Краткое содержание страницы № 1
Northstar 2 kW Radar Installation Manual 1
Краткое содержание страницы № 2
FCC Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a normal installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guaran
Краткое содержание страницы № 3
Warranty The Northstar Warranty Statement is supplied as a separate document. It is shipped with the Product Registration Card. In case of any queries, refer to www.northstarnav.com. Feedback from you Your feedback is important and helps Northstar ensure that this manual is a valuable resource for all marine technicians. E-mail your comments or suggestions about this manual to the following address: manuals@northstarnav.com. Northstar 2 kW Radar Installation Manual 3
Краткое содержание страницы № 4
Contents FCC Statement....................................................................................................................................................................................... 2 Industry Canada.................................................................................................................................................................................... 2 Compliance Statement.....................................................................
Краткое содержание страницы № 5
6.2 Configure the navigator communications......................................................................................................................39 6.3 Heading sensor requirements.............................................................................................................................................39 6.3.1 Disable the heading sensor input .........................................................................................................................
Краткое содержание страницы № 6
1 Preface This manual explains how to install the scanner and the radar processor. It also explains how to set up the radar system after installation and gives information on troubleshooting. This manual is supplementary to Revision C and Revision D of the Northstar 6100i Networked Navigation System Installation Manual Part Number GM6KIM. If the radar will be used with a Northstar 8000i system, this manual should be used with the Northstar 8000i System installation documentation for your
Краткое содержание страницы № 7
Only qualified personnel should install or service this equipment. Installation or servicing work that is done by non-qualified personnel can result in equipment breakdown, poor performance of the equipment, fire, electrical and physical hazards, injury or death. Wear safety equipment such as a hard hat and a safety belt at all times when installing or working on the scanner. The scanner is usually installed in an elevated position and serious injury or death can result if a person fall
Краткое содержание страницы № 8
2 Introduction to the Northstar radar The Northstar radars are designed as an option available to the Northstar 6000i, 6100i, or 8000i systems. A variety of scanner models are available (2 kW, 4 kW, 6 kW, 10 kW and 25 kW) to suit different customer requirements. Each scanner model has a corresponding radar processor model. 2.1 2 kW radar system overview The 2 kW radar system is intended for use in a marine environment. It consists of a dome connected to the 2 kW radar processor by a p
Краткое содержание страницы № 9
2.2 Check the 2 kW radar parts The RDR1021MD 2 kW radar system consists of a scanner, a radar processor, and associated cables. There are two basic options for the 2 kW radar: NS004790R is the standard 2 kW radar system, consisting of a box containing the scanner and the 49 ft (15 m) interconnection cable (NS003100). This is pre-installed into the scanner. NS004790M is the alternative 2 kW radar system, consisting of a box containing only the scanner. This radar system is designed for u
Краткое содержание страницы № 10
NS004790M 2 kW scanner standard components Quantity Item Part name Part no. 1 Scanner unit NS004790 4 Hexagonal bolt Part of Hardware 5/16-18 kit HR000066 UNCx31.75 mm 4 M8 Spring Part of Hardware washer kit HR000066 4 M8 Plain washer Part of Hardware kit HR000066 4 Rubber washer Part of Hardware kit HR000066 1 Packing list LA000450A 1 Installation sheet LA000410A MTZ303386 1 Mounting LA000451A template NS004780R 2 kW radar processor standard components Qua
Краткое содержание страницы № 11
1 Product CD000085A Registration Card 1 Warranty CD000260A 1 Spare 3 A fuse HR000063 4 Mounting screw HR000061 NS003101 Optional longer length interconnection cable for radar scanner - order separately Quantity Item Part name Part No 1 Interconnection NS003101 length cable for the 65.5 ft (20 m) radar scanner NS00481X cable for 8000i installation only - order separately Quantity Item Part name Part no. 1 Network cable NS004810 length for 8000i 1.6 ft (0.5 m) install
Краткое содержание страницы № 12
NS003108 Optional extension cable for 6000i and 6100i installations only - order separately Quantity Item Part name Part no. 1 Radar NS003108 communications extension cable for 6000i and 6100i installation ONLY. 12 Northstar 2 kW Radar Installation Manual
Краткое содержание страницы № 13
3 Install the radar A radar unit should only be installed by a qualified marine technician, as potentially lethal high voltage is present along with heavy rotating parts. There is a transmit interlock that prevents radar transmissions if the scanner is not rotating. However, a high voltage remains for a period of time after the system is turned off. If you are not familiar with this type of electronics, consult with a trained service or installation technician before attempting to service
Краткое содержание страницы № 14
DON'T DO THIS! DON'T install the scanner too high up, where its weight will alter the stability of the vessel and cause degradation of the radar picture over short ranges (see "How to find the optimum height for the scanner"). DON'T install the scanner close to lamps or exhaust outlets. The heat emissions may cause the equipment to breakdown and soot and smoke will degrade the performance of the radar. DON'T install the scanner close to the antennas of other equipment such as directi
Краткое содержание страницы № 15
However, when the power boat is traveling at high speed, the bow rises up out of the water and if the elevation angle (trim) of the bow is raised up so that it equals, or exceeds, 50% of the vertical beam width of the radar, this can cause two problems: ahead of the power boat, the beam is projected too high to sweep the water surface effectively. Targets can be missed completely or appear at a very poor resolution on the display screen. astern of the power boat, the beam is projected
Краткое содержание страницы № 16
3.2 How to find the optimum height for the scanner The optimum height for the scanner is as close as possible to the A-B line for best performance. How to find the A-B Line: The vertical extent of the radar beam is 2 θ°, so most of the radar beam is concentrated within this angle, meaning that outside of this angle the radar beam will be very weak. Scanner model θ° value (half the -3 dB beam width) 2 kW 15 4 kW 12.5 6 kW 10 10 kW 10 25 kW 10 An example of an A-B Line is shown
Краткое содержание страницы № 17
D is distance traveled by the radar beam h1 is the height above sea level of the scanner h2 is the height above sea level of a target An example is shown below: In this example, the scanner is installed on the vessel at a height of 10 ft (3 m) above sea level (h1). Island A is 33 ft (10 m) high (h2) and for comparison, Island B is 16.4 ft (5 m) high (h2). Both islands are at a distance (D) of 10 nautical miles from the vessel. Calculations using the formula show that, at this d
Краткое содержание страницы № 18
3.5 2 kW scanner dimensions Before starting the installation, use the drilling template to identify the: cable inlet drill holes front and rear of the radome location of the drain hole (ensure that your chosen location allows the drain hole to empty). The 2 kW scanner dimensions are shown: 3.6 Install a scanner on a trestle Depending on your chosen location for the scanner, it may be easier to install the scanner if you fabricate a trestle (or radar mast) on which you
Краткое содержание страницы № 19
Orient the trestle so that the cable inlet on the scanner will face the stern, and so that the scanner can be mounted at the correct angle (as discussed in the "Power boat installation" section). Make sure that the edges of the trestle won't trap water. 3.7 Install the 2 kW scanner unit IMPORTANT: Remember that you must screw the bolts into place from the underside of the location site, because the shape of the dome prevents you from installing the bolts from the topside. Ensure that
Краткое содержание страницы № 20
3.8 Install the radar processor Install the radar processor in a dry location away from spray, rain, drips, and condensation. The location site must allow you to easily connect the radar processor to the ship's ground, the interconnection cable, the power cable, and the 6000i and 6100i radar communications cable or the 8000i network cable. Check that these cables and the ship's ground can easily reach the radar processor BEFORE you drill. The radar processor dimensions are shown on the
