Краткое содержание страницы № 1
CRX - 160E
CD-R/RW Drive Unit
CRX - 160E
CD-R/RW Drive Unit
User’s Guide
Revision 1.1
©2000 by Sony Australia.
User’s Guide
Краткое содержание страницы № 2
Owner’s Record This unit uses CD-RW discs with the following mark. The model and serial numbers are located on the top of the drive. Record these numbers in the spaces provided below. Refer to them whenever you call upon your sales repre- sentative regarding this product. Model No. Serial No. This unit uses CD-R discs with the following mark. Safety Regulations This unit uses CD-ROM discs with the following mark. WARNING To prevent fire or s
Краткое содержание страницы № 3
Contents Introduction 6 Location and Function of Parts and Controls 7 Front Panel .........................................................................................7 Rear Panel..........................................................................................8 Precautions 9 System Setup 10 Installing the Drive in Your Computer 10 Preparation .......................................................................................10 Setting the Jumpers.................................
Краткое содержание страницы № 4
Introduction Location and Function of Parts and Controls Features Front Panel The CRX160E is an internal CD-R/RW (Compact Disc Recordable/ ReWritable) drive unit designed for use with personal computers. It conforms to the “MultiRead” specification. 1 2 General 1 • 5 / inch half-height drive form factor. 4 • Power loading and eject of a disc. • Housed in a casing with an airtight frame. • 4 Mbyte buffer memory. • Supports Power saving mode and Sleep mode. Supported disc formats • Reads and write
Краткое содержание страницы № 5
Rear Panel Precautions Pin 1 n Installation • Avoid placing the drive in a location subject to: –high humidity –high temperature –excessive dust –mechanical vibration –direct sunlight. We recommend to use the drive in a horizontal or vertical position. Do not use it in a tilted position. n Operation 1 2 3 4 5 • Do not move the drive during operation. This may cause it to malfunction during reading or writing. • Avoid exposing the drive to sudden changes in temperature as 1 Unused co
Краткое содержание страницы № 6
Setting the Jumpers System Setup Set the jumpers on the rear of the drive in accordance with the configuration of your computer system. To use this CD-R/RW device, the following components are required: The illustration below shows the jumpers set to the “MASTER” • Personal Computer with an IDE bus (ATA compliant) position, this is the default set by the factory. • IDE Interface cable (40 to 40 pin flat cable) • Software - Device driver (for reading discs only) - CSEL This is included with most
Краткое содержание страницы № 7
Opening the Computer Connecting the Drive The drive should be connected to the computer with the following Refer to your computers user manual for instructions on how to connectors: open the computer. • DC INPUT connector. • AUDIO OUT connector (if you plan to connect audio equipment). • IDE INTERFACE connector. IDE INTERFACE Connector DC INPUT connector AUDIO OUT connector n DC INPUT connector The pin assignment for the DC connector is as follows. Mounting the Drive GND Do not mount the drive a
Краткое содержание страницы № 8
n IDE INTERFACE connector 1 Firmly insert one end of the interface cable into the INTER- n Frame ground FACE CONNECTOR. When installed the CD writer unit should have its metal chasis in contact with a grounded metal area of the computers frame. Pin 1 This normally occurs naturally when the drive is mounted into one of the computers spare drive bays. INTERFACE CONNECTOR INTERFACE cable 2 Attach the other end of the cable to the PRIMARY or SECONDARY IDE interface connectors on the computers mainbo
Краткое содержание страницы № 9
Using Discs Installing the Software Storing Discs To use the drive as a CD-Rom Reader. • Do not store the disc in a location subject to: Windows 95, 98, NT 4.0, 2000 or Macintosh systems should –high humidity detected the drive at start up and the appropriate ATAPI drivers be –high temperature installed automatically. –excessive dust If you wish to use the drive with MS-DOS you will require the –direct sunlight MSCDEX extension (available from Microsoft) and Sony’s ATAPI device driver (available
Краткое содержание страницы № 10
Operating the Drive Note: This section describes how to start the drive and eject a disc. When the drive is set up in vertical position, use the disc locks to prevent your disc from falling. See “How to Use the Disc Locks” on page 21 for details. Starting the Drive Disc locks 1 Turn on the power of your computer. 2 Press the eject button. The tray comes out automatically. 4 Gently push the tray or press the eject button to close the tray. The drive will begin reading the Table of Contents (TOC)
Краткое содержание страницы № 11
Ejecting the Disc How to Use the Disc Locks To eject the disc, press the eject button on the front panel. The tray The disc tray has four disc locks that prevent the disc from falling comes out automatically. when the drive is set up in vertical position. Disc locks Note: The eject button does not work if it is disabled by the software you Note: are using. When the drive is used in horizontal position, you do not need to lock the disc. n Opening the tray manually in an emergency You can open the
Краткое содержание страницы № 12
Specifications When the drive’s right side is down n General To facilitate disc handling, set the disc locks B, C and D into the Host interface ATAPI compliant locked position, and leave the disc lock A in the unlocked position. Read Function This drive conforms to the “Multiread” specification. Acceptable discs: CD-ROM data (mode-1) CD-ROM XA (mode 2, form 1 & 2) CD-Digital Audio Audio-combined CD-ROM Top side CD-I (mode 2, form 1 & 2) CD-I Ready Photo CD (Single and Multi session) Video CD Ri
Краткое содержание страницы № 13
n Drive performance n Dimensions and weight Dimensions 146.0 x 41.4 x 203 mm ( w / h / d ) Data transfer rate Mass 920 g Sustained rate: 150 Kbytes/s mode 1 (1X) 300 Kbytes/s mode 1 (2X) n Power requirement 600 Kbytes/s mode 1 (4X) Voltage +5 V ± 5 % DC and +12V DC ± 10 % 1200 Kbytes/s mode 1 (8X) 1800 kbytes/s mode 1 (12X) Sleep +5 Vdc 150 mA (Typical) 2000 to 4800 Kbytes/s mode 1 < 200 mA (Max) (13 to 32X CAV) +12 Vdc 0.2 mA (Typical) < 0.3 mA (Max) 171.1 Kbytes/s mode 2 (1X) 342.2 Kby
