Краткое содержание страницы № 1
Serious Steel
950 ST
9501.02 ASSEMBLY INSTRUCTIONS
P, zv~on: 08104197
Part # 6705001
Краткое содержание страницы № 2
! ! ! ATTENTION ! ! ~ UNLE,:,S 0 THER WISE SHOWN, z~LL CONNECTIONS WILL CONSIST OF ONE 1~ ~o~ ~; two ~N~ ONF~ a),,gOC~N~r. BOLT ~ LOCKNUT NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE ~ .OF THE BOLT. ~/i////i~ BOLT LENGTH BOLT LENGTH RULER: 1/2 ] 1/2 .. I 1/2 1/2 I 3 4 5 6
Краткое содержание страницы № 3
950 ST Parts List KEY PART. # DI-’$CRIPTION ~QTY. KEY P~RT # DESCRiPTi ,N Q1 6623603 PF~ESS’ WT STACK BASE WHT 1 62 64’12001 IASSY S’PRING PiN 318 D/ , 2 6624202 ;BACK PAD ANGLE LEFT BLK 1 63 641660’ GLIDE1-1/2 X 3/4 UHMV~ PE QTY8 ’’2 3 6624302 BACK PAD ANGLE’ RIGHT BLK 1 64 6466’90" ASSY SPRING PiN 1/2 DI, 2 4 6622903 PEC ~,RM RIGHT WHT 1 65 310380’ LINK SNAP 5/16 4 5 6623003 PEC AR~ LEFT W~T 1 66 31049~i BEWARING FLG 3/4 ID X 10D 6 6 6623503 PRESS ARM WHT 1 67 6214501 WEIGHT PLATE 7 6624502 CA
Краткое содержание страницы № 4
Frame Assembly Instructions Use th~s procedure to assemble the frame of the ParaBady 950ST ~ .~t/8" X 4’ NUT X 3" I~rtLT ~ Step I Loosely assembler the leg we|~ht base (18) and the press weight stack base (1~, to 1’he base A. (15) using two 1/2 x 5-1/2 bolts (91), four 1/2" washers(79), and two 1/2’ nyl¢)ck nuts shown. Apply two non-sk~d strips (61~ to the base as shown. Loo~ly assemble the fro.nf upright ~31) to ~he base (15) using two 1/2 3- 1/2: bolts ~9 1), fo ur 1/2’ washers (79~, and ~wo
Краткое содержание страницы № 5
Step 2 ’ Securely assemble the f!,oatln~ p.ulle.y stop (3.2~, and the s.eaf, support (33). to the front ~,prlght (31) A. using two 1/2 x 4-,1/2 bolts (.gO), four 1/Z~ washers (~79), and two 1/2" nylock nuts (82). Securely assemble one 3/6" spring pin (62) to the seat support (33) as shown. e. Securely a~tach one seat pad (45) to the pad support (38) ~sing two 3/6 ~ bol ts (cJ T), andtwo. C. 3/8" washers (75) as shown. CarefUlly insert the pa’d support (5I~) into the sect support (33) and ,engage
Краткое содержание страницы № 6
2-314"
Краткое содержание страницы № 7
)3/8 X 3" Step 4 bol~ tw~,.11z" urel attach the press ~ase (13) to the base (15) using ~wo IlZ x.3-~I/4" bolts (!19;~ the rear upright (~21) using one ;~/o A. nylocK nut (B3). wasne~ L{=~ ,~"= "7- "~o~ ~.~ --e 3/B (95), tWO 5/B washers L~o) ....... Securely assemble one 3/B" spring pin (62) to ~he wolff sleeve (39) as shown. Affach one u-pin 1’,115) ~o the wolff sleeve (39) using one 1/2" pal nu] (6B). Slide c,ne ca.p (58) on~o ~he u-pin as shown. Carefully slide ass~mbled wolff sleeve (39) on
Краткое содержание страницы № 8
Step 5 /2. x 3" bolt; (~,7), two 3/8 Securely attach the press frame (17) to the pr.e.ss base (13) us;ng one nylock nu~ 1,82), and two A. 3" bolts (95), "~wo 1/2" washers C79), fo.u.r 3/8, washers (78), one nylock nu~s (B3). (Note: Make sure 3/8 bolts are facing down.) 9
Краткое содержание страницы № 9
Step 6 SlTde two hinge tabs (73) onto the wolff sleeve (39) and securely attach press seat pl:ld (49) A. two 3/8 x 1" bolf;~ (97), and two 3/8" washers (78). (Note: The "hinge" part of the hinge should face upward.) Slide the right back pad angle (2) and left back pad angle (5) onto the wolff sleeve (39) ’B. attach the press back pad (50) using four 3/8 x 1" bolts (97), and four 3/B" wash=:rs Secure the 1/2 x 2 x 15-1/2" plate (116) to right back pad angle (2) and the left back pad angle C. u
Краткое содержание страницы № 10
318 X LOV HEIGHT NUT HEIGHT NUT Step 7 Loosely attach the press arm odiu.sj (25) tp the rear up~!ght (21) using two 1" pillow block A. bearings (112), four 3/8 x 3-1/4: bolts ~9B), four 5/B washers ~TB~, and four 5/8" nylock nuts ~No~e: A~och pillow blocks ~112~ so the set screws ore on ~he inside, this w~ll ollow mote adjustment. Center press arm adjust ~ZS~ ~o I~ne up wHh the post on ~he press bose ~13~ and securely tighten B. se~ screws on the pillow block bearings ~112~. Adjust pillow block
Краткое содержание страницы № 11
31/B ° X 3-1/4 (~1/2 X 3-114" ~ ,~~ Step 8 Securely attach the re(=r leg base (10) and ihe leg curl handle (9) to the leg frame (14) using A. 1/2 x 3- " bolts (.B9), two 3/8 x 3-1/4". ,,bolts (98), four 1/2" washers (79), four " washers (7B), two 11//~" nylock nuts (82), and two 3/B nylock Securely attach the right I351 & left (40)leg extension handles (35).to the I.g frame (I’) using two 3/8 x 3--1/4" bolts 98, four 3/8" washers (78), and two 3/8 nylock nuts Securely assemble one 1/2" spring
Краткое содержание страницы № 12
STEP 9-B ~ STEP 9-A STEP g Slide two hinge tabs; (73) onto the leg frame (14) and securely attach leg scat pad (4T) using A. 3/8 x I" bolls (97), and two 5/B" washers (TB). (Nole: The "hinge" part of the hinge tab should face downward.) B. Atiach $wo roller p.a, ds (19) to the leg frame (14) u(s;;~ one 16-3/~".roller pad shaft ,’,27), as shown plastic washers (55,1 and two 3/4" starlock, collars 318 X SEE NOTE 3/B x %" ]~TTN frame (14) using STEP 10 Attach leg back pad ad|ust (11), and leg bac
Краткое содержание страницы № 13
STEP 11. Securely assemble two 3/8" spring pins (62) to the leg curl/extension (8) as shown. A. Apply eight 1-1/2 x 5/A-" glides (63) to the outside surfaces of each roller pad adiuster (34) B. shown, and insert roller pad adjusters (34) into the leg curl/extenslon (8). (Note: Tl~e, end " will need to be temporarily removed.) C. Securely assemble leg frame (14) to the leg weight stack base (18) using two 1/2 x 5-.1/4" bolts (Bg), four 1/Z" washers (79), and two 1/Z" nylock nuts (B2). D. Attach
Краткое содержание страницы № 14
I Step 12 Insert two plate bushings ~102~ |nto She °’ParaBody" side of each of sixty weight plates (677 as A. shown. B. Insert one guide rod (28~ through one weight stock cushion (109~ and into each of the large hales in the base C15), the leg welghf stock base ~IB~, and the press weight stack press (1~ as shown. Ccrefully slide twen~ weight plates C67) onto eachset of guide rods (28~ with the "Pcr,=Body" C. side up and the cer=ter key-hole facing outward, Securely assemble one selector shaft (1
Краткое содержание страницы № 15
3Z8 x 3"(~ Step 13 (43..~ onto the pec welght.stack guide rods and Ioosely,,att,,ch it Slide pec guide roC[ support , bolts (95), four 5/8 washers (78), and two 3/8 nyiock using two to the boom nuts (83). (Note: This connection will be secured in a later step after the pulleys are assembled.) Slide press guide rod support (24) and leg guide rod support (25) over their respecfiw~ guide B. rods and securely assemble fl~em fo the boom using two 1/2 x 3-1/2" bolts (91), foIJr 1/2" washers (79), and
Краткое содержание страницы № 16
GUIDE CABLE PART NUMBER STAMPED 65356 PEC DEC% CABLE -77 51B" PART NUMBER STAMPED 66274- PRESS /--- STAMPED PART NUMBER . AB CRUN% ¯ CABLE ./6707B ,, ~,/ --60 3/4"- STAMPED PART NUMBER 66276 " ’ // --~73 7/B’- STAMPED PART NUMBER 67047 -171"-- 17
Краткое содержание страницы № 17
Pec Dec Cable Assembly Instructions Use this procedure to assemble the pec dec cables of the ParaBody 950ST Step C Step F & H Step G I 1318 x ~-3/4." 0 Step D __ E Step 1 In this order, route tthe threaded end of the let cable (107) through the top boom (20), the A. (15), and the large hole in the pec guTde rod support B. Screw the threaded end of the laf cable (107) approx|mately 3/4" into the end of the selector shaft C113) and fighfen, jam nut securely as shown. C, Securely assemble three 3_
Краткое содержание страницы № 18
Step 2 of the pec dec cable (104) |o the slotted bushing on |h~ ri.ght p.ec ~ ^~ the ~ec dec cable around the front upright {,31.~ anc~ A. Connect o.ne..end .... 29. Route the o~l~er e.u .y, . .~% ..... ;o ~e slotted bush, ng on tne ,e’T P== ..... " WO 4--1/2" pulleys (110) to the center B. ~,~-~racket (36) using.~,~o ~/~ ~ ~ ~;;C " f~O’~e" The pec dec co.me snou~o.~= ,=~=’~= . P~"~ --~=x -~ +wo 3/B nylocK nu~s Loo}. _.~,- =~-_ ,,, ~ckets should be pos~ton~.o washers L~o/ ~,,~ .~ ,_L" -~ %he ’L
Краткое содержание страницы № 19
I I I I I I I / / / step Securely assemble ~!he threaded end of the ab crunch cable (105) approximately 3/4" into the end A. the pulley bracket (25) and tighten jam nut securely. B. Securely ass_e,,rnble ’the pec dec c.a.b,,le ~104) a.nd one 5-1/2 pu},ley (11) to the pulley bracket (25) one 3/e x z bolt (tOO), two 3/8 washe~ (78), and one 3/8 ny~ock n,,t (83). (No~’e: Loop cable around ~he pulley prior 9o inserting it into the ’U’ bracket.) 2O
Краткое содержание страницы № 20
I I 4 Step Securely assemble the ball end of the ab .crunch cable (106).a,,nd one 3-1/2" pu. lley (’.111).t~,,,the A. front upright (51) using tw.o 3/6 x 2-3/4: bolts (gg), two 3/8’ flange spacers (74), washers (78), and two 3/8 nylock nuts (83). (Note: The ab crunch cable should be routed underneath the retaining bolt as shown.) the ab crunch cable. I,106) o.d o..e ,+-I12 pu,ey,,(;;O.) ! the f~oc,ting pu~ey Securely as_se._mble.,. ,._,+ r+nn’~ two 3]8 washers ~78), and one 3],.8 ,nymcK nut (83
