Руководство по эксплуатации Vision Fitness R2600HRT

Краткое содержание страницы № 1

Assembly
Guide
R2600HRT
COMMERCIAL FITNESS BIKE

Краткое содержание страницы № 2

Assembly Guide R2600HRT COMMERCIAL FITNESS BIKE To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order. Before proceeding, find your new Fitness Bike’s serial number located on the front axle tube, and enter here: Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Fitness Bike. If any parts, hardware or tools are missing,

Краткое содержание страницы № 3

TOOLS & PARTS INCLUDED 5mm Allen Wrench 15mmPedal Wrench 6mm Allen Wrench Screwdriver 4mm L-Shaped Wrench PARTS BOX Console Mast Cover Water Bottle Heart Rate Chest Strap Color-coded Hardware Bags Pedals/Straps Owner’s Guide Assembly Guide Warranty Card 5mm L-Shaped Wrench

Краткое содержание страницы № 4

HARDWARE INCLUDED ORANGE BAG GREEN BAG M8x65L Screw Quantity: 2 M8 Lock Washer M8 x 15L Screw Quantity: 8 Quantity: 4 M8 Lock Washer M8 x 20L Screw Quantity: 4 Quantity: 2 M8 x 20L Screw Quantity: 4 BLUE BAG BLACK BAG M8 Lock Washer M8 x 15L Screw Quantity: 6 Quantity: 7 M6 x 55L Screw Quantity: 8 PINK BAG M6 Lock Washer Quantity: 8 M8 Lock Washer M8 x 15L Screw Quantity: 2 Quantity: 2 YELLOW BAG M5 x 35L Screw M5 Lock Washer Quantity: 2 Quantity: 2

Краткое содержание страницы № 5

STEP 1 ORANGE BAG • Install the rear foot with the four lock washers (M8), two inside screws (M8x65L), and two outside screws (M8x20L). Tighten with the 5mm Allen wrench. STEP 1 STEP 2 BLUE BAG • Slide the console mast boot onto the console mast. • Unfold the wire harness and heart rate wires located in the console mast frame bracket. Attach the wire tie coming from the bottom of the console mast to the wire harness and heart Rear Foot rate wires. Pull the wire tie with wire harness and heart r

Краткое содержание страницы № 6

STEP 3 PINK BAG • Mount the upper handlebars to the console mast using two lock washers (M8) and two screws (M8x15L). Tighten with the 5mm Allen wrench. • Remove the four mounting screws from the back of the console. Connect the wire harness and heart rate wires that come from the console mast into the plugs located in the back of the console. Make sure the 9-Volt battery is plugged in and in place on the console. Attach the console to the mast with the four screws removed earlier. Console Mast

Краткое содержание страницы № 7

STEP 4 GREEN BAG • Attach the seat frame to the sliding seat bracket using four lock washers (M8) and four socket head cap screws (M8x20L) and the 6mm Allen wrench. • Connect Wires A on the seat handlebar to Wires B on the sliding seat bracket. Attach the seat handlebars to the sliding seat bracket using four lock washers (M8) and four screws (M8x15L). Tighten with the 5mm Allen wrench. Seat Handlebar Wires A Seat Frame STEP 4 Wires B Sliding Seat Bracket 7

Краткое содержание страницы № 8

STEP 5 BLACK BAG • Secure the Lumbar controlled seat back and the seat bottom to the seat frame with eight lock washers (M6) and eight screws (M6x55L). Tighten with the 4mm Allen wrench. • Snap the plastic seat cover into place on the back of the Lumbar controlled seat. Plastic Seat Lumbar Controlled Cover Seat Back Seat Bottom STEP 5 8

Краткое содержание страницы № 9

STEP 6 YELLOW BAG • Attach the left and right pedals to the left and right crank arms. Tighten the pedals using the 15mm Pedal Wrench. • Secure the Accessory Tray to the seat handlebar with two screws (M5x35L) and two lock washers (M5). Tighten with the screwdriver. Accessory Tray Pedal STEP 6 500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551 toll free 1.800.335.4348 • phone 1.920.648.4090 • fax 1.920.648.3373 www.visionfitness.com ©2004 Vision Fitness. All Rights Reserved. 9.0