Краткое содержание страницы № 1
1001 O1 LEG PRESS
WARNING:
Read and follow all directions
for each step to insure proper
assembly of thi,,; product.
ASSEMBLY INSTRUCTIONS
1 Revision: 12/4/00
Part # 7037301
Rev. A
Краткое содержание страницы № 2
]IMPORTANT NOTES] Please note: * Thank you for purchasing the Parabody 100101 LEG PRESS. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. We recommend cleaning your product (pads and flame) on a regular basis, using warm soapy water. Touch-up paint can be purchased flom your Parabody customer service representative at (800) 328-9714. There is a risk assumed by individuals who use t
Краткое содержание страницы № 3
PARTS LIST !KEY PART # DESCRIPTION QTY KEY PART # DESCRIP 3N QT¥ 1 6574508 BASE FRAME 1 18 3102601 3/8" LOCK WASHER 4 2 6573608 SEATFRAME , 1 19 3102802 3/8" LOC) NUT 2 3 6575008 REAR TUBE 1 20 3102807 3/8" LOW HEIGH’ LOCK NUT 1 4 6575408 FOOT PLATE 1 21 3102801 1/2" LOCI{ NUT 2 5 6573908 LEVER TUBE 2 22 3102804 1/2" LOW HEIGHT LOCK NUT 2 6 6476408 HANDLE 1 23 3102941 3/8 X 1-1/2" BOLT 2 7 6575102 ADJUSTMENT TUBE 1 24 3102922 3/8 X 2-3/4" BOLT 2 8 6597421 SEAT PAD 2 25 3102904 3/8 X 3" BOLT 2 9
Краткое содержание страницы № 4
3/8 FIGURE 1 STEP 1: ¯ Attach two 2" SQ. COVER CAPS (15) onto the ends &the REAR TUBE (3) as shown in FIGURE ¯ Insert four 2" SQ. ENDCAPS (13) into the ends of the BASE FRAME (1) as shown in FIGURE SECURELY assemble the REAR TUBE (3) to the BASE FRAME (1) using two 3/8 X 3" BOLTS (25), 278" FLAT WASHE RS (17), and two 3/8" LOCK NUTS (19). See FIGURE ] 1/2 1/2 1/2 [ I/2 [ 1/2 [ I I 1/:! I 0 1 2 3 4 5 6 4
Краткое содержание страницы № 5
I / / FIGURE 2 STEP 2: ¯ Insert two 2" SQ. ENDCAPS (13) into file ends of the SEAT FRAME (2) as shown in FIGURE ¯ SECURELY assemble one 3/8" SPRING PIN (33) to the spring pin barrel on the SEAT FRAME (2) as shown in FIGURE ¯ Attach four PARAGLIDE STRIPS (14) to the inside of the SEAT FRA~£E (2) using file following steps: ¯ Thoroughly clean all surfaces where the PARAGLIDE STRIPS (14) are to be attached. ¯ l~emove the PARAGLIDE STRIPS (14) from the paper backing and firmly apply them to all sh
Краткое содержание страницы № 6
3/8" LOW HEIGHT / FIGURE 3 STEP 3: ¯ SECURELY assemble one 3-1/2" PULLEY (11), two 2" WHEELS (16), two 3/8" FLAT WASHERS (17):. and two 3/8 ID SPACERS (29) to the ADJUSTMENT TUBE (7) using one 3/8 X 4-1/2" BOLT (26) as shown in FIGURE ¯ Attach four PARAGLIDE STRIPS (14) to the outside of the ADJUSTMENT TUBE (7) using the followirtg steps: ¯ Thoroughly clean all surfaces where the PARAGLtDE STRIPS (14) are to be attached. ¯ Remove the PARAGLIDE STRIPS (t4) from the paper backing and firmly appl
Краткое содержание страницы № 7
PIN FIGURE 4 STEP 4: ¯ CAREFULLE¥ slide the ADJUSTMENT TUBE (7) over into the SEAT FRAME (2) and engage the SPRING PIN into one the adjustment holes. See FIGURE 4. STEP 5: ¯ Insert two 3/4" FLANGE BEARINGS into each of the two LEVER TUBES (5) shown in FIGURE 5. FIGURE 5
Краткое содержание страницы № 8
5/16" SET SCREW~ FIGURE 6 STEP 6: ¯ Insert four 2" SQ. END CAPS (13) into the ends of two LEVER TUBES (5) as shown in FIGURE SECURELY assemble the LEVER TUBES (5) to the BASE FRAME (1) using two 3/4" SHAFTS (9) and. SECURE in ¯ using four 5/16" SET SCREWS (32). See FIGURE 1/2 1/2 [ 1/2 I 1/2 I 1/2 I 6 4 2 I I I I I
Краткое содержание страницы № 9
FIGURE 7 STEP 7: ¯ Insert four 2" SQ. END CAPS (13) into the ends of FOOT PLATE (4) as shown in FIGURE ¯ Insert eight 1/2" FLANGE BEARING (30) into the LEVER TUBES (5) as shown in FIGURE
Краткое содержание страницы № 10
1/2" LOW HEIGHT @~’"" FIGURE 8 STEP 8: ¯ SECURELY assemble the FOOT PLATE (4) to the LEVER TUBES (5) using two 1/2 X 6-1/2" BOLTS (28) and two 1/2" HEIGHT LOCK NUTS (22) as shown in FIGURE ¯ CAREFULLY attach eight NON-SKID STRIPS (12) to the FOOT PLATE (4) as shown in FIGURE
Краткое содержание страницы № 11
3-1/4" FIGURE 9 STEP 9: ¯ SECURELY assemble the SEAT FRAME (2) to the LEVER TUBES (5) using two 1/2 X 3-1/4" BOLTS (27) and two 1/2" NUTS (21) as shown in FIGURE 11
Краткое содержание страницы № 12
/ / ! I I I / I / I / I I I I I i I I I I / I / I ~ / I I I I / / / / 1 / 3/8 ~ X 1-1/2"~ FIGURE 10 STEP 10: ¯ SECURELY assemble the SEAT PAD (8) to the HANDLE (6) and the SEAT FRAME (2) using two 3/8 X 1-1/2" BOLTS two 3/8" LOCK WASHERS (18), and two 3/8" FLAT WASHERS (17). See FIGURE 1/2 [ 1/2 112 [ 1/2 [ 6 2 1 I [ I I I I I I 1 ] I 1 12
Краткое содержание страницы № 13
X 2-3/4~/ FIGURE 11 STEP 11: ¯ SECURELY assemble the SEAT PAD (8) to the SEAT FRAME (2) using two 3/8 X 2-3/4" BOLTS (24) and two 3/8" WASHERS (18) as shown in FIGURE 11. ¯ Slide two 1 X 8" GRIPS (10) over each HANDLE (6) as shown in FIGURE 13
Краткое содержание страницы № 14
FIGURE 12 STEP 12: ¯ To adjust the SEAT, sit in the LEG PRESS, gently press against the FOOT PLATE and pull back on the SPRING PiN. ¯ Refer to the LEG PRESS ADAPTOR assembly instructions to attach the 832102 LEG PRESS to the home gym. Thank you for purchasing the Parabody 100101 LEG PRESS. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714. 3;/2 I 1/2 I 1/2 I 1/2 112 1/2 I I I I 6 3 2 1 0 I I I I I I I I I
