Руководство по эксплуатации Porter-Cable D22722-028-3

Краткое содержание страницы № 1

ESPAÑOL: PÁGINA 9
Instruction manual
FRANÇAIS: PAGE 17
Manual de
Instrucciones
1/2" Reversible Drill
Manuel d'instructions Taladro Reversible
de 1/2"
Perceuse réversible de
1/2 po
MODEL
PTD501
MODELO
PTD501
MODÈLE PTD501
To learn more about Porter-Cable visit
our website at:
http://www.porter-cable.com
IMPORTANT
Para obtener más información sobre
Please make certain that the person who is
Porter-Cable, visite nuestro sitio web en:
to use this equipment carefully reads and
http://www.porte

Краткое содержание страницы № 2

SAFETY GUIDELINES - DEFINITIONS This manual contains indicates an imminently hazardous situation which, if not information that is avoided, will result in death or serious injury. important for you to know and indicates a potentially hazardous situation which, if not understand. This information re- avoided, could result in death or serious injury. lates to protecting YOUR SAFE- TY and PREVENTING indicates a potentially hazardous situation which, if not EQUIPMENT PROBLEMS. To avoided,may resu

Краткое содержание страницы № 3

HAZARD RISK OF LOSS OF HEARING WHAT COULD HAPPEN HOW TO PREVENT IT  Long term exposure to noise produced from the opera-  Always wear ANSI S3.19 hearing protection. tion of air tools can lead to permanent hearing loss. HAZARD RISK TO BREATHING INHALATION HAZARD WHAT COULD HAPPEN HOW TO PREVENT IT  Abrasive tools, such as grinders, sanders, and cut-off  Always wear MSHA/NIOSH approved, properly fitting tools generate dust and abrasive materials which can face mask or respirator when using suc

Краткое содержание страницы № 4

HAZARD RISK OF INJURY (continued) WHAT COULD HAPPEN HOW TO PREVENT IT  Improperly maintained tools and accessories can cause  Maintain the tool with care. serious injury.  Keep a cutting tool sharp and clean. A properly maintained tool, with sharp cutting edges reduces the risk of binding and is easier to control.  There is a risk of bursting if the tool is damaged.  Check for misalignment or binding of moving parts, breakage of parts, and any other condition that affects the tool’s operati

Краткое содержание страницы № 5

SPECIFICATIONS Free Speed 600 RPM Maximum Working Pressure 90 PSI Air Inlet 1/4" NPT Recommended Hose Size 3/8" I.D. Keyless Chuck 1/2” Air Consumption @ 90 PSI 6.0 SCFM ASSEMBLY Accessories Required IMPORTANT: Line pressure or hose inside diameter should be increased to compensate for unusually long air hoses (over 25 feet). Minimum hose diameter should be 3/8” I.D. and fittings should have 1/4” NPT thread. Assemble Stabilizer Handle 1. Slide stabilizer handle onto tool, rotate to desired pos

Краткое содержание страницы № 6

To use:
Turn air compressor on and allow air tank to fill.
Set the air compressor’s regulator to 90 PSI. This tool operates at a maximum 90 PSI pressure.
This tool has a stabilizer handle (C). Loosen stabilizer handle and rotate to desired position and tighten.
Place the tool in reverse or forward position.
Position drill bit at the point to be drilled and depress the C trigger.
Always disconnect air supply when changing drill bits.
Release trigger to stop tool.
When job is co

Краткое содержание страницы № 7

REPAIR PARTS 38 23 37 18 (5) 33 32A 29 41 32 27 33 42 30 28 26 Ref No. Part No. Description Qty 18 u Rotor Blade 5 23 u Motor Gasket 1 26 + Trigger 1 27 + Spring 1 28 + O-Ring 1 29 + O-Ring 1 30 + Valve Bearing 1 32 + Bushing 1 32a + Valve Shaft 1 33 + O-Ring 2 37 + Spring Pin 1 38 s Hand Grip 1 41 s Handle 1 42 s Handle Ring 1 + Only available in Trigger Repair Kit D25318 u Only available in Tune Up Kit D26762 s Only availabe in Service Kit D25328 NOTE: Parts not listed are not serviceable. 7

Краткое содержание страницы № 8

LIMITED WARRANTY PORTER-CABLE CORPORATION warrants to the original purchaser that all products covered under this warranty are free from defects in material and workmanship. Products covered under this warranty include air compressors, air tools, service parts, pressure washers, and generators, which have the following warranty periods: 3 YEARS - Limited warranty on 2-stage oil-free air compressor pumps that operate at 1725 RPM. 2 YEARS - Limited warranty on oil-lubricated air compressor pumps.