Краткое содержание страницы № 1
OPERATOR’S MANUAL
1/2 in. DRILL
DOUBLE INSULATED
R7111
Your drill has been engineered and manufactured to our high standard for dependability, ease of operation, and operator
safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Thank you for buying a RIDGID product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
1
Краткое содержание страницы № 2
TABLE OF CONTENTS Introduction ...................................................................................................................................................................... 2 General Safety Rules .....................................................................................................................................................3-4 Specific Safety Rules ..................................................................................................
Краткое содержание страницы № 3
GENERAL SAFETY RULES Remove any adjusting key or wrench before turning WARNING: the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal Read all instructions. Failure to follow all injury. instructions listed below may result in electric shock, fire and/or serious injury. The term “power Do not overreach. Keep proper footing and balance tool” in all of the warnings listed below refers at all times. This enables better control of t
Краткое содержание страницы № 4
GENERAL SAFETY RULES When servicing a power tool, use only identical SERVICE replacement parts. Follow instructions in the Have your power tool serviced by a qualified repair Maintenance section of this manual. Use of person using only identical replacement parts. This will unauthorized parts or failure to follow Maintenance ensure that the safety of the power tool is maintained. instructions may create a risk of shock or injury. WARNING! To reduce the risk of injury, user must read
Краткое содержание страницы № 5
SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power min Minutes Time Alternating Current Type of current Direct Current Type or a characteristic of current n o No Load Speed Rotational speed, at no load Class II Tool Double-insula
Краткое содержание страницы № 6
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING Indicates an imminently hazardous situation, which, if not avoided, will result DANGER: in death or serious injury. Indicates a potentially hazardous situation, which, if not avoided, could result WARNING: in death or serious injury. Indicates a potentially hazardous situation, which, if not avoided, may result in CAUTION minor or moderate injury. (Wi
Краткое содержание страницы № 7
ELECTRICAL DOUBLE INSULATION EXTENSION CORDS Double insulation is a concept in safety in electric power When using a power tool at a considerable distance from tools, which eliminates the need for the usual three-wire a power source, be sure to use an extension cord that has grounded power cord. All exposed metal parts are isolated the capacity to handle the current the tool will draw. An from the internal metal motor components with protect- undersized cord will cause a drop in line voltage
Краткое содержание страницы № 8
FEATURES PRODUCT SPECIFICATIONS Chuck ....................................................................... 1/2 in. Input ............................... 120 V, 60 Hz, AC only, 8.0 Amps Switch ............................. VSR (Variable Speed Reversible) Net Weight ................................................................. 5 lbs. No Load Speed ....................................0-850 r/min. (RPM) CHUCK LOCK-ON BUTTON AUXILIARY HANDLE ASSEMBLY DIRECTION OF ROTATION SELECTOR (FORWARD/RE
Краткое содержание страницы № 9
ASSEMBLY UNPACKING WARNING: This product has been shipped completely assembled. If any parts are damaged or missing do not operate Carefully remove the tool and any accessories from the this tool until the parts are replaced. Failure to box. Make sure that all items listed in the packing list are heed this warning could result in serious personal included. injury. Inspect the tool carefully to make sure no breakage or damage occurred during shipping. Do not discard the packing mat
Краткое содержание страницы № 10
OPERATION FORWARD DIRECTION OF ROTATION SELECTOR (FORWARD/REVERSE) See Figure 3. REVERSE The direction of bit rotation is reversible and is controlled by a selector located above the switch trigger. With the drill held in normal operating position, the direction of rotation selector should be positioned to the left of the switch trigger for forward drilling. The drilling direction is reversed when the selector is to the right of the switch trigger. DIRECTION OF ROTATION CAUTION: SELECTOR
Краткое содержание страницы № 11
OPERATION USING THE AUXILIARY HANDLE ASSEMBLY TO TIGHTEN See Figure 6. Your drill is equipped with an auxiliary handle assembly. For ease of operation, use the handle with either the left or right 360° hand. The handle can be rotated 360°. ROTATION To adjust the auxiliary handle assembly: Loosen the handle assembly by turning the handle coun- terclockwise. Rotate the handle assembly to the desired operating TO position. LOOSEN Securely tighten by turning the handle assembly clock- AU
Краткое содержание страницы № 12
OPERATION DRILLING See Figure 8. Depress and release the switch trigger to be sure the drill is in the OFF position before connecting it to power supply. Check the direction of rotation selector for correct setting (forward or reverse). Secure the material to be drilled in a vise or with clamps to keep it from turning as the drill bit rotates. Plug the drill into power supply source. Hold the drill firmly and place the bit at the point to be drilled. Depress the switch trigger to
Краткое содержание страницы № 13
MAINTENANCE MALLET WARNING: CHUCK JAWS When servicing use only identical RIDGID replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask. GENERAL MAINTENANCE HEX KEY Avoid using solvents when cleaning plastic parts. Most Fig. 9 plastics are susceptible to damage from various types of commercial
Краткое содержание страницы № 14
MAINTENANCE Insert the hex key into the chuck and tighten the chuck TO RETIGHTEN A LOOSE CHUCK jaws securely. Tap the hex key sharply with a mallet in The chuck may become loose on the spindle and develop a clockwise direction. This will tighten the chuck on the a wobble. Also, the chuck screw may become loose, caus- spindle. ing the chuck jaws to bind and prevent them from closing. Open the chuck jaws and remove the hex key. To tighten: Tighten the chuck screw. Unplug the drill. N
Краткое содержание страницы № 15
WARRANTY ® RIDGID HAND HELD AND STATIONARY POWER TOOL 3 YEAR LIMITED SERVICE WARRANTY Proof of purchase must be presented when requesting WHAT IS NOT COVERED warranty service. This warranty applies only to the original purchaser at ® retail and may not be transferred. This warranty only covers Limited to RIDGID hand held and stationary power tools defects arising under normal usage and does not cover any purchased 2/1/04 and after. This product is manufactured malfunction, failure or def
Краткое содержание страницы № 16
OPERATOR’S MANUAL 1/2 in. DRILL DOUBLE INSULATED R7111 Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www.ridgid.com. The model number of this tool is found on a plate attached to the motor housing. Please record the serial number in the space provided bel
