Руководство по эксплуатации ParaBody 888101

Краткое содержание страницы № 1

888101 SNI][TH NIACH][NE
ASSEMBLY ]INSTRUCTIONS
Part # 6801501
1 Revision.: 2/10/99

Краткое содержание страницы № 2

WELCOME TO THE WORLD OF ~,~i~u$ ~. ~ee~ Please note: * Thar~k you for purchasing the Parabody 888101 SMITEI MACHINE. Please read these in- structions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your Parabody customer service representative at (800) 328-9714. There is a risk as

Краткое содержание страницы № 3

PART ~,artT # iizsc~ r~o~ 1’" 6798103 12 6692601 3 x 2- END CAP ’2 679~103 LOWER CROSS BRACE 13 3102"910 "a/2 X3 eC,~r 3 67985O2 14 3102502 6’ 4 6798402 15 3102~01 12 ~ 679~702 SMrrl-IBk~ " 16 3105302 7/16"HO1 ;]?LUG 8 6 6798901 2 3105303 9/16"HO1 EPLUG 16 7 6799601 .2 18 6824601 3 - 1/~ X 1-3/ GL/DE 6 , "8 ,. 6799203 2 19 6695801 2 I/2" OD RUBI !RBUMPER 9 6799801 POD 2 "20 3109302 zk I ’10 6714901 GLm)EROD BUSH]NO 4 21 6807101 11 32030o2[ 1" SHAFF COLLAR FIGURE 1 STEP 1: ¯ Insert two 1-3/4" ROU

Краткое содержание страницы № 4

1/2X3"~ FIGURE 2 STEP 2: ¯ LOOSELY assemblethe PLATEHOLDEP--S (7) andtheLOWERCROSS SUPPORT (2) totheUPRIGIff-f FRAMES (8) as FIGURE 2 using four 1/2 X 3" BOLTS (13), and four 1/2" LOCKNUTS (15), LOOSELYassembletheUPPERCROSSSUPPORT(1) tothetopsetofholesoftheupRIGHTFRAMES(8)assh°wninFIGURE2nsing ¯ two 1/2 X3" BOLTS (13), two 1/2" WASHERS (14), andtwo/2" LOCKNUTS (15). ¯ LOOSELY assemble the GUN RACKS (21) to the outside of the UPRIGHT FRAMES (8) as sho~inFIGURE 2 using six 1/2 X 3" BOLTS (13), fo

Краткое содержание страницы № 5

I I I FIGURE 3 STEP 3: ¯ Insert two 3 X 2" END CAP S (12) into the ends of the UPRIGHT FRAMES (8) as shown in FIGURE ¯ Insert four GUIDE ROD BUSHINGS (10) into the UPRIGHT FRAMES (8) as shown in FIGURE 5

Краткое содержание страницы № 6

FIGURE 4 STEP 4: ¯ Insert one 1-3/4" ROUND END CAP (20) into the end of each HOUSING (6) as shown in FIGURE ¯ Slide one 2-1/2" OD BUMPER (19) over the end of each HOUSING (6) as shown in FIGURE ¯ Insert the shaft of the HOUSINGS (6) into the ends of the SMITH BAR (5) as shown in FIGURE I 1/2 I 1/2 I 1/2 I 1/2 I 1/2 0 1 2 3 4 6

Краткое содержание страницы № 7

FIGURE 5 ;TEP 5: ¯ Hookthe SMITH BAR (5) intothe slots ofthe UPRIGHT FRAM]ES (8). ¯ CAREFULLY slide one GUIDE ROD (9) fltrough the upper hole in the UPRIGHT FRAME (8). Slicte one 1" SHAFT COLLAR (1 l) the bottom of the GUIDE ROD (9), the CAREFULLY lower the GUIDE ROD (9) through the HOUSING (6) oft the SMITH t3AR (5) into the bottom hole of the UPRIGHT FRAME (8). Repeat this step on the other side. ¯ Slide the 1" SHAFT COLLARS (11) up the GUIDE RODS (9) to thebushing and SECURELY TIGttTEN. 7

Краткое содержание страницы № 8

FIGURE 6 STEP 6: Attach six 3-1/4 X 1-3/4" OLI]3ES (18) to the LEFT & RIGHT SAFETY STOPS (3 & 4) as shown in FIGURE 6 using following steps: ¯ Thoroughly clean all surfaces where the 3-1/4 X 1-3/4" GLIDES (18) are to be attached. ¯ Remove the 3-1/4 X 1-3/4" GLIDES (18) fromthe paper backing and firmly apply them to all shown surfaces. 1/2 [ 1/2 [ 1/2 [ 1/2 [ 1/2 ] 1/2 [ 1 2 3 4 5 6 8

Краткое содержание страницы № 9

FIGURE 7 STEP 7: ¯ .Assemble the LEFT & RIGHT SAFETY STOPS (3 & 4) to the UPRIGHT FRAMES (8) as shownin FIGURE

Краткое содержание страницы № 10

FIGURE 8 STEP 8: ¯ Insert sixteen 9/16" CAP PLUGS (17) into the exposed holes inthe UPRIGHT FRAMES (8) as shownin FIGURE ¯ Insert eight 7/16" CAP PLUGS (16) into the exposed holes in the UPPER & LOWER CROSS BRACES (1 & 2) as sho~t in FIGURE Thank you for purchasing the Parabody 888101 SMITH MACHINE. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714. 10

Краткое содержание страницы № 11

FIGURE 8 STEP 8: ¯ Insert sixteen 9/16" CAP PLUGS (17) into the exposed holes inthe UPRIGHT FRAMES (8) as shownin FIGURE ¯ Insert eight 7/16" CAP PLUGS (16) into the exposed holes in the UPPER & LOWER CROSS BRACES (1 & 2" as sho~a~ in FIGURE Thank you for purchasing the Parabody 888101 SMffH MACHINE. If unsure ofpropeJ" use of equipment, ca!l Yo_ur loc.a 1 _Pa~abody_~.i~.tributor or call the Parabody customer service department at (800) 328-9714. 10