Краткое содержание страницы № 1
AF-S155NX
N
Краткое содержание страницы № 2
Краткое содержание страницы № 3
Краткое содержание страницы № 4
Please read ALL instructions before installing. Two people are recommended to install this product. If a new electrical outlet WINDOW SASH SEAL is required, have the outlet installed by a qualified electrician before installing unit. See#5 in Preliminary Instructions SAFETY LOCK AND 3/4" LONG HEX HEAD following. SCREW Preliminary instructions TOP ANGLE FOAM GASKET Do the following before starting to install unit. See illustrations WASHER HEAD LOCKING SCREW below. FRAME ASSEMBLY Check dimensions
Краткое содержание страницы № 5
4. CHECK FOR ANYTHING THAT COULD BLOCK Tools Required AIRFLOW - check area outside of window for things such as shrubs, trees, or awnings. Inside, be sure a large flat blade screwdriver tape measure furniture, drapes, or blinds will not stop proper air flow. adjustable wrench or pliers pencil 5. Check the available electrical service - power supply must Level be the same as that shown on the unit serial nameplate. Socket wrenches Power cord is 48"long. Be sure you have an outlet near. Phillips
Краткое содержание страницы № 6
Install Top Angle 2 and Side Bracket 1. Attach foam gasket to top angle above holes as 1 Remove Chassis shown in FIG. 6. 1. Pull down front panel and remove filter. (See FIG. 1). FIG. 6 2. Lift front upwards and place to one side. FIG. 1 FIG. 2 2. Install top angle and side retainers to cabinet as shown in FIG. 6. 3. Locate the four front screws and remove. These screws will be needed to re-install the front later. (See FIG.2) 4. Pry away front from cabinet sides as per photo (see F
Краткое содержание страницы № 7
3. Insert top and bottom legs of window filler panel frame Install Support 5 into channel in the to angle and bottom rail. Do both Bracket sides. 1. Hold each support bracket flush against outside of sill, 4. Insert washer head locking screws (2) into holes in and tight to bottom of cabinet as shown below. Mark top leg of filler panel frame (see Step 6). Do not totally brackets at top level of sill, and remove. tighten. Allow leg to slide freely. Screws will be tightened after Section 6. P
Краткое содержание страницы № 8
Install Chassis into Extend Window Filler 8 6 Cabinet and Install Panels Front to Unit 1. Carefully raise window to expose filler panel locking 1. Lift air conditioner and carefully slide into cabinet screws. Loosen screws so filler panels slide easily. leaving 6" protruding. 2. DO not push on controls OR finned coils. 3. Be sure chassis is firmly seated towards rear of cabinet. LOCKING SCREWS 4. Installation of front is the reverse of removal outlined in Section 1. 2. Extend panels to fil
Краткое содержание страницы № 9
Краткое содержание страницы № 10
Краткое содержание страницы № 11
Краткое содержание страницы № 12
TO CHANGE TEMPERATURE SETTING: YOU WILL SEE: DO THIS: PRESS TO RAISE PRESS TO LOWER Note: Tap or hold either up ( ) or down ( ) button until the desired temperature is seen on the display. This temperature will be automati- o o o o cally maintained anywhere between 60 F (16 C) and 90 F (32 C) for cooling mode. If you want the display to read the actual room temperature. See "To Operate on Fan " section on Page 13. TO ADJUST FAN SPEEDS: YOU WILL SEE : DO THIS: PRESS TO SELECT: FASTER SLO
Краткое содержание страницы № 13
TO OPERATE ON FAN: YOU WILL SEE: LIGHT On DO THIS: PRESS MODE BUTTON CHOOSE FAN Note: Use this function only when cooling is not desired, such as for room air circulation or to exhaust stale air. (Remember to open the vent during this function, but keep it closed during cooling for maximum cooling efficiency.) You can choose any fan speed you prefer. (Exc- ept "Auto Cool"). During this function, the display will show the actual room temperature, not the set temperature as in the cooling mode. TO
Краткое содержание страницы № 14
FAULT CODES TO TURN UNIT OFF: DO THIS: PRESS POWER ON/OFF If the display reads "ES" or "AS", a sensor has failed. Contact your Authorized SHARP Service Center. Fresh Air Vent Control The Fresh Air Vent allows the air conditioner to: 1. Recirculate inside air - Vent Closed (see Fig. 1) 2. Draw fresh air into the room - Vent Open (see Fig. 2) 3. Exchange air from the room and draws fresh air into the room - Vent and Exhaust Open (see Fig. 3) Fig. 1 (OFF) Fig. 3 (VENT) Fig. 2 (FRESH AIR) The louve
Краткое содержание страницы № 15
Краткое содержание страницы № 16
Краткое содержание страницы № 17
Краткое содержание страницы № 18
Краткое содержание страницы № 19
Краткое содержание страницы № 20
66129901273
