Краткое содержание страницы № 1
OPERATOR’S MANUAL
3/8 in. 12 VOLT DRILL
2-SPEED
R820011
Your drill has been engineered and manufactured to our high standards for dependability, ease of operation, and operator
safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Thank you for buying a RIDGID product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
1
Краткое содержание страницы № 2
TABLE OF CONTENTS Introduction ........................................................................................................................................................................2 General Safety Rules ..................................................................................................................................................... 3-4 Specific Safety Rules ................................................................................................
Краткое содержание страницы № 3
GENERAL SAFETY RULES Do not overreach. Keep proper footing and balance WARNING! at all times. Proper footing and balance enable better control of the tool in unexpected situations. READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may Use safety equipment. Always wear eye protection. result in electric shock, fire and/or serious personal Dust mask, non-skid safety shoes, hard hat, or hearing injury. protection must be used for appropriate conditions
Краткое содержание страницы № 4
GENERAL SAFETY RULES When servicing a tool, use only identical replacement SERVICE parts. Follow instructions in the Maintenance section Tool service must be performed only by qualified of this manual. Use of unauthorized parts or failure to repair personnel. Service or maintenance performed by follow Maintenance Instructions may create a risk of unqualified personnel may result in a risk of injury. shock or injury. SPECIFIC SAFETY RULES Never use a battery that has been dropped or
Краткое содержание страницы № 5
SAFETY RULES FOR CHARGER tain chemicals that can damage, weaken, or destroy WARNING! plastic. READ AND UNDERSTAND ALL INSTRUCTIONS. An extension cord should not be used unless Failure to follow all instructions listed below, may absolutely necessary. Use of improper extension result in electric shock, fire and/or serious personal cord could result in a risk of fire and electric shock. If injury. extension cord must be used, make sure: a. That pins on plug of extension cord are the
Краткое содержание страницы № 6
SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta- tion of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power min Minutes Time Alternating Current Type of current Direct Current Type or a characteristic of current n No Load Speed Rotational speed, at no load o Class II Construction Doub
Краткое содержание страницы № 7
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING Indicates an imminently hazardous situation, which, if not avoided, will DANGER: result in death or serious injury. Indicates a potentially hazardous situation, which, if not avoided, could WARNING: result in death or serious injury. Indicates a potentially hazardous situation, which, if not avoided, may CAUTION: result in minor or moderate injury.
Краткое содержание страницы № 8
FEATURES PRODUCT SPECIFICATIONS Chuck ...........................................................3/8 in. Keyless Clutch ................................................................ 24 Position Motor ..................................................................12 Volt DC Torque ................................................................... 350 in.lb. Switch ..........................................................Variable Speed Charger Input ................................... 120
Краткое содержание страницы № 9
FEATURES KNOW YOUR DRILL KEYLESS CHUCK See Figure 1. The keyless chuck allows you to hand-tighten or release the Before attempting to use this product, familiarize yourself drill bit in the chuck jaws. with all operating features and safety rules. TORQUE ADJUSTMENT RING BIT STORAGE The drill has a 24-position clutch. The torque adjustment Bits provided with the drill can be placed in the storage area, ring can be turned to select the right amount of torque for located on the base of the dr
Краткое содержание страницы № 10
OPERATION WARNING: Do not allow familiarity with your tool to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury. WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of attachments o
Краткое содержание страницы № 11
OPERATION LED FUNCTION OF CHARGER See Figure 3. LED BATTERY RED GREEN ACTION INDICATOR PACK LED LED Power Without battery pack ON OFF Ready to charge battery pack When battery pack reaches cooled Evaluate Hot battery pack Flashing OFF temperature, charger begins fast charge mode When battery pack reaches warmed Evaluate Cold battery pack Flashing OFF temperature, charger begins fast charge mode Charger pre-charges battery until nor- Evaluate Deeply discharged Flashing OFF mal voltage is reac
Краткое содержание страницы № 12
OPERATION TO INSTALL BATTERY PACK See Figure 4. Lock the switch trigger on the drill by placing the direction of rotation selector in center position. Place battery pack in the drill. Align raised rib on battery pack with the groove inside the drill. Make sure the latches on each side of the battery pack snap in place and battery pack is secured in the drill before beginning operation. CAUTION: When placing battery pack in the tool, be sure raised rib on battery pack aligns with
Краткое содержание страницы № 13
OPERATION UNLOCK DIRECTION OF ROTATION SELECTOR (RELEASE) DRILL BIT (FORWARD/REVERSE/CENTER LOCK) CHUCK See Figure 5. BODY The direction of bit rotation is reversible and is controlled by a selector located above the switch trigger. With the drill held in normal operating position, the direction of rotation selector should be positioned to the left of the switch trigger for drilling. The drilling direction is reversed when the selector is to the right of the switch trigger. Setting the s
Краткое содержание страницы № 14
OPERATION TO DECREASE ADJUSTING ADJUSTABLE TORQUE CLUTCH TORQUE RING See Figure 8. This product is equipped with an adjustable torque clutch for driving different types of screws into different ma- terials. The proper setting depends on the type of material and the size of screw you are using. ADJUSTING TORQUE There are twenty-four torque indicator settings located on the front of the drill. Rotate the adjusting ring to the desired setting. • 1 - 4 For driving small screws • 5 - 8 For dri
Краткое содержание страницы № 15
OPERATION REMOVING BITS See Figure 10. Lock the switch trigger by placing the direction of rotation selector in the center position. Open the chuck jaws. NOTE: Rotate the chuck body in the direction of the arrow marked UNLOCK to open the chuck jaws. Do not use a wrench to tighten or loosen the chuck jaws. Remove the drill bit. DRILLING Check the direction of rotation selector for the correct setting (forward or reverse).� Secure the material to be drilled in a vise or with clam
Краткое содержание страницы № 16
MAINTENANCE GENERAL MAINTENANCE WARNING: Avoid using solvents when cleaning plastic parts. Most When servicing use only identical RIDGID plastics are susceptible to damage from various types of replacement parts. Use of any other parts may commercial solvents and may be damaged by their use. Use create a hazard or cause product damage. clean cloths to remove dirt, dust, oil, grease, etc. WARNING: WARNING: Do not at any time let brake fluids, gasoline, Always wear safety goggles or safet
Краткое содержание страницы № 17
MAINTENANCE MALLET CHUCK REMOVAL See Figures 13 - 15. The chuck may be removed and replaced by a new one. CHUCK JAWS Lock the switch trigger by placing the direction of rotation selector in center position. Insert a 5/16 in. or larger hex key into the chuck of the drill and tighten the chuck jaws securely. Tap the hex key sharply with a mallet in a clockwise di- rection. This will loosen the screw in the chuck for easy removal. Open the chuck jaws and remove the hex key. Using a sc
Краткое содержание страницы № 18
NOTES 18
Краткое содержание страницы № 19
WARRANTY ® RIDGID HAND HELD AND STATIONARY POWER TOOL 3 YEAR LIMITED SERVICE WARRANTY Proof of purchase must be presented when requesting war- WHAT IS NOT COVERED ranty service. This warranty applies only to the original purchaser at retail ® and may not be transferred. This warranty only covers de- Limited to RIDGID hand held and stationary power tools fects arising under normal usage and does not cover any purchased 2/1/04 and after. This product is manufactured malfunction, failure or d
Краткое содержание страницы № 20
OPERATOR’S MANUAL 3/8 in. 12 VOLT DRILL 2-SPEED R820011 Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www.ridgid.com. The model number of this tool is found on a plate attached to the motor housing. Please record the serial number in the space provided b
