Краткое содержание страницы № 1
Model No. RBBE1996.0
Serial No.
USER’S MANUAL
Write the serial number in the
space above for future reference.
V
Serial Number Decal (Under Seat)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-877-994-4999
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
www.reebokservice.com
CAUTION
Visit our website at
Read all precautio
Краткое содержание страницы № 2
TABLE OF CONTENTS IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PART IDENTIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 ASSEMBLY . . . . . .
Краткое содержание страницы № 3
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precautions before using the inversion table. 1. Read all instructions in this manual before the short knob is fully tightened before you using the inversion table. Use the inversion use the inversion table. table only as described in this manual. 13. Perform all activities on the inversion table in 2. It is the responsibility of the owner to ensure a slow, controlled manner. Aggressive exer- that
Краткое содержание страницы № 4
BEFORE YOU BEGIN ® Thank you for selecting the versatile REEBOK model number is RBBE1996.0. The serial number can INVERSION SYSTEM inversion table. The inversion be found on a decal attached to the inversion table table will increase your intervertebral dimension, (see the front cover of this manual). decrease pressure on intervertebral discs, stretch and relax your muscles, and temporarily relieve back pain To avoid a registration fee for any service needed associated with the listed conditions
Краткое содержание страницы № 5
PART IDENTIFICATION CHART See the drawings below to identify small parts used in assembly. The number in parentheses by each drawing is the key number of the part, from the PART LIST on page 18. Note: Some small parts may have been pre- assembled. If a part is not in the parts bag, check to see if it has been preassembled. M4 x 30mm Screw (63) M6 Washer (62) M10 x 16mm Button Screw (54) M10 x 35mm Button Bolt (53) M4 x 15mm Screw (58) M10 Washer (68) M10 x 53mm Button Bolt (78) M8 x 16mm Button
Краткое содержание страницы № 6
ASSEMBLY • Tighten all parts as you assemble them, unless Make Assembly Easier instructed to do otherwise. This manual is designed to ensure that the • As you assemble the inversion table, make sure inversion table can be assembled successfully that all parts are oriented as shown in the by almost anyone. However, the inversion table drawings. has many parts, and the assembly process will take time. Most people find that if they set aside • For help identifying small parts, use the PART plenty
Краткое содержание страницы № 7
2. Attach the Left Base (1) to the Right Base (2) 2 with two M10 x 80mm Button Bolts (52), four 2 M10 Curved Washers (79), and two M10 79 65 Nylon Locknuts (65). 42 Attach another Foot (42) to the Right Base (2) 71 with an M4 x 20mm Screw (71). 1 79 52 3. Attach the Support Leg (13) to the Center 3 Base (3) with three M10 x 35mm Button Bolts (53) and three M10 Nylon Locknuts (65). 14 Attach the Base Plate (14) to the Center Base (3) with four M5 x 25mm Screws (59). 13 53 53 3 59 65 59 4. Attach
Краткое содержание страницы № 8
5. Attach the Center Base (3) to the Left and 5 52 Right Bases (1, 2) with four M10 x 80mm 79 Button Bolts (52), four M10 Curved Washers (79), and four M10 Nylon Locknuts (65). 79 2 1 52 79 52 79 3 65 6. See the inset drawing. Identify the Center 6 32 65 Frame (7). 64 70 48 Apply some of the included grease to both sides of the Left Large Spacer (31). 5 31 7 Attach the Left Large Spacer (31) and the Left Frame (4) to the Center Frame (7) with an M10 Nylon Locknut (65), an M10 Large Grease Washe
Краткое содержание страницы № 9
8. Attach the Top Cover (23) and the Bottom 8 23 Cover (24) to the Center Frame (7) with two 58 24 M4 x 15mm Screws (58) and an M4 x 30mm Screw (63). 63 7 Attach the Center Frame Extension (6) to the Center Frame (7) with two M10 x 53mm 58 Button Bolts (78) and two M10 Nylon Locknuts 78 (65). 6 65 9. Orient the Headrest Frame (9) and the 9 Backrest Frame (8) as shown. Attach the Headrest Frame to the Backrest Frame with two M10 x 16mm Button Screws (54). 9 54 54 8 10. Apply a small amount of gr
Краткое содержание страницы № 10
11. See the left inset drawing. Identify the Top 11 Largest holes Tube (16), the Bottom Tube (17), and the must be on top Ankle Brace Tube (18); the Tubes have differ- ent lengths and holes in different positions. 16 17 18 16 Orient the Top Tube (16) and the Bottom Tube (17) so that the largest holes are on top 17 (see the right inset drawing), and insert them into the indicated holes in the Leg Frame (10). Attach each Tube with an M4 x 10 15mm Screw (58). 18 Orient the Ankle Brace Tube (18) as
Краткое содержание страницы № 11
14. Identify the two Rear Ankle Braces (80), which 14 have holes in the indicated locations. Slide a Rear Ankle Brace (80) onto the Ankle Brace Tube (18). Attach the Rear Ankle Brace 80 with two M4 x 15mm Screws (58). Make sure that the Screws are tightened into the indi- cated holes in the Ankle Brace Tube. Next, 80 press a 19mm Round Cap (45) into the Ankle Brace Tube, and attach the Round Cap with 45 an M4 x 15mm Screw (58). 58 18 Holes Attach the other Rear Ankle Brace (80) to Holes 58 the
Краткое содержание страницы № 12
17. Attach the Headrest (20) to the Headrest 17 Frame (9) with two M6 x 18mm Button Screws 9 20 (55), an M6 x 55mm Button Screw (56), and 62 three M6 Washers (62). 56 Attach the Backrest (21) to the Backrest Frame (8) in the same way. 55 62 21 8 18. Attach a Handle (12) to the Left Frame (4) with 18 two M10 x 80mm Button Bolts (52), two M10 12 Curved Washers (79), and two M10 Nylon Locknuts (65). Attach the other Handle (12) in the same way. 12 65 Make sure that all parts are properly tight- e
Краткое содержание страницы № 13
ADJUSTMENT This section explains how to adjust the inversion table. See DEVELOPING A PROGRAM on page 16 for impor- tant information about how to get the most benefit from the inversion table. Make sure that all parts are properly tightened each time you use the inversion table. Replace any worn parts immediately. The inversion table can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents to clean the inversion table. SELECTING THE BACKREST FRAME POSITION 8 Hole
Краткое содержание страницы № 14
USING THE ANKLE LOCK To secure your ankles in the inversion table, pull the Lock Handle (33) out as far as it will go, and Notches move the Lock Frame (11) away from the Leg 33 Frame (10). Stand on the Foot Plate (19), with the backs of your legs against the Rear Ankle Braces 11 10 (80). Then, push the Lock Frame against your ankles and engage the Lock Handle into a notch in the Leg Frame. 80 19 WARNING: Always make sure that the Lock Frame (11) is secured snugly against your ankles before using
Краткое содержание страницы № 15
ROTATING ON THE INVERSION TABLE This section explains how to rotate back on the inversion table, and then return to the starting position. Before using the inversion table, see the ADJUSTMENT section starting on page 13 to correctly set up the inversion table. It may be helpful to have a second person ready to assist you as you learn to use the inversion table. ROTATING BACK ON THE INVERSION TABLE ROTATING UP ON THE INVERSION TABLE To rotate back on the inversion table, slowly lift your To retu
Краткое содержание страницы № 16
DEVELOPING A PROGRAM This section contains information and suggestions about using the inversion table. Make sure that all parts are properly tightened each time you use the inversion table. Replace any worn parts immediately. See the ADJUST- MENT section starting on page 13 to identify parts referred to in this section. BENEFITING FROM USING THE INVERSION TABLE INTERMEDIATE PROGRAM If you feel nauseated while using the inversion table, The following are suggestions for persons who have return t
Краткое содержание страницы № 17
NOTES 17
Краткое содержание страницы № 18
PART LIST—Model No. RBBE1996.0 R0107A Key No. Qty. Description Key No. Qty. Description 1 1 Left Base 43 1 Long Adjustment Knob 2 1 Right Base 44 2 32mm Round Cap 3 1 Center Base 45 4 19mm Round Cap 4 1 Left Frame 46 2 16mm Spacer 5 1 Right Frame 47 2 Pivot Bushing 6 1 Center Frame Extension 48 2 29mm Spacer 7 1 Center Frame 49 1 Bumper 8 1 Backrest Frame 50 1 Lock Pin 9 1 Headrest Frame 51 4 M10 x 85mm Button Bolt 10 1 Leg Frame 52 10 M10 x 80mm Button Bolt 11 1 Lock Frame 53 3 M10 x 35mm Butto
Краткое содержание страницы № 19
EXPLODED DRAWING—Model No. RBBE1996.0 R0107A 39 69 33 20 34 58 35 80 58 58 62 56 10 9 55 45 36 18 62 54 67 58 72 58 21 61 58 37 58 80 54 58 58 11 45 19 62 22 56 58 45 58 72 17 65 61 68 58 16 22 45 58 46 55 68 65 57 12 62 8 60 44 65 73 70 32 58 23 38 7 75 24 49 74 65 47 63 12 58 44 79 48 43 65 64 5 47 65 32 31 52 78 65 65 77 65 76 30 32 65 65 64 6 29 48 28 27 39 66 79 52 76 2 26 42 4 62 42 71 79 71 52 25 65 51 65 65 15 65 40 3 41 79 79 14 65 52 65 59 1 58 58 42 13 50 71 65 53 52 51 59 79 52 79 40
Краткое содержание страницы № 20
ORDERING REPLACEMENT PARTS To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to pro- vide the following information: • the MODEL NUMBER of the product (RBBE1996.0) • the NAME of the product (REEBOK INVERSION SYSTEM inversion table) • the SERIAL NUMBER of the product (see the front cover of this manual) • the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and the EXPLODED DRAWING on pages 18 and 19) LIMITED WARRANTY ICON Health
