Краткое содержание страницы № 1
Product Manual
Lyrion Series CE-ATA
ST760211CA
ST730212CA
100441950
Rev. A
May 2008
Краткое содержание страницы № 2
Revision history Revision Date Sheets affected or comments Rev. A 05/22/08 Initial release. Copyright © 2008 Seagate Technology LLC. All rights reserved. Printed in U.S.A. Publication number: 100441950, Rev. A May 2008 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Lyrion Series, SeaTools and SeaTDD are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated com
Краткое содержание страницы № 3
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.2 Drive care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.0 Drive specifications . . . . . . . . . . . . . . . .
Краткое содержание страницы № 4
ii Lyrion CE-ATA Product Manual, Rev. A
Краткое содержание страницы № 5
List of Figures Figure 1. Lyrion Series (CE-ATA interface) disc drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Figure 2. Typical 3.3V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 3. Location where tri-axial accelerometer will be placed on Lyrion Series drives. . . . . . . . . . . . 12 Figure 4. Drive axis definition for Lyrion Series drives. . . . . . . . . . . . . . . . . . . . . . . . .
Краткое содержание страницы № 6
iv Lyrion CE-ATA Product Manual, Rev. A
Краткое содержание страницы № 7
1.0 Introduction ® This manual describes the functional, mechanical and interface specifications for the following Seagate ® Lyrion Series CE-ATA drives: • ST760211CA-60GB, ST730212CA-30GB disc drives with a CE-ATA interface. These drives provide the following key features. • 3,600-RPM spindle speed and a 2-Mbyte buffer combined for superior read/write performance. • Quiet operation. Fluid Dynamic Bearing (FDB) motor. • Perpendicular recording heads and EPRML technology, which provide the drives
Краткое содержание страницы № 8
1.1 Disclaimer Seagate Technology LLC makes no warranties whatsoever, including any warranty of merchantability, non- infringement, fitness for any particular purpose, or any warranty otherwise arising out of any proposal, specification or sample. Seagate may not be held liable for any direct, indirect, incidental, special, exemplary, or consequential damages (including, but not limited to, loss of use, data, or profits; procurement of substitute goods or services; or business interruptions)
Краткое содержание страницы № 9
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST760211CA and ST730212CA model drives. 2.1 Overview The specifications listed in this table are for quick reference. For details on specification measurement or definition, see the appropriate section of this manual. Table 1: Specifications Drive specification ST
Краткое содержание страницы № 10
Table 1: Specifications Drive specification ST760211CA ST730212CA Performance idle power (typical 3.3V) 0.68 W Low power idle power (typical 3.3V) 0.48 W Standby/Sleep power (typical 3.3V) 0.20 W Voltage tolerance (including noise) 3.3V ± 5% Ambient temperature 0° to 60°C (operating) –40° to 70°C (nonoperating) Temperature gradient (°C per hour max) 20°C (operating) 30°C (nonoperating) Relative humidity (noncondensing) 5% to 90% (operating) 5% to 95% (nonoperating) Relative humidity gradient
Краткое содержание страницы № 11
2.2 Formatted capacity Model Formatted Guaranteed Bytes per capacity sectors sector (logical) ST760211CA 60 Gbytes 117,210,240 512 ST730212CA 30 Gbytes 58,605,120 512 LBA mode addressing When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above. 2.3 Default logical geometry Model Cylinders Heads Sectors ST760211CA 116,280 16 63 ST730212CA 58,149 16 63 Lyrion CE-ATA Product Manual, Rev.
Краткое содержание страницы № 12
2.4 Recording and interface technology Technology Specification Interface CE-ATA Recording method Perpendicular Magnetic Recording Recording density BPI (bits/inch average) 1,025,000 Track density TPI (tracks/inch average) 165,000 2 Areal density (Gbits/inch average) 169 Spindle speed (RPM) (± 0.2%) 3,600 Internal data-transfer rate OD (Mbits/sec max) 350 Sustained data transfer rate OD @ 8bit/52MHz (Mbytes/sec) 24.5 Sustained data transfer rate OD @ 8bit/26MHz (Mbytes/sec) 18.0 Cache buffer (Mb
Краткое содержание страницы № 13
2.7 Power specifications The drive receives DC power (+3.3V) through the ZIF connector (CE-ATA interface). 2.7.1 Power consumption Power requirements for the drives are listed in the table on page 8. Typical power measurements are based on an average of drives tested, under nominal conditions, using +3.3V input voltage at 25°C ambient temperature. • Startup mode Startup power is measured from the time of power-on to the time that the drive spindle reaches operating speed. • Seek mode During see
Краткое содержание страницы № 14
Table 2: DC power Power Consumption at 3.3V Average (W) Startup (max*) 1.15 Read 1.19 Write 1.09 Performance idle (typical) 0.68 Low power idle (typical) 0.48 Standby/Sleep (typical) 0.20 *Maximum is the average of the peak value in 10 msec window 2.7.1.1 Typical current profile 100mA/div Sequential Motor Read Unload Spinup to Average Ready Performance Idle Standby Standby Load Average +3.3V Input Supply Current 1s/div Figure 2. Typical 3.3V startup and operation current profile 8 Lyrion CE-
Краткое содержание страницы № 15
2.7.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +3.3 volt line. Using 3.3-volt power, the drive is expected to operate with a maximum of 70 mV peak-to-peak square-wave injected noise at up to 20 MHz. Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current. 2.7.3 Voltage tolerance Voltage tolerance (including noise): 3.3V ± 5% Lyrion CE-ATA Product Manu
Краткое содержание страницы № 16
2.7.4 Power-management modes The drive provides programmable power management to provide greater energy efficiency. The drive features the following power-management modes: Table 3: Power-management modes Power modes Heads Spindle Buffer Active (read/write/seek) Tracking Rotating Enabled Idle, performance Tracking Rotating Enabled Idle, low power Parked Rotating Disabled Standby/Sleep Parked Stopped Disabled • Active mode The drive is in Active mode during the read/write and seek operations. •
Краткое содержание страницы № 17
2.8 Environmental specifications 2.8.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 70°C (158°F) within the operating ambient conditions. Case temperature of the drive operating at 60°C ambient may hit a maximum of 70°C at certain parts of the casing. Above 1,000 feet (305 meters), the maximum operating temperature is derated linearly by 1°C every 1000 feet. Operating
Краткое содержание страницы № 18
2.8.5 Shock All shock measurements in this section are carried out at drive level. For all linear shock test, operating or nonoperating, the input shock level is measured at the frame of the drive at the specific location as indicated in Figure 3 below. Figure 3. Location where tri-axial accelerometer will be placed on Lyrion Series drives All shock test cover all the 6 directions, +/- x, y and z axes. The drive axis definition in shown in Figure 4 below. Figure 4. Drive axis definition for Ly
Краткое содержание страницы № 19
2.8.6.1 Operating sweep sine vibration The following lists the maximum operating sweep sine vibration levels that the drive may experience while meeting the performance standards specified. It consists of a forward and backward sweep from 10 Hz to 500 Hz to 10 Hz. The drive operates without a hard error while being subjected to the following vibration levels. 10 Hz to 500 Hz @ 2 oct/min 1.0 Gs (0 to pk). Maximum displacement may apply below 10 Hz. 2.8.6.2 Operating random vibration The test co
Краткое содержание страницы № 20
2.8.6.4 Nonoperating random vibration The test consists of 15 minutes of random vibration using the power spectral density (PSD) levels specified in the table below. The vibration test level is 3.01 Gs RMS. The drive does not incur any physical damage when subsequently put into operation. Table 5: Nonoperating random vibration profile. 2 Frequency (Hz) G /Hz 2.5 1.0 x E-03 5 3.0 x E-02 40 1.8 x E-02 500 1.8 x E-02 2.8.7 Corrosive environment Seagate electronic drive components pass accelerated
