Краткое содержание страницы № 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
POWERHOUSE CLUB
Hardware Identifier
Assembly Instruction PWR 6
Parts List
Warranty
Ordering Parts
Model
PWR 6
Retain This
Manual for
Reference
06-30-03
OWNER'S
IMPEX FITNESS PRODUCTS
MANUAL
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.c
Краткое содержание страницы № 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE PACK……….....…....................................................................... 3 ASSEMBLY INSTRUCTIONS........................................................................... 5 EXPLODED DIAGRAM.........................................................
Краткое содержание страницы № 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one perso
Краткое содержание страницы № 4
HARDWARE PACK 3
Краткое содержание страницы № 5
HARDWARE PACK 4
Краткое содержание страницы № 6
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Main Frame (#1) to the Front & Rear Stabilizers (#2 & 3). Secure each end with two M10 x ¾” Allen Bolts (#36) and ∅ ¾” Washers (#42). Attach a Lock Knob (#23) to the hole underneath the Main Frame. B.) Slide the Sliding Block (#8)
Краткое содержание страницы № 7
STEP 2 (See Diagram 2) A.) Attach four Bushings (#27) to a Seat Support Frame (#6). B.) Attach a Backrest Support (#7) to the rear of the Seat Support Frame (#6). Align the holes and secure them with one M10 x 1 ¾” Allen Bolt (#37) and ∅ ¾” Washer (#42). Repeat the same procedure to install the other side. C.) Attach two Bushings to the pivot on the Sliding Block (#8). Attach two Bushings to each Backrest Supports (#7). Align the holes and secure them with one M10 x 6 ¾” Allen Bolt
Краткое содержание страницы № 8
STEP 3 (See Diagram 3) A.) Place the Backrest Board (#14) onto the Backrest Supports (#7). Secure it with four M8 x 2” Allen Bolts (#40) and ∅ 5/8” Washers (#43). B.) Place the Seat Pad (#13) onto the Seat Support Frames (#6). Secure it with four M8 x 2” Allen Bolts (#40) and ∅ 5/8” Washers (#43). DIAGRAM 3 7
Краткое содержание страницы № 9
STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#5) to the open bracket on the Main Frame (#1). Secure it with an Axle (#17), two M10 x ¾” Allen Bolts (#36), and two ∅ ¾” Washers (#42). B.) Insert one Foam Tube (#10) halfway through the hole on the Main Frame. Insert two Foam Tubes halfway through the holes on the Leg Developer (#5). Push six Foam Rolls (#24) onto the Tubes from both ends. Plug six Foam Roll End Caps (#25) into the Tubes. C.) Slide the Olympic Sleeve (#20) o
Краткое содержание страницы № 10
STEP 5 (See Diagram 5) A.) Attach the Arm Curl Pad (#15) to the Arm Curl Stand (#4). Secure it with two M8 x 5/8” Allen Bolts (#41) and two ∅ 5/8” Washers (#43). Insert the Arm Curl Stand into the front opening on the Main Frame (#1). Use the Lock Knob to hold the desired Arm Curl height. B.) Attach the Curl Bar Support Frame (#11) to the open bracket on the Leg Developer (#5). Lock it with a L-shaped Pin (#21). C.) Remove the Pin, Curl Bar Handle and Arm Curl when using the Leg D
Краткое содержание страницы № 11
STEP 6 (See Diagram 6) A.) Attach an Upright Beam (#49) to a Floor Stabilizer (#47). Secure it with two M10 x 2 3/4” Carriage Bolts (#81), ∅ ¾” Washers (#42), and M10 Aircraft Nuts (#44). Do not tighten the nuts and bolts yet. B.) Attach the upper end of Left Support (#50) to the Upright Beam. Secure it with one M10 x 5/8” Allen Bolt (#88) and ∅ ¾” Washer (#42). C.) Attach the lower end of Left Support (#50) to the Floor Stabilizer (#47). Attach one end of the Rear Stabilizer (#53) to t
Краткое содержание страницы № 12
STEP 7 (See Diagram 7) A.) Attach the Front Vertical Frame (#54) to the Rear Stabilizer (#53). Secure it with two M10 x 5/8” Allen Bolts (#88) and ∅ ¾” Washers (#42). Do not tighten all the nuts and bolts yet. B.) Attach the Cross Brace (#48) to the Left & Right Supports (#50 & 51). Secure each end of Cross Brace with two M10 x 3 1/8” Carriage Bolts (#82), one 5” x 1 5/8” Bracket (#64), two ∅ ¾” Washers (#42), and two M10 Aircraft Nuts (#44). C.) Attach the Rear Vertical Frame (#52) to th
Краткое содержание страницы № 13
STEP 8 (See Diagram 8) A.) Slide the Sliding Weight Post (#56) onto the Rear Vertical Frame (#52). Slide the Sliding Pulley Bracket (#57) onto the Front Vertical Frame (#54). Use a Lock Knob (#23) to hold the Sliding Pulley Bracket in position. B.) Insert the Upper Frame (#55) into the top opening on the Front Vertical Frame (#54). Attach the rear end of Upper Frame to the Rear Vertical Frame. C.) Secure the Upper Frame with two M10 x 5/8” Allen Bolts (#88) and ∅ ¾” Washers (#42). Secure
Краткое содержание страницы № 14
CABLE LOOP DIAGRAM 13
Краткое содержание страницы № 15
STEP 9 (See Diagram 9 & Cable Loop Diagram) A.) Attach the 100” Upper Cable (#68) to the opening on the front Upper Frame (#55). Make sure the ball stopper of the Cable is under the Frame. B.) Attach a Pulley (#70) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#85), two 5/8” Pulley Bushings (#79), and one M10 Aircraft Nut (#44). C.) Draw the Cable along the Upper Frame towards the back of the machine to the opening on the Upper Frame. Repeat Step B above to install a Pulley.
Краткое содержание страницы № 16
STEP 10 (See Diagram10 & Cable Loop Diagram) A.) Attach the 268” Lower Cable (#69) to the Sliding Pulley Bracket (#57). Attach two Small Pulleys (#71) to the Brackets. Secure them with two M10 x 1 ¾” Allen Bolts (#86), four ∅ ¾” Washers (#42), and two M10 Aircraft Nuts (#44). B.) Draw the Cable upward to the opening on top of the Front Vertical Frame (#54). Attach a Pulley (#70) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#85), two 5/8” Pulley Bushings (#79), and one M
Краткое содержание страницы № 17
DIAGRAM 10 16
Краткое содержание страницы № 18
17
Краткое содержание страницы № 19
18
Краткое содержание страницы № 20
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Main Frame 1 51 Right Support 1 2 Front Stabilizer 1 52 Rear Vertical Frame 1 3 Rear Stabilizer 1 53 Rear Stabilizer 1 4 Arm Curl Stand 1 54 Front Vertical Frame 1 5 Leg Developer 1 55 Upper Frame 1 6 Seat Support Frame 2 56 Sliding Weight Post 1 7 Backrest Support 2 57 Sliding Pulley Bracket 1 8 Sliding Block 1 58 Left Safety Catch 1 9 Incline Adjustment Bar 1 59 Right Safety Catch 1 10 Foam Tube 3 60 Chrome Panel 2 11 Cu
