Руководство по эксплуатации ParaBody 893101

Краткое содержание страницы № 1

Краткое содержание страницы № 2

Краткое содержание страницы № 3

89310! PROSYSTEM ASSEMBLY INSTRUCTIONS Attach one (I) I-1/4 SQ. RUBBER BUMPER to the CENTER of the CARRIAGE STOP on the WEIGHT CARRIAGE. Slide WEIGHT CARRIAGE down over the REAR UPRIGHT of the MAIN UPRIGHT. (NOTE: MAKE SURE THAT THE WEIGHT PEG ON THE WEIGHT CARRIAGE IS FACING TOWARDS THE FRONT OF THE MACHINE) LOOSELY attach the two (2) PULLEY MOUNT FLATS to the REAR and FRONT UPRIGHTS of the MAIN UPRIGHT. using two (2) 3/8 X 3 IN. BOLTS, two (2) 3/8 IN. LOCI(. WASHERS, and two (2) IN. NUTS. (NO

Краткое содержание страницы № 4

-.1 ~---. 0 ~0 ~ o ~0 ~Z ~ = r-i

Краткое содержание страницы № 5

Краткое содержание страницы № 6

0 0 0 0 0 0 0 q~0 0 0 0__0~0. 0 ;. . 000000;~00000

Краткое содержание страницы № 7

x 0 z c~ c -0 0 z z r- 0 c ~ 0 "r 4~Z ~

Краткое содержание страницы № 8

Do not mark this box! Document: 11000258

Краткое содержание страницы № 9

893102 PROSYSTEM. PRODUCT ASSEMBLY INSTRUCTIONS SHEETS 1 12/06/95

Краткое содержание страницы № 10

893102 PROSYSTEM ASSEMBLY PARTS LIST SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSEMBLY HARDWARE: ITEM NAME/DESCRIPTION QTY 1 1/2 X 3-1/2 IN. BOLT ........................................................................................................ 6 i/2 X 3-1/4 IN. BOLT ........................................................................................................ 2. 3 1/2 X 3 IN. BOLT ..................................................................................................

Краткое содержание страницы № 11

893102 PROSYSTEM ASSEMBLY PARTS LIST SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSF_,I~IBLY WELDMENTS/PARTS: ITEM NAME/DESCRIPTION QTY UPRIGHT FRAME W’ELDJ}IENT .................................................................................... 1 2. TOP BO03"I WELD~IENT ................................................................................................ 1 3. CARRIAGE I, VELDMENT ................................................................................................ 1 4. 2 S

Краткое содержание страницы № 12

893102 PROSYSTEM ASSEMBLY INSTRUCTIONS Assemble the appropriate END CAY~S to the UPRIGHT FRAME WELDMENT..BENT TUBE. and the LOW ROWATTACHMENT WELDMENT as shown, also attach the 5-1/2 X 2-1/2 IN. NON SKID STRIPS to the LOWROWATTACHMENT as shown. SECURELY assemble the LOW ROWATTACHMENT WELDMENT and the UPRIGHT FRAME ~VELDJ~IENT to the BENT TUBE as shown. LOOSELY assemble the UPRIGHT WELDMENTS to the BENT TUBE as shown. Attach eight (8) 1 IN. SQ. GLIDES to the CARRIAGE WELDMENT as shown in (DETAIL

Краткое содержание страницы № 13

893102 PROSYSTEM ASSEMBLY INSTRUCTIONS LOOSELY assemble the LEFT and RIGHT BOOM SUPPORT WELDMENTS to the TOP BOOM WELDMENT as shown. LOOSELY assemble the UPRIGHT WELDMENTS to the LEFT and RIGHT BOOM ’3UPPORT WELDMENTS as shown. SECURELY TIGHTEN ALL LOOSE BOLT CONNECTION MADE TO THIS POINT. Assemble the 4 X 7 IN. ROLLER PADS with MUSHROOM CAPS to the SWIVEL KNEE SUPPORT WELDMENT as shown, also assemble one (1) SPRING PIN ASSEMBLY to the SWIVEL KNEE SUPPORT WELDMENT as shown in (DETAIL D) then SEC

Краткое содержание страницы № 14

893102 PROSYSTEM ASSEMBLY INSTRUCTIONS 17. LOW PULLEY CABLE ROUTING ASSEMBL Y (SEE CABLE ROUTING DIAGRA3~I)." ho Route CABLE (657620 i) under and around the PULLEYS at the bottom of the UPRIGHT FRAy’vIE WELDMENT. (NOTE: AFTER CABLE HAS BEEN ROUTED UNDER PULLEY, POSITION CABLE RETAINING CLIP UNDER THE PULLEY AS SHOWN AND TIGHTEN) Route CABLE up and around the bottom PULLEY of the 1-3/4 X 5-1/4 IN. PLATES as shown. and down to, and around the PULLEY under the PULLEY BRACKET WELDMENT. (SEE NOTE ABO

Краткое содержание страницы № 15

u[] co m e (- 0 Fq Z 3> c -0 O0 v c FT~ 0

Краткое содержание страницы № 16

\1 Z

Краткое содержание страницы № 17

x r-~ I :;:u x z zz

Краткое содержание страницы № 18

m o o,4 0 ~ / z // / I \ ,J / \ ’J / \ / / / \\ / / / / Z I / \ / / / / /