Краткое содержание страницы № 1
MODEL D3736
Palm Finishing Sander
OWNER'S MANUAL
Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz
COPYRIGHT © MARCH, 2008 BY WOODSTOCK INTERNATIONAL, INC.,
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#10536BL Printed in China
Краткое содержание страницы № 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/equipment. Failure to read, understand, and follow the instructions given in this manual may result in serious personal injury, including amputation, electrocution, or death. The owner of this machine/equipment is solely responsible for its safe use. This responsibility includes, but is not limited to, proper installation in a safe environment, personnel training and usa
Краткое содержание страницы № 3
Model D3736 Palm Finishing Sander SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper acc
Краткое содержание страницы № 4
Model D3736 Palm Finishing Sander 7. ONLY ALLOW TRAINED AND 15. KEEP WORK AREA CLEAN AND PROPERLY SUPERVISED WELL LIT. Clutter and dark PERSONNEL TO OPERATE shadows may cause accidents. MACHINERY. Make sure operation 16. REMOVE ADJUSTING KEYS AND instructions are safe and clearly WRENCHES. Make a habit of understood. checking for keys and adjusting wrenches before turning 8. KEEP CHILDREN AND VISITORS machinery ON. AWAY. Keep all children and visitors a safe distance from the 17. CHE
Краткое содержание страницы № 5
Model D3736 Palm Finishing Sander Additional Safety Instructions for the Palm Finishing Sander 1. HAND PROTECTION. DO NOT place 4. TRANSPORTING: DO NOT carry a hands near, or in contact with, plugged-in sander with your finger sanding base during operation. on the ON/OFF switch. Do not carry Sandpaper has the capability of the sander by the power cord. removing skin. 5. VIBRATION GENERATED INJURIES: 2. INSPECTING WORKPIECES. Limit prolonged exposure to this Always inspect workpiece f
Краткое содержание страницы № 6
Model D3736 Palm Finishing Sander INTRODUCTION Woodstock Technical Tool Data Support Voltage ....................................110V Amps ........................................... 2 This Model D3736 Palm Finishing Sander Vibrations Per Minute ................ 10,000 has been specially designed to provide 1 1 1 Sandpaper Size .....4 ⁄4" x 4 ⁄2" ( ⁄4 Sheet) many years of trouble-free service. Close 1 Weight .................................3 /2 lbs. attention to detail, ruggedly built parts
Краткое содержание страницы № 7
Model D3736 Palm Finishing Sander SETUP Unpacking This sander has been carefully packaged for safe transportation. If you notice the tool has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Inventory The following is a description of the main components shipped with the Model D3736. Lay the components out to inventory them. Note: If you can't find an item on this list, check the mounting location on the tool or examine the packaging materials carefu
Краткое содержание страницы № 8
Model D3736 Palm Finishing Sander OPERATIONS Aluminum oxide and silicon carbide Getting Started abrasives are an excellent choice because they last longer and are sharper than To test the sander, do these steps: natural abrasives. 1. Plug the cord into a 110V outlet. Attaching Abrasives 2. Move the switch (located at the front of the sander) to the “—” position to If you have not read the safety turn the sander ON, and move the instructions in this manual, do not switch to the “O” pos
Краткое содержание страницы № 9
Model D3736 Palm Finishing Sander Tip: Try using the sandpaper that Using the Sander came with your sander as a template 1 Determine the appropriate grit size for for cutting holes in new ⁄4 sheets your project and sand the work evenly to match those on the bottom of the in the same direction as the grain of the sander—so the dust bag can collect wood. Always keep the sander moving so dust particles. Use a paper punch the finish of your work stays consistent. to cut the holes; or mar
Краткое содержание страницы № 10
Model D3736 Palm Finishing Sander MAINTENANCE General Keeping Tool Clean Regular periodic maintenance on your Your Model D3736 Palm Finishing Sander Model D3736 Palm Finishing Sander will will give you years of trouble free service ensure its optimum performance. Make if you keep it clean and free of built-up a habit of inspecting your sander each dust or grime. Ensure that no air passages time you use it. Check for the following get blocked. If they do, blow them out conditions and repair
Краткое содержание страницы № 11
Model D3736 Palm Finishing Sander D3736 PARTS BREAKDOWN -9-
Краткое содержание страницы № 12
Model D3736 Palm Finishing Sander D3736 PARTS LIST REF PART # DESCRIPTION REF PART # DESCRIPTION 1 XD3736001 TOP HOUSING COVER 18 XD3736018 DUST BAG 2 XD3736002 LEFT HOUSING 19 XD3736019 DUST BAG BRACKET 3 XD3736003 RIGHT HOUSING 20 XD3736020 BRUSH BOX 4 XD3736004 STATOR 21 XD3736021 CARBON BRUSH 5 XD3736005 ROTOR 22 XD3736022 BRUSH HOLDER 6 XP609 BALL BEARING 609 23 XPHTEK39M TAP SCREW M4 X 12 7 XP627 BALL BEARING 627 24 XPHTEK6M TAP SCREW M4 X 16 8 XD3736008 ALUMINUM FAN 25 XPHTEK31M TAP SCREW
Краткое содержание страницы № 13
Model D3736 Palm Finishing Sander Troubleshooting Symptom Possible Cause Possible Solution Reduced amount of 1. Sandpaper clogged with paint 1. Replace sandpaper. material removed or glue. by sander, quality 2. Sandpaper grit dull. 2. Replace sandpaper of finish decreases, sander slides easily across workpiece. Sander generates 1. Dust bag full. 1. Empty dust bag. excessive dust 2. Holes on sandpaper not 2. Use abrasive paper with particles. aligned with holes in sander pre-punched holes tha
Краткое содержание страницы № 14
Краткое содержание страницы № 15
Warranty Registration Name ___________________________________________________________________________________ Street __________________________________________________________________________________ City _________________________ State ___________________________Zip ________________________ Phone # ______________________ Email___________________________Invoice # ___________________ Model #_________Serial #______________Dealer Name__________________Purchase Date___________ The following informa
Краткое содержание страницы № 16
FOLD ALONG DOTTED LINE Place Stamp Here WOODSTOCK INTERNATIONAL INC. P.O. BOX 2309 BELLINGHAM, WA 98227-2309 FOLD ALONG DOTTED LINE TAPE ALONG EDGES--PLEASE DO NOT STAPLE
