Краткое содержание страницы № 1
MODEL W1777
1
2 ⁄ 2" 16 GAUGE
FINISH NAILER
OWNER'S MANUAL
Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz
COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC., REVISED DECEMBER, 2007 (JM)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#9552TS Printed in China
Краткое содержание страницы № 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/equipment. Failure to read, understand, and follow the instructions given in this manual may result in serious personal injury, including amputation, electrocution, or death. The owner of this machine/equipment is solely responsible for its safe use. This responsibility includes, but is not limited to, proper installation in a safe environment, personnel training and usa
Краткое содержание страницы № 3
1 Model W1777 2 ⁄2" 16 Gauge Finish Nailer SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for
Краткое содержание страницы № 4
1 Model W1777 2 ⁄2" 16 Gauge Finish Nailer Safety Instructions for Pneumatic Tools 10. USE PROPER AIR HOSE for the 17. DISCONNECT TOOLS before tool. Make sure your air hose is in servicing, changing accessories, or good condition and is long enough moving to another location. to reach your work without 18. DO NOT OVERREACH. Keep proper stretching. footing/balance at all times. 11. WEAR PROPER APPAREL. Do 19. USE THE RECOMMENDED not wear loose clothing, gloves, ACCESSORIES. Consult owne
Краткое содержание страницы № 5
1 Model W1777 2 ⁄2" 16 Gauge Finish Nailer Additional Safety for Nailers/Staplers 1. HAND INJURIES: Do not place your 5. HOSE USAGE: Make sure your air hands near the nail point of entry. hose is designed for the tool in A nail can deflect and tear through use, is in good condition, and is the surface of the workpiece, long enough to reach your work puncturing your hand or fingers. without stretching. However, an overly long air hose in the work 2. COMBUSTIBLE GASES: Never area may be a
Краткое содержание страницы № 6
1 Model W1777 2 ⁄2" 16 Gauge Finish Nailer INTRODUCTION Woodstock Technical Tool Data Support Nail Size ............................. 16 Gauge 1 1 Nail Length ..........................1 ⁄4"–2 ⁄2" 1 This Model W1777 2 ⁄2" 16 Gauge Finish Magazine Capacity ...................74 Nails Nailer has been specially designed to pro- 1 Air Inlet ................................ ⁄4" NPT vide many years of trouble-free service. Weight ....................................5 lbs. Close attention to det
Краткое содержание страницы № 7
1 Model W1777 2 ⁄2" 16 Gauge Finish Nailer Compressed Air System The Model W1777 is designed to be operated at 60-100 PSI using clean, dry, regulated, compressed air. Do not exceed the 120 PSI maximum operating pressure for your model. Before using your nailer, regulate the air pressure to find the optimum setting within the specified operating range. Start by testing the nailer at a low setting, then increase the air pressure as Exceeding the maximum permissible needed for satisfact
Краткое содержание страницы № 8
1 Model W1777 2 ⁄2" 16 Gauge Finish Nailer SETUP Unpacking This finish nailer has been carefully packaged for safe transportation. If you notice the tool has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Inventory The following is a description of the main components shipped with the Model W1777. Lay the components out to inventory them. Note: If you can't find an item on this list, check the mounting location on the tool or examine the packagin
Краткое содержание страницы № 9
1 Model W1777 2 ⁄2" 16 Gauge Finish Nailer — If the nailer fires when the trigger Safety Nose Mechanism is pulled, without the safety nose A safety mechanism on the nose of mechanism being depressed, then the nailer protects against accidental the nailer is not working properly. firing. When the trigger is pressed, the nailer will not fire until the safety nose — If you find that the safety mechanism is depressed. nose mechanism is not working properly, check the lubrication of Before y
Краткое содержание страницы № 10
1 Model W1777 2 ⁄2" 16 Gauge Finish Nailer OPERATIONS Loading When replacing nails in your Model W1777, follow these guidelines: Gauge: ........................................16 1 1 Length: ..............................1 ⁄4"–2 ⁄2" Capacity: .....................................74 To load your nailer, do these steps: Figure 3. Loading nails into magazine. 1. DISCONNECT NAILER FROM THE AIR 4. Slide the nails all the way down to SUPPLY! the nose of the nailer. 2. Grip the nailer firmly, an
Краткое содержание страницы № 11
1 Model W1777 2 ⁄2" 16 Gauge Finish Nailer 3. Depress the safety nose mechanism Adjusting Depth against your workpiece. A depth adjustment knob is attached to 4. Before pulling the trigger, make sure the nose for setting the nail depth. your free hand and other body parts are positioned out of the way of a To adjust the nail depth, do these potential path of a nail in case of steps: deflection. 1. DISCONNECT NAILER FROM THE AIR Deflection is caused when grain SUPPLY! irregularities, kn
Краткое содержание страницы № 12
1 Model W1777 2 ⁄2" 16 Gauge Finish Nailer Clearing Jammed Nails Nose Release Nose A jammed nail must be cleared before Tip using the nailer again. To clear a jammed nail from the dis- charge area, do these steps: 1. DISCONNECT NAILER FROM THE AIR Nose Cover SUPPLY! Figure 6. Nose opened to clear jam. 2. Pull back and latch the magazine 5. Remove the jammed nail with a pusher. tool that will fit in the slot on the underside of the nose, like needle 3. Remove the nail stick from the n
Краткое содержание страницы № 13
1 Model W1777 2 ⁄2" 16 Gauge Finish Nailer 6. Open the nose cover as if to clear a Replacing Pistons/ jammed nail. O-Rings 7. Watch the discharge area and push Under heavy use, a piston or piston shaft the top of the piston with your may wear out. Replacement is quick finger. You will see the piston shaft and easy. Contact your authorized Shop slide down the discharge area. Fox dealer to obtain the Piston Repair Kit (Part Number X1777095), or the 8. Taking care not to scratch or dent
Краткое содержание страницы № 14
1 Model W1777 2 ⁄2" 16 Gauge Finish Nailer CLEANING & LUBRICATION Cleaning Lubricating Use a good solvent to clean the nose Standard pneumatic tool oil has been assembly of the nailer. Always be sure included with your new Shop Fox nailer that the nailer is dry before using it to help maintain its useful life. Place two again. to six drops of oil in the nailer air inlet (as shown in Figure 7) before every use, Do not allow dust, chips, sand, etc. or after 2 hours of continuous use. into
Краткое содержание страницы № 15
1 Model W1777 2 ⁄2" 16 Gauge Finish Nailer W1777 PARTS BREAKDOWN -13- �� � �� � � �� �� �� � �� � �� �� � � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� ��
Краткое содержание страницы № 16
1 Model W1777 2 ⁄2" 16 Gauge Finish Nailer W1777 PARTS LIST REF PART � # DESCRIPTION REF PART � # DESCRIPTION 1 XPAW05M HEX �WRENCH �5MM 49 X1777049 STEEL � BALL � DW=2 2 XPAW04M HEX �WRENCH �4MM 50 X1777050 SPECIAL �SCREW 3 X1777003 CARRYING � CASE 51 X1777051 S UP P OR T � B RA C KE T 4 X1777004 AIR �PLUG � COVER 52 X1777052 CONNECTING � BRACKET 5 X1777005 AIR � PLUG 53 X1777053 ROLL � PIN � 3 � X �28 6 X1777006 END �CAP 54 X1777054 O-RING � 2 � X �2.5 7 X1777007 END �CAP �GASKET 55 X1777055
Краткое содержание страницы № 17
1 Model W1777 2 ⁄2" 16 Gauge Finish Nailer Troubleshooting Symptom Possible Cause Possible Solution Air leaking at 1. O-rings in trigger valve 1. O-rings must be replaced trigger valve area. housing are damaged. & operation of safety nose must be checked. Air leaking between 1. Loose screws in housing. 1. Tighten screws. housing and hose 2. Damaged O-ring. 2. Replace O-ring 3. Loose air fitting. 3. Tighten air fitting & use teflon tape. Air leaking between 1. Damaged seal. 1. Replace damage
Краткое содержание страницы № 18
� � � � � � � �� � � �� � � � � � � � � � � � � � � ��� � � � � � � � � � � � � � �� � � � �� � � � � � � � �� � � �� � � � � � � � � �� � � ��� � � � �� � �� � �� � � � �� � �� � � � � � � �� � � � �� � � � � � � � � � ��� � � �� � � � � � � � � �� � � �� �� � � � � � �� � �� �� � � � �� � � � �� � � �� � � � �� � �� � � � � �� � �� � � � �� � � � �� � � �� � � � � � � � � �� � � � � �� � � � �� � � � � � � � �� � � � � �� � � �� � � � � � �� � � �� � � � �� � � �� � � � � �� � � ��� � � �� � �
Краткое содержание страницы № 19
Warranty Registration Name ___________________________________________________________________________________ Street __________________________________________________________________________________ City _________________________ State ___________________________Zip ________________________ Phone # ______________________ Email __________________________Invoice # ___________________ Model #_________Serial #______________Dealer Name__________________Purchase Date___________ The following informa
Краткое содержание страницы № 20
FOLD ALONG DOTTED LINE Place Stamp Here WOODSTOCK INTERNATIONAL INC. P.O. BOX 2309 BELLINGHAM, WA 98227-2309 FOLD ALONG DOTTED LINE TAPE ALONG EDGES--PLEASE DO NOT STAPLE
