Руководство по эксплуатации MTD E602E

Руководство по эксплуатации для устройства MTD E602E

Устройство: MTD E602E
Категория: Снегоочиститель
Производитель: MTD
Размер: 5.86 MB
Добавлено: 9/21/2014
Количество страниц: 28
Печатать инструкцию

Скачать

Как пользоваться?

Наша цель - обеспечить Вам самый быстрый доступ к руководству по эксплуатации устройства MTD E602E. Пользуясь просмотром онлайн Вы можете быстро просмотреть содержание и перейти на страницу, на которой найдете решение своей проблемы с MTD E602E.

Для Вашего удобства

Если просмотр руководства MTD E602E непосредственно на этой странице для Вас неудобен, Вы можете воспользоваться двумя возможными решениями:

  • Полноэкранный просмотр -, Чтобы удобно просматривать инструкцию (без скачивания на компьютер) Вы можете использовать режим полноэкранного просмотра. Чтобы запустить просмотр инструкции MTD E602E на полном экране, используйте кнопку Полный экран.
  • Скачивание на компьютер - Вы можете также скачать инструкцию MTD E602E на свой компьютер и сохранить ее в своем архиве. Если ты все же не хотите занимать место на своем устройстве, Вы всегда можете скачать ее из ManualsBase.
MTD E602E Руководство по эксплуатации - Online PDF
Advertisement
« Page 1 of 28 »
Advertisement
Печатная версия

Многие предпочитают читать документы не на экране, а в печатной версии. Опция распечатки инструкции также предусмотрена и Вы можете воспользоваться ею нажав на ссылку, находящуюся выше - Печатать инструкцию. Вам не обязательно печатать всю инструкцию MTD E602E а только некоторые страницы. Берегите бумагу.

Резюме

Ниже Вы найдете заявки которые находятся на очередных страницах инструкции для MTD E602E. Если Вы хотите быстро просмотреть содержимое страниц, которые находятся на очередных страницах инструкции, Вы воспользоваться ими.

Краткое содержание
Краткое содержание страницы № 1

OPERATOR’S MANUAL
Model Numbers
E642E, E662H,
614E, E644E,
E664F
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
Warning:
covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the oper

Краткое содержание страницы № 2

SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR SNOW THROWER. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. WHEN YOU SEE THIS SYMBOL-HEED ITS WARNING. : WARNING The Engine Exhaust from this product contains chemica

Краткое содержание страницы № 3

• If the snow thrower should start to vibrate • Never operate the machine at high transport abnormally, stop the engine and check speeds on slippery surfaces. Look behind and use immediately for the cause. Vibration is generally a care when backing. warning of trouble. • Never direct discharge at bystanders or allow • Stop engine whenever you leave the operating anyone in front of unit. position, before unclogging the collector/impeller • Disengage power to collector/impeller when housi

Краткое содержание страницы № 4

SECTION 2: FINDING YOUR MODEL NUMBER This Operator’s Manual is an important part of your new snow thrower. It will help you assemble, prepare and maintain your snow thrower. Please read and understand what it says. Before you start to prepare your snow thrower for its first use, please locate the model plate and copy the information from it in this Operator’s Manual. The information on the model plate is very important if you need help from your dealer or the MTD customer support de

Краткое содержание страницы № 5

SECTION 4: CONTENTS OF HARDWARE PACK Lay out the hardware according to the illustration for identification purposes. Parts are illustrated approximately one-half size. Part numbers are shown in parentheses. (Hardware pack may contain extra items which are not used on your unit.) ATTACHING THE HANDLE ASSEMBLY ATTACHING THE CHUTE ASSEMBLY A B Hex Bolts Hex Bolts 1/4-20 x 3/4" Long 5/16-18 x 1-3/4" Long (710-3015) (710-3180) Hex Bolts Hex Lock Nuts 5/16-18 x 3/4" Long 1/4-20 Threa

Краткое содержание страницы № 6

SECTION 5: ASSEMBLY INSTRUCTIONS IMPORTANT: After assembly, service engine Attaching the Handle Assembly. with gasoline, and check oil level as instructed in the (Hardware A and E) separate engine manual packed with your unit. Lay loose parts out on flat surface. Control NOTE: All references to right or left side of the 1. Handle Panel 5. Traction Drive Grip snow thrower are determined from behind the unit 2. Right Handle in the operating position. 6. Right Gri

Краткое содержание страницы № 7

3. Insert curved end of the Z fitting into the top 5. Secure with hex bolt, spacer and lock nut. See hole in the triangular metal tab on the auger Figure 6. (Do not overtighten this bolt as it will control grip. See Figure 5. prevent the grips from automatically returning to their upright position.) 6. Repeat process for the right side Traction Drive Control Grip. Triangle Metal Tab 7. Lay handle assembly behind snow thrower. See Figure 7. Auger Control Grip Hex Bolt (5/16-18 x

Краткое содержание страницы № 8

Traction Shift Drive Lever Clutch Ferrule Flat Washer Hairpin Shift Clip Rod Flat Washer Hairpin Shift Clip Arm Assembly Figure 9 Figure 11 Flat Washer Lock Washers Shift Hairpin Lever Clip Cable Roller Hex Bolt Handle Guide Ferrule 3/4” Long Tab Shift Hex Rod Bolt 1-3/4” Long Flat Washer Figure 10 Hairpin Shift Clip Arm ATTACHING SHIFT ROD Assembly (Hardware D) 1. Place the shift lever in the fifth (5) or the fastest Figure 12 forward speed position. 3. Models 642, 662

Краткое содержание страницы № 9

ATTACHING CLUTCH CABLES 1. Thread the hex jam nuts all the way up the Chute Assembly threaded portion of the “Z” ends. 2. Make certain all cables are in the grooves of the Hex Bolt cable roller guides. The roller guides are located in the lower rear of the unit. Lift the clutch grip in the raised (up) position. 3. Thread the cable onto the threaded portion of the “Z” end until there is no slack in the cable, but the cable is NOT tight. Do not overtighten cable. See Figure 13. Hex

Краткое содержание страницы № 10

4. Place one flat washer on the end of the chute FINAL ADJUSTMENTS crank, then insert the end of the crank into the hole in the plastic bushing in the chute crank Auger Drive Clutch bracket. See Figure 17. 1. To check the adjustment of the auger drive clutch, push forward on the left hand clutch grip Flat Washer Chute Crank depressing the rubber bumper under the clutch grip (See part #13 on page 22). There should be slack in the cable. 2. Release the clutch grip. The cable should

Краткое содержание страницы № 11

Adjusting The Skid Shoes The space between the shave plate and the ground can be adjusted by adjusting the skid shoes. 1. Place skid shoes in the low position to remove snow close to the ground. Place skid shoes in a higher position to remove snow from uneven ground. See Figure 19. Low Position 2. Adjust skid shoes by loosening the four hex High Position nuts and carriage bolts and moving skid shoes Hex Nuts Skid to desired position. Make certain the entire Carriage

Краткое содержание страницы № 12

Auger Auger Traction Drive Drive Drive Traction Clutch Clutch Clutch Drive Clutch Shift Shift Chute Lever Lever Chute Crank Crank Figure 22 Figure 23 SECTION 7: OPERATION BEFORE STARTING WARNING: Observe all Warning Metal Loop Labels on the snow thrower prior to on Spark use. See Figure 1. Plug Wire Rubber Boot Your snow thrower is shipped with oil; however, you must check the oil level before operating. Figure 24 Be careful not to overfill. 3. Make certain the auger and drive clutch lev

Краткое содержание страницы № 13

Follow all instructions carefully. Determine that your 4. Push primer button two or three times. Refer to house wiring is a three wire grounded system. Ask a Figure 21 on page 11. If engine is warm, push licensed electrician if you are not certain. If your primer button once only. house wiring system is not a three-wire grounded NOTE: Always cover vent hole in primer button system, do not use this electric starter under any when pushing. Additional priming may be necessary conditions. If your sy

Краткое содержание страницы № 14

TO ENGAGE DRIVE/AUGER WARNING: Temperature of muffler and 1. With the engine running near top speed, move o surrounding areas may exceed 150 F. shift lever into one of the FORWARD or Avoid these areas. REVERSE positions. Select a speed appropriate for the snow conditions that exist. Use the slower speeds until you are familiar • For most efficient snow removal, remove with the operation of the snow thrower. snow immediately after it falls. 2. Squeeze the left hand auger drive clutch to •Discharg

Краткое содержание страницы № 15

Model 614, 644, 664: 5. If adjustment is necessary, loosen the jam nut on the traction drive cable, and thread cable in 3. Push down on the shift arm assembly as far as or out as necessary. it will go. Thread the ferrule up or down the shift rod and align it with the hole closest to the shift 6. Tighten the jam nut to secure the cable when knob on the narrow side of the shift lever correct adjustment is reached. Reassemble the assembly behind the handle panel. frame cover with six self-tapping

Краткое содержание страницы № 16

SECTION 9: LUBRICATION WARNING: Disconnect the spark GEAR CASE plug wire and ground against the The gear case is lubricated with grease at the engine before performing any factory and does not require checking. If lubrication or maintenance. disassembled for any reason, lubricate with 2 ounces of Shell Alvania grease EPR00, part number ENGINE 737-0168. Before reassembling, remove old sealant Refer to engine manual for all engine lubrication and apply “Loctite 5699” or equivalent. instructions.

Краткое содержание страницы № 17

5. Roll the front and rear auger belts off the engine AUGER BELTS pulley. See Figure 30. NOTE: It is necessary to remove both belts in 6. Unhook the idler spring from the hex bolt on the order to change either one. If changing just one belt, auger housing. See Figure 31. be certain to check the condition of the other belt. 7. Back out the stop bolt to allow the belts to slip 1. Remove the plastic belt cover on the front of the between the bolt and auger pulley. engine by removing the two self-t

Краткое содержание страницы № 18

6. Lightly tap the hex nut to dislodge the ball Friction bearing from the right side of frame. Remove Wheel the hex nut and bell washer from left end of Friction Wheel Disc shaft. 7. Slide the gear shaft to the right and slide the Drive Belt friction wheel assembly from the shaft. 8. Remove the six screws from the friction wheel assembly (three from each side). Remove the Support Bracket friction wheel rubber from between the friction wheel plate. 9. Reassemble new friction wheel rubber to the

Краткое содержание страницы № 19

SECTION 12: TROUBLE SHOOTING GUIDE Trouble Possible Cause(s) Corrective Action Engine fails to start Fuel tank empty, or stale fuel. Fill tank with clean, fresh gasoline. Fuel will not last over thirty days unless a fuel stabilizer is used. Blocked fuel line. Clean fuel line. Choke not in ON position Move switch to ON position Faulty spark plug. Clean, adjust gap or replace. Key not in switch on engine. Insert key. Spark plug wire Connect spark plug wire. disconnected. Primer button not depres

Краткое содержание страницы № 20

SECTION 13: ILLUSTRATED PARTS HOUSING ASSEMBLY 20


Скачавание инструкции
# Руководство по эксплуатации Категория Скачать
1 MTD 150 Руководство по эксплуатации Снегоочиститель 94
2 MTD 190-469A Руководство по эксплуатации Снегоочиститель 6
3 MTD 190-032-101 Руководство по эксплуатации Снегоочиститель 23
4 MTD 179cc Руководство по эксплуатации Снегоочиститель 21
5 MTD 200 Руководство по эксплуатации Снегоочиститель 12
6 MTD 199-658 Руководство по эксплуатации Снегоочиститель 1
7 MTD 191-768 Руководство по эксплуатации Снегоочиститель 1
8 MTD 235 Руководство по эксплуатации Снегоочиститель 2
9 MTD 190-768 Руководство по эксплуатации Снегоочиститель 0
10 MTD 208cc Руководство по эксплуатации Снегоочиститель 57
11 MTD 230, S230, 240, S240, 250, S250, 260, S260, 261, S261 Руководство по эксплуатации Снегоочиститель 5
12 MTD 230 Руководство по эксплуатации Снегоочиститель 0
13 MTD 240 Руководство по эксплуатации Снегоочиститель 16
14 MTD 250 Руководство по эксплуатации Снегоочиститель 8
15 MTD 285 Руководство по эксплуатации Снегоочиститель 0
16 Agri-Fab 45-0402 Руководство по эксплуатации Снегоочиститель 2
17 Agri-Fab 45-0418 ATV Руководство по эксплуатации Снегоочиститель 1
18 Agri-Fab 45-0418 Руководство по эксплуатации Снегоочиститель 1
19 Alliance Laundry Systems DRYING TUMBLERS 70269501R3 Руководство по эксплуатации Снегоочиститель 2
20 Ariens 924 SNO-THRO 924109 Руководство по эксплуатации Снегоочиститель 60