Краткое содержание страницы № 1
T E C H N O L O G I E S
Duplicator Panel
Power Switch
Source Drive Bay
Target Drive Bay
User Guide
1:1 HDD Duplicator PRO-S
(HDUSI325AES)
www.addonics.com
v3.1.11
Technical Support
If you need any assistance to get your unit functioning properly, please have your
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Email: http://www.addonics.com/support/query/
Краткое содержание страницы № 2
Table Of Contents ............. Page 3 Basic Instructions ............. Page 5 Functions ............. Page 6 Copy HDD ............. Page 6 Compare HDD ............. Page 7 PreScan Source ............. Page 7 ReScan Bus ............. Page 8 Source Size ............. Page 8 Overwrite ............. Page 8 Setup ............. Page 11 USB Mode ............. Page 11 Advanced Setup ............. Page 15 Basic Troubleshooting ............. Page 16 Error Messages List ............. Page 17 Firmware Upd
Краткое содержание страницы № 3
Basic Instructions I. Installing drive into the HDD Duplicator Note: Make sure that the capacity of the target hard disk is equal or larger than the source hard disk. For installing a hard drive on the various enclosures that come with the HDD duplicator, refer to the bundled enclosure installation guides. When using the Diamond Cipher enclosure, it is important that the cipher key needs to be inserted on the cipher key slot on the enclosure before powering on the HDD Duplicator.
Краткое содержание страницы № 4
IV. Duplicating a drive When the duplicator powers on, it initializes and goes through the steps below Copy HDD copies data directly from the source hard disk to the target hard disk. Press ENT button to begin copy. The system will auto-detect the hard disks and show the following info on the LCD. The LCD will show the following info during the copying process: remaining time, completed percentage. The copy speed, capacity and time will vary depending on the source hard dis
Краткое содержание страницы № 5
Functions The copy controller has 8 functions in total, with the th (Adv Setup) being a hidden system function that only appears when the ESC key is pressed for 2 seconds until there is a beep. These are shown below. 1. Copy HDD 2. Compare HDD 3. PreScan Source 4. ReScan BUS 5. Source Size Duplicator Controller 6. Secure Erase 7. Overwrite 8. Setup 9. USB Mode 10. Adv Setup 10-01. Detect HDD Delay 8-01. Language
Краткое содержание страницы № 6
Copy HDD Copy HDD copies data directly from the source hard disk to the target hard disk. Please make sure that the capacity of the target hard disk is equal or larger than the source hard disk. Choose option 1 from the menu: 1. Copy HDD HDD:1 232.9GB Press ENT to begin copy. The system will auto-detect the hard disks and show the following copying info on the LCD. Copy-36MB/s 0% 232.9GB 00:00:00 The LCD will show the following info during the copying process: elapsed
Краткое содержание страницы № 7
PreScan Source PreScan HDD is used to check if the source hard disk can be accessed properly. It also tests the read speed. Choose option 3 from the menu: 3. PreScan Source HDD : 1 232.9GB Press ENT to begin scan. The LCD will display the following info Scan-90MB/s 1% 230.6GB 00:00:27 Once the scan is complete, the LCD will display the corresp onding results PreScan OK! ReScan Bus ReScan Bus allows swapping the source or target in and out without having to reboot the system. Choo
Краткое содержание страницы № 8
In Process Elapsed 01:00 Overwrite Overwrite is used to overwrite the data of the hard disk, it will erase all HDDs connected to the duplicator (including Source HDD). There are 3 sub-options: One pass, 3 pass and 7 pass. Choose option 7 from the menu: 7. Overwrite Press ENT to access option. By default it is One pass Use the Up and Down arrow keys to choose other options. 7-01. Overwrite One pass Press ENT to access option. By default it is set to No. Use the Up and Down arrow
Краткое содержание страницы № 9
Copy Size This option is used to specify the size of the source hard disk for simplifying further copying operations. 8-02. Setup Copy Size Press ENT and the LCD will display a detailed list of options as shown below Copy Size 100%~1% (*MB) Use the Up and Down arrow keys to choose di erent copy si zes. The system will o er their corresponding percentages so the user can specify the amount to copy from the source hard disk. Press ENT to con rm and save the changes. Startup M
Краткое содержание страницы № 10
Button Sound This option is used to control the sound of a button when you press it. 8-06. Setup Button Sound Press ENT and the LCD will display the following info. Use the Up and Down arrow keys to choose whether button sound is on or o . Button Sound On Device Info This option is used to display the details of all hard disks connected to the copy controller. 8-07. Setup Device Info Press ENT and the LCD will display each hard disk' information in or
Краткое содержание страницы № 11
Adv Setup Adv Setup o ers expert users access to more advanced system settings. To access this option, hold down the ESC key for two seconds until it appears. 10. Adv Setup Detect HDD Delay This function is used to set the time interval between the system's re-scans of all connected HDD devices. Press ENT and the LCD will show the following info. 10-01. Adv Setup Detect HDD Delay Press ENT then use the Up and Down buttons to choose di erent time settings (1~60 sec) Detect HDD Delay 1S
Краткое содержание страницы № 12
Press ENT again and the LCD will prompt you to con rm the erase operation. All data will be lost,Erase? No Quick Erase HDD This function is used to quickly erase all data on the HDD . Please backup any important data before using this function. 10-05.Adv Setup Quick Erase HDD Press ENT to enter the following screen. Use the Up and Down buttons to select the HDD to erase. Quick Erase HDD ALL/Target CH:* H/W Diagnostic Press ENT to enter the following screen. This function is use d to ch
Краткое содержание страницы № 13
Source Size Source Size is used to show the capacity of the source. Choose option 5 from the menu: 5. Source Size Press ENT and the LCD will show the following info. HDD:Hitachi Size:232.9GB Then press ENT and the LCD will show the data's size info. HDD:Hitachi Data:200.9GB Secure Erase Secure Erase is used to wipe the data of the hard disk, it will erase all of HDD of duplicator (included Source HDD). Choose option 6 from the menu: 6. Secure Erase Press ENT to ac
Краткое содержание страницы № 14
Load Default Press ESC to return to the main menu then use the ENT button to select. This function resets all settings to their factory default. This function helps the system recover from errors caused by an illegal operation. 10-07.Adv Setup Load Default Press ENT to enter the following screen. Use the Up and Down bu defaults. Load Default If Load Default OK, this will be displayed on the LCD as shown below. Load Default Ok Link Option NOT AVAILABLE USB Auto-Link NOT AVAILABLE Copy H
Краткое содержание страницы № 15
Basic Troubleshooting LCD If the LCD blank after the device is turned on, check that the power cable is properly connected and that the power supply is on. Error Message When the system is running a copy operation or hardware diagnostics, if the operation is manually terminated by pressing ESC an error message will be shown by the LCD. This may lead to an illegal operation and cause the device to stop reminding. If this happens, the device must be restarted. Hard Disk If unable to read the
Краткое содержание страницы № 16
Error Messages List NO# Error Messages Description Applied to 1 Source Drive Not Exist! Copy, Async Copy, Compare, No source HDD exist during operating Async Compare, PreScan Source, Source Size, Copy Size, Tolerance Size 2 User Abort! Cancel operating Any function and any time 3 No Drive Exist Device Info No HDD exist during operating 4 X Space Not Enough When source capacity is Copy, Compare Target Drive Space Not small than target Enough 5 X Space Not Enough When source capacity is Async
Краткое содержание страницы № 17
Firmware Update Procedure (Requires one hard drive containing the rmware le): 1. Create a 50MB HDD partition with FAT/FAT32 or NTFS les system on any SATA hard drive 2. Download the rmware and unzip the le to .BIN le format 3. Copy the .BIN le onto the 50 MB partition of the HDD 4. Insert this drive to the Source slot of the duplicator. For subsystem, connect the drive to the Source SATA port 5. Select "Firmware Update" function under the "Setup" or "Advanced Setup" menu and pre
