Краткое содержание страницы № 1
Great Plains Mfg., Inc.
Installation Instructions
6 Foot Drill
Seed Box Agitator Option
Used with:
When you see this symbol, the subsequent instructions and
• 605NT
warnings are serious - follow without exception. Your life and
!
! the lives of others depend on it!
• 3P605NT
• 3P600
General Information
These instructions explain how to install the agita-
Before You Start
tor option. The agitator stirs the seed directly
Beginning on page 8 are detailed listings of parts
above the metering cu
Краткое содержание страницы № 2
Great Plains Mfg., Inc. 2 Seed Box Agitator Option See Figure 2: 5. Slide lock collars (8 and 10) against bearing and flanges (7 and 11) and tighten set 2. Slide agitator shaft (5) into seed box from left screws. side of drill. 3. As shaft advances, slide on parts in the fol- lowing order. • 35 tooth sprocket (6) • bearing and flanges (7) • lock collar (8) • bearing and flanges (9) • lock collar (10) • bearing and flanges (11) 4. Attach bearings and flanges to divider (12) and inside of end
Краткое содержание страницы № 3
Great Plains Mfg., Inc. Installation Instructions 3 Drive Assembly 605NT and 3P605NT Drive NOTE: If your drill is equipped with a native grass option, a majority of the agitator drive is already installed. Go to page 4 for chain routing. See Figure 3: 1. Mount bearings and flanges (1) to left side of drill frame and to the frame support as shown. Use 5/16 x 1 inch bolts (2), washers and nuts to secure flanges. Leave bolts loose. 2. Install drive shaft (3) through bearings. As you install sh
Краткое содержание страницы № 4
Great Plains Mfg., Inc. 4 Seed Box Agitator Option 5. Refer to Figure 4. Install 16 tooth splined sprocket (11) to gearbox as shown, and fas- ten with snap ring (12). See Figure 5: 6. Route chains as follows: a. The 45 pitch chain around new 16 tooth sprocket (13) on gearbox to 17 tooth sprocket (14). b. The 89 pitch chain around 17 tooth sprocket (15) near left side of frame to 35 tooth sprocket (16) on agitator shaft. 18728 Figure 4 7. Adjust idlers to remove chain slack. Gearbox Sprocke
Краткое содержание страницы № 5
Great Plains Mfg., Inc. Installation Instructions 5 3P600 Drive 3P600 Drive w/Small Seeds Option See Figure 6: If your drill is equipped with a small seeds option, 1. Mount bearing and flanges (1) inside end a majority of the agitator drive is already installed. panels of drill frame. Use 5/16 x 1 inch bolts Refer to Figure 6: (2), washers and nuts to secure flanges. • Place 17 tooth sprocket (5) near left drill Leave bolts loose. frame end panel. 2. Install drive shaft (3) through bearings.
Краткое содержание страницы № 6
Great Plains Mfg., Inc. 6 Seed Box Agitator Option See Figure 7: 6. Install two 12 tooth idler sprockets (10) in lo- cations shown, using 1/2 x 3 1/2 inch bolts (11), hex jam nuts (12), USS flat washers (13) and hex flange nuts (14). See Figure 8: 7. Route chains as follows: a. The 63 pitch chain around new 12 tooth sprocket (15) on gearbox to 22 tooth sprocket (16). b. The 68 pitch chain around 17 tooth sprocket (17) near left side of frame to 35 tooth sprocket (18) on agitator shaft. 1873
Краткое содержание страницы № 7
Great Plains Mfg., Inc. Installation Instructions 7 5. Start over with paddle 1 and continue until Agitator Paddle Installation each feeder cup has a paddle. The fully as- See Figure 9: sembled shaft will have a spiral result. 1. Place an agitator paddle (1) over the hex shaft 6. After checking for interference, torque the directly above a feeder cup. Position paddle paddle bolts to 9 ft. lbs. (108 in lbs.) as shown (paddle 1). 2. Slip a 1/4 x 2 inch hex flange bolt (2) through the paddle a
Краткое содержание страницы № 8
Great Plains Mfg., Inc. 8 Seed Box Agitator Option 118-748A 3P600 AGITATOR ASSY W/DRIVE - 7-1/2" Your kit includes: Qty. Part No. Part Description 9 118-493D AGITATOR PADDLE 3/4 HEX 2 118-494D LOCK COLLAR 3/4 HEX BORE 1 118-498D SEED FLOAT DOWN FLOAT STOP 1 118-556D 6’ DRILL AGITATOR SHAFT 1 133-037D SGS/AUXILLARY DRIVE SHAFT 1 136-065D CHAIN RL #40 63 PITCHES 1 136-111D CHAIN RL #40 68 PITCHES 2 168-127D 3/16 X 1 KEY 1 800-141C SNAP RING EXT F/PEERLESS G.B. 4 801-035C SCREW SET 5/16-18 SKT KP
Краткое содержание страницы № 9
Great Plains Mfg., Inc. Installation Instructions 9 118-750A 605NT & 3P605NT AGITATOR ASSY W/DRIVE Your kit includes: Qty. Part No. Part Description 9 118-493D AGITATOR PADDLE 3/4 HEX 2 118-494D LOCK COLLAR 3/4 HEX BORE 1 118-498D SEED FLOAT DOWN FLOAT STOP 1 118-556D 6’ DRILL AGITATOR SHAFT 1 202-182D AUXILLARY DRIVE SHAFT 1 136-054D CHAIN RL #40 89 PITCHES 1 136-161D CHAIN RL #40 45 PITCHES 1 168-127D 3/16 X 1 KEY 1 800-141C SNAP RING EXT F/PEERLESS G.B. 4 801-035C SCREW SET 5/16-18 SKT KP
Краткое содержание страницы № 10
Great Plains Mfg., Inc. 10 Seed Box Agitator Option 118-749A 3P600 AGITATOR ASSY WITHOUT DRIVE - 7-1/2" Your kit includes: Qty. Part No. Part Description 9 118-493D AGITATOR PADDLE 3/4 HEX 2 118-494D LOCK COLLAR 3/4 HEX BORE 1 118-498D SEED FLOAT DOWN FLOAT STOP 1 118-556D 6’ DRILL AGITATOR SHAFT 1 136-111D CHAIN RL #40 68 PITCHES 1 168-127D 3/16 X 1 KEY 4 801-035C SCREW SET 5/16-18 SKT KP X 3/8 1 802-039C HHCS 1/2-13X3 GR5 6 802-282C RHSNB 5/16-18X1 GR5 9 802-448C HFSS 1/4-20X2 GR5 6 803-00
Краткое содержание страницы № 11
Great Plains Mfg., Inc. Installation Instructions 11 118-788A 3P600 AGITATOR ASSY W/DRIVE - 6" Your kit includes: Qty. Part No. Part Description 11 118-493D AGITATOR PADDLE 3/4 HEX 2 118-494D LOCK COLLAR 3/4 HEX BORE 1 118-498D SEED FLOAT DOWN FLOAT STOP 1 118-556D 6’ DRILL ADGITATOR SHAFT 1 133-037D SGS/AUXILLARY DRIVE SHAFT 1 136-104D CHAIN RL #40 62 PITCHES 1 136-111D CHAIN RL #40 68 PITCHES 2 168-127D 3/16 X 1 KEY 1 800-141C SNAP RING EXT F/PEERLESS G.B. 4 801-
Краткое содержание страницы № 12
Great Plains Mfg., Inc. 12 Seed Box Agitator Option 118-789A 3P600 AGITATOR ASSY WITHOUT DRIVE - 6" Your kit includes: Qty. Part No. Part Description 11 118-493D AGITATOR PADDLE 3/4 HEX 2 118-494D LOCK COLLAR 3/4 HEX BORE 1 118-498D SEED FLOAT DOWN FLOAT STOP 1 118-556D 6’ DRILL AGITATOR SHAFT 1 136-111D CHAIN RL #40 68 PITCHES 1 168-127D 3/16 X 1 KEY 4 801-035C SCREW SET 5/16-18 SKT KP X 3/8 1 802-039C HHCS 1/2-13X3 GR5 6 802-282C RHSNB 5/16-18X1 GR5 11 802-448C HFSS 1/4-20X2 GR5 6 803-008C
