Краткое содержание страницы № 1
Power Fogger Industrial Line
and PFI w/ LSG
Operator’s Manual
www.ultratecfx.com
VER. 30.10.10
Краткое содержание страницы № 2
Table of Contents Introduction ................................................................................ 3 Microprocessor Control ............................................................ 3 Water Base Fog Technology ...................................................... 3 Warning ...................................................................................... 3 Important Safety Instructions: ................................................... 3 Safety Precautions ................
Краткое содержание страницы № 3
Introduction The Power Fogger Industrial is a Microprocessor Controlled, Water Based Fog generating system. Microprocessor Control The PFI features dual microprocessor control. From temperature regulation to taper back flow control, all of the functions are monitored and processed by the two on-board processors. Water Base Fog Technology Water Base Fog technology is achieved by pumping a glycol/water mixture through a heat exchanger. This will vaporize the fluid as it passes through the hot un
Краткое содержание страницы № 4
PFI Technical Specifications Model: PFI/PFI-9D Part Number: PFI CLF 4450 / 120 volt CLF 4451 / 220-240 volt PFI-9D CLF 4460 / 110 volt CLF 4461 / 220-240 volt Power Rating: 120 Volt A.C. 50/60 Hz. 13 Amps. 240 Volt A.C. 50/60 Hz. 6.5 Amps. Fluid: Water Base Fog Fluid (Use only Ultratec Fluid) PFI Technical Drawings Power Fogger Industrial www.ultratecfx.com 4
Краткое содержание страницы № 5
Power Fogger Industrial 9D www.ultratecfx.com 5
Краткое содержание страницы № 6
LSG w/ PFI Technical Drawings LSG PFI System on a Cart 28.02 22 36 32.2 20 29.6 24 LSG PFI System in a Roadcase 23.25 39.5 28.75 34.5 www.ultratecfx.com 6
Краткое содержание страницы № 7
Operating Procedure 1. The fog machine must be connected to a grounded supply of at least 15 amps free of any interference. 2. Open a 20 Litre (5 Gallon) container of Ultratec Special Effects fog fluid and insert the fluid pickup tube into the spout of the fluid container. 3. Connect the Remote Handset into the rear panel connector located on the rear panel. (When using DMX the Remote is not required). 4. Activate the Power switch located on the rear panel. The Power switch and Handset indicat
Краткое содержание страницы № 8
Operation Procedure LSG MK II High Pressure w/ 20 & 50lbs Cylinders The Operation Procedures outlined in this section, refer to Figure A and Figure B on Page 9 and 10. 1. Place the fog machine’s output nozzle firmly against the center of the foam ring, sealing it to the input port of the LSG MK II. Tech Tip: Proper alignment can be observed by shining a flashlight into the 10” exit port of the LSG MK II and noting the fogger’s output nozzle is centered on the LSG MK II input port. 2. Connect
Краткое содержание страницы № 9
9. Verify cool temperature output by using your hand and passing it through the fog-CO2 output noting the temperature. 10. After use, turn off the valves and trigger the LSG MK II to depressurize the system before attempting to disconnect hoses. Note that the valves and lines may be extremely cold during operation. Prevent handling and flexing of lines when chilled. Figure A Liquid Carbon Dioxide LSG Control Signal Fog Fluid High Pressure Bottles without Siphon Tubes inverted to obtain li
Краткое содержание страницы № 10
Figure B Liquid Carbon Dioxide LSG Control Signal Fog Fluid Liquid Siphon Tube Liquid Carbon Dioxide High Pressure Bottles w/ Liquid Siphon Tube Installation Model Shown Above Touring Model Available www.ultratecfx.com 10
Краткое содержание страницы № 11
Operation Procedure LSG MK II Low Pressure w/ 350lbs Dewar Tank The Operation Procedures outlined in this section, refer to Figure C on Page 12. 1. Place the fog machine’s output nozzle firmly against the center of the foam ring sealing it to the input port of the LSG MK II. Tech Tip: Proper alignment can be observed by shining a flashlight into the 10” exit port of the LSG MK II and noting the fogger’s output nozzle is centered on the LSG MK II input port. 2. Connect the blue Twist lock conn
Краткое содержание страницы № 12
10. Verify cool temperature output by using your hand and passing it through the fog-CO2 output noting the temperature. 11. After use, turn off the valves and trigger the LSG MK II to depressurize the system before attempting to disconnect the hoses. Note that the valves and lines may be extremely cold during operation. Prevent handling and flexing of lines when chilled. Figure C Liquid Carbon Dioxide LSG Control Signal Fog Fluid 350lb Liquid Carbon Dioxide Dewar 20 Litre Fluid in a box I
Краткое содержание страницы № 13
Options Remotes - The Show Control Remote and Timer/ Duration Remote are compatible with the Power Fog Industrial, Power Fog Industrial w/ Air Option, Power Fog Industrial 9D and Power Fog Industrial 9D w/ Air Option. Each remote is sold separately. Jug Holder - The Power Fog Industrial 9D and Power Fog Industrial 9D w/ Air Option has been designed to be versatile in any setting. For ease of operation, a jug holder may be used to secure the fluid to the machine. The Jug Holder is sold separa
Краткое содержание страницы № 14
Closed “Dry” Contact Show Control Operation Show Control Show control is achieved by connecting a “Dry” or zero voltage contact to the show control terminals. The Power Fog Industrial requires no power to signal the fog, only one set of contacts that close for the entire fogging cue. For Show Control Operation, the DMX Address must be set on 555. Closing the Show Control Remote terminals with dry contacts, triggers the following machine functions: C + 1 = On/ Off w/ Variflow C + 2 = LSG On
Краткое содержание страницы № 15
DMX Operation The Power Fog Industrial is equipped with DMX controls as a standard feature. 1. Attach a DMX signal to the DMX IN 5 pin connector on the rear of the unit. A terminator may be required on the DMX OUT connector in some applications. 2. Select a valid DMX address on the thumbwheel selector for the base address of the fogger. If an air option is present 3 consecutive address will be required. Base DMX= fog rate controlled 0-100%, DMX+1=LSG power on above 50%, and DMX+2= air on abo
Краткое содержание страницы № 16
Warranty Warranty: All warranty is for one year parts and labour unless specified or manufacturer defect only. Abuse or Poor Maintenance will not be covered under warranty. Ultratec Special Effects Fluids must always be used. Use of any non Ultratec Special Effects Fluids will void all warranties. Accept no substitutions as there are no exceptions to this rule. Proof of Purchase or Proof of Sale must always accompany any warranty returns. An RA (return authorization) number must be noted on
