache 2MB Green /APM APM1.2 CPU Socket mPGA 478MT Socket Chipset Intel 945GM Chipset GMCH : 829 45GM 1466-pin Micro-FCB GA ICH7M: 82801 GBM 652-pin mBGA BIOS Award BIOS, support ACPI Function Memory DDR2 667/533 SDRAM DIMM x2 (w/o ECC function), Max. 4GB VGA 945G M built-in, supp orts CR T,RCA,S- VIDE O,HD TV SD
Краткое содержание страницы № 8
INTRODUCTION [ Board Dimensions 4 2804080 User’s Manual
Краткое содержание страницы № 9
INSTALLATIONS Installations This section provides information on how to use the jumpers and connectors on the 2804080 in order to set up a workable system. The topics covered are: Installing the CPU ........................................................................ 6 Installing the Memory .................................................................. 7 Setting the Jumpers ...................................................................... 8 Connectors on 2804080 .......
Краткое содержание страницы № 10
INSTALLATIONS Installing the CPU The 2804080 board supports a Socket 478MT processor socket for Intel® TM TM Core Duo and Intel® Core Solo processors The processor socket comes with a screw to secure the processor. As shown in the left picture below, loosen the screw first before inserting the processor. Place the processor into the socket by making sure the notch on the corner of the CPU corresponds with the notch on the inside of the socket. Once the processor has slide into the socket, fasten
Краткое содержание страницы № 11
INSTALLATIONS Installing the Memory The 2804080 board supports two DDR2 memory socket for a maximum total memory of 4GB in DDR2 memory type. Installing and Removing Memory Modules To install the DDR2 modules, locate the memory slot on the board and perform the following steps: 1. Hold the DDR2 module so that the key of the DDR2 module align with those on the memory slot. 2. Gently push the DDR2 module in an upright position until the clips of the slot close to hold the DDR2 module in place when
Краткое содержание страницы № 12
INSTALLATIONS Setting the Jumpers Jumpers are used on 2804080 to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following lists the connectors on 2804080 and their respective functions. Jumper Locations on 2804080........................................................ 9 JP5: LCD Panel Power Selection.................................................. 10 JP6: 1394 EPROM Write
Краткое содержание страницы № 13
INSTALLATIONS Jumper Locations on 2804080 Jumpers on 2804080...........................................................................Page JP5: LCD Panel Power Selection ................................................. 10 JP6: 1394 EPROM Write Selection ............................................. 10 JP7: Clear CMOS Setting ............................................................. 10 JP8: CompactFlash Slave/Master Selection ................................. 10 280
Краткое содержание страницы № 14
INSTALLATIONS JP5: LCD Panel Power Selection JP3 LCD Panel Power 3.3V 5V JP6: 1394 EPROM Write Selection JP6 1394 EPROM For EPROM Write Normal JP7: Clear CMOS Setting JP4 Setting Normal Clear CMOS JP8: CompactFlash Slave/Master Selection JP8 CF Setting Master Slave [ 10 2804080 User’s Manual
Краткое содержание страницы № 15
INSTALLATIONS Connectors on 2804080 The connectors on 2804080 allows you to connect external devices such as keyboard, floppy disk drives, hard disk drives, printers, etc. The following table lists the connectors on 2804080 and their respective functions. CN1: PS/2 Keyboard and PS/2 Mouse Connectors...................... 13 CN2, CN3: COM1 and VGA Connector...................................... 13 CN4: 10/100 RJ-45 and USB1/2 Ports ......................................... 14 CN5: 1394 Conn
Краткое содержание страницы № 16
INSTALLATIONS Connector Locations on 2804080 12 2804080 User’s Manual
Краткое содержание страницы № 17
INSTALLATIONS CN1: PS/2 Keyboard and PS/2 Mouse Connectors PS/2 Mouse PS/2 Keyboard Signal Name Keyboard Mouse Signal Name Keyboard data 1 1 Mouse data N.C. 2 2 N.C. GND 3 3 GND 5V 4 4 5V Keyboard clock 5 5 Mouse clock N.C. 6 6 N.C. CN2, CN3: COM1 and VGA Connector [ Signal Name Pin # Pin # Signal Name DCD 1 6 DSR RXD 2 7 RTS TXD 3 8 CTS DTR 4 9 RI GND 5 10 Not
Краткое содержание страницы № 18
INSTALLATIONS CN4: 10/100 RJ-45 and USB1/2 Ports CN5: 1394 Connector J12: SPDIF Out Connector CN6: GbE RJ-45 and USB3/4 Ports CN8: Audio Connector The audio connector, from top to bottom, is composed of Line in, Line out and Microphone jacks. CN9, CN10: Serial ATA Connectors FAN1: System Fan Power Connector FAN1 is a 3-pin header for system fans. The fan must be a 12V (500mA). Pin # Signal Name 1 Ground 2 +12V 3 Rotation detection FAN2: CPU Fan Power Connec
Краткое содержание страницы № 19
INSTALLATIONS IDE1: IDE Connector Signal Name Pin # Pin # Signal Name Reset IDE 1 2 Ground Host data 7 3 4 Host data 8 Host data 6 5 6 Host data 9 Host data 5 7 8 Host data 10 Host data 4 9 10 Host data 11 Host data 3 11 12 Host data 12 Host data 2 13 14 Host data 13 Host data 1 15 16 Host data 14 Host data 0 17 18 Host data 15 Ground 19 20 Protect pin DRQ0 21 22 Ground Host IOW 23 24 Ground Host IOR 25 26 Ground IOCHRDY 27 28 Host ALE DACK0 29 30
Краткое содержание страницы № 20
INSTALLATIONS J14: ATX Power Supply Connector 11 1 Signal Name Pin # Pin # Signal Name 3.3V 11 1 3.3V -12V 12 2 3.3V Ground 13 3 Ground PS-ON 14 4 +5V Ground 15 5 Ground Ground 16 6 +5V Ground 17 7 Ground -5V 18 8 Power good +5V 19 9 5VSB 20 10 +5V 20 10 +12V J1: IrDA Connector Pin # Signal Name 1 +5V 2 No connect 3
