Краткое содержание страницы № 1
IM847-D
March, 2010
LF- 72 WIRE FEEDER
For use with machines having Code Numbers: 11075, 11076, 11077
11209, 11210, 11211, 11227
11290, 11291, 11292, 11293
11606, 11607, 11608, 11609
11708, 11709, 11710, 11711
Safety Depends on You
Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However,
your overall safety can be
increased by proper installation ...
and thoughtful operation on your
part. DO NOT INSTALL, OPER-
ATE OR REPAIR THIS EQUIP-
MENT WITHOUT READING
TH
Краткое содержание страницы № 2
i i SAFETY WARNING CALIFORNIA PROPOSITION 65 WARNINGS Diesel engine exhaust and some of its constituents The engine exhaust from this product contains are known to the State of California to cause can- chemicals known to the State of California to cause cer, birth defects, and other reproductive harm. cancer, birth defects, or other reproductive harm. The Above For Diesel Engines The Above For Gasoline Engines ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY
Краткое содержание страницы № 3
ii ii SAFETY ELECTRIC SHOCK can ARC RAYS can burn. 4.a. Use a shield with the proper filter and cover kill. plates to protect your eyes from sparks and 3.a. The electrode and work (or ground) circuits the rays of the arc when welding or observing are electrically “hot” when the welder is on. open arc welding. Headshield and filter lens Do not touch these “hot” parts with your bare should conform to ANSI Z87. I standards. skin or wet clothing. Wear dry, hole-free gloves to insulate hands. 4.b. Us
Краткое содержание страницы № 4
iii iii SAFETY WELDING and CUTTING CYLINDER may explode SPARKS can if damaged. cause fire or explosion. 7.a. Use only compressed gas cylinders 6.a. Remove fire hazards from the welding area. containing the correct shielding gas for the If this is not possible, cover them to prevent process used and properly operating the welding sparks from starting a fire. regulators designed for the gas and Remember that welding sparks and hot pressure used. All hoses, fittings, etc. should be suitable for mat
Краткое содержание страницы № 5
iv iv SAFETY 5. Toujours porter des lunettes de sécurité dans la zone de PRÉCAUTIONS DE SÛRETÉ soudage. Utiliser des lunettes avec écrans lateraux dans les zones où l’on pique le laitier. Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce 6. Eloigner les matériaux inflammables ou les recouvrir afin de manuel aussi bien que les précautions de sûreté générales suiv- prévenir tout risque d’incendie dû aux étincelles
Краткое содержание страницы № 6
v v TABLE OF CONTENTS for selecting a QUALITY product by Lincoln Electric. We want you to take pride in operating this Lincoln Electric Company product T Th ha an nk k Y Yo ou u ••• as much pride as we have in bringing this product to you! CUSTOMER ASSISTANCE POLICY The business of The Lincoln Electric Company is manufacturing and selling high quality welding equipment, consumables, and cutting equip- ment. Our challenge is to meet the needs of our customers and to exceed their expectations. On
Краткое содержание страницы № 7
vi vi TABLE OF CONTENTS Page Installation ............................................................................................................Section A Technical Specifications ...............................................................................................A-1 Safety Precautions........................................................................................................A-2 Location .................................................................................
Краткое содержание страницы № 8
vii vii TABLE OF CONTENTS Page Maintenance ....................................................................................................Section D Safety Precautions ................................................................................................D-1 Routine Maintenance.............................................................................................D-1 Periodic Maintenance............................................................................................
Краткое содержание страницы № 9
A-1 A-1 INSTALLATION : LF-72 Wire Feeder TECHNICAL SPECIFICATIONS SPEC.# TYPE WIRE FEED SPEED RANGE Wire Size LF-72 Speed Solid Cored K2327-1 Base Model K2327-4 K2327-2 Bench Model 50-800 IPM .023 - 1/16 in. .035 - 5/64 in K2327-5 Standard Duty (1.27-20.3 m/m) (0.6 - 1.6 mm) (0.9 - 2.0 mm) K2327-3 K2327-6 Bench Model K2327-7 Heavy Duty CONTROL BOX, WIRE DRIVE AND COMPLETE UNITS SPEC.# TYPE INPUT POWER PHYSICAL SIZE• TEMPERATURE RATING Input Voltage Dimensions and Curren
Краткое содержание страницы № 10
A-2 A-2 INSTALLATION MOUNTING SAFETY PRECAUTION ELECTRIC SHOCK can kill. For location and size, LF-72 Bench Model Rear • Only qualified personnel should Mounting Holes (See Figure A.1) and for Bottom perform this installation. Mounting Holes (See Figure A.2). • Turn off the input power to the power source at the disconnect switch or fuse box before working on this equipment. Turn off the input power to any other equipment FIGURE A.1 connected to the welding system at the disconnect switch
Краткое содержание страницы № 11
A-3 A-3 INSTALLATION BENCH MOUNT BOOM MOUNT When boom mounting, remove the wire reel stand (if The LF-72 mounts in a variety of configurations. As assembled) and secure the wire feeder directly to the shipped from the factory, the LF-72 is suitable for desired surface. bench mounting or placing directly on top of the weld- ing power source (CV-xxx and DC-xxx product family only). Bench Mount SUSPENDED SWIVEL MOUNT Only suspend the wire feeder by the lift bail of the portability kit. Both th
Краткое содержание страницы № 12
A-4 A-4 INSTALLATION SAFETY PRECAUTION ELECTRIC SHOCK can kill. • Only qualified personnel should perform this installation. • Turn off the input power to the power source at the disconnect switch or fuse box before work- ing on this equipment. Turn off the input power to any other equipment connected to the weld- ing system at the disconnect switch or fuse box before working on this equipment. • Do not touch electrically hot parts. --------------------------------------------------------
Краткое содержание страницы № 13
A-5 A-5 INSTALLATION COAXIAL WELD CABLES A coaxial weld cable is constructed by 8 small leads wrapped around one large lead. The large inner lead Coaxial welding cables are specially designed welding connects to the electrode stud on the power source cables for pulse welding or STT welding. Coaxial weld and the electrode connection on the wire feeder. The cables feature low inductance, allowing fast changes small leads combine together to form the work lead, in the weld current. Regular cable
Краткое содержание страницы № 14
A-6 A-6 INSTALLATION ANALOG CONTROL CABLE CONTROL CABLE CONNECTIONS • All control cables can be connected end to end to extend their length. The control cable connecting the wire feeder to the power source is specially made for the welding envi- ronment. The wire feeder power requires overcurrent protec- tion. Connect the wire feeder only to power sources with overcurrent protection of no more than 15 amps. POWER SOURCE WIRE FEEDER A J J A K K I B I B N H N L C L C H G M M G D D E F E F P
Краткое содержание страницы № 15
A-7 A-7 INSTALLATION ANALOG MILLER CONTROL CABLE ADAPTER K2335-1 This Lincoln Electric wire feeder may be mounted to a limit- ed number of Miller Electric power sources. The Miller power source must have the amphenol pin definition shown in the table below for proper operation of the wire feeder. Operation of Lincoln wire feeders on Miller power sources may result in lack of high speeds or reduce pull force on high wire feed speeds. Maximum wire feed speed for the LF-72 operating on a Miller
Краткое содержание страницы № 16
A-8 A-8 INSTALLATION WELDING GUN/WIRE FEEDER TRIGGER REMOTE SENSE LEAD SPECIFICATIONS CONNECTOR Refer to the power source instruction manual for Wire Feeder Amphenol instructions for connecting the wire feeder for STT welding. E Welding Gun A D WIRE DRIVE SYSTEMS B C Trigger Lead Drive Roll Kits are designed to feed specific types and wire sizes. The LF-72 Bench Model comes with the combo KP1696-1. All other Drive Roll Kits listed are not included, but are available for ordering from the Wire
Краткое содержание страницы № 17
A-9 A-9 INSTALLATION WELDING GUNS, TORCHES AND ACCES- 3. Fully insert the gun cable connector end into the SORIES gun receiver bushing and gently tighten the thumb screw as show in Figure A.5. GUN RECEIVER BUSHING The LF-72 wire feeder comes with a K1500-2 gun 4. Connect the gun trigger connector to the trigger receiver bushing. receptacle. Make sure that the key ways are aligned and insert. MAGNUM GUN AND CABLE ASSEMBLIES The LF-72 wire feeder model will accept a number of optional gun an
Краткое содержание страницы № 18
A-10 A-10 INSTALLATION PROCEDURE FOR CHANGING WIRE DRIVE CONFIGURATION (See Figure A.5) DRIVE AND IDLE ROLL SETS Changing the Gun Receiver Bushing (See Figure A.4 ) WARNING WARNING ELECTRIC SHOCK can kill. ELECTRIC SHOCK can kill. • Turn the input power OFF at the dis- connect switch or fuse box before • Turn the input power OFF at the attempting to connect or discon- welding power source before instal- nect input power lines, output lation or changing drive rolls and/or cables or control ca
Краткое содержание страницы № 19
A-11 A-11 INSTALLATION 7. Disconnect the shielding gas hose from the gun PRESSURE ARM ADJUSTMENT bushing, if required. WARNING 8. Connect the shielding gas hose to the new gun bushing, if required. ELECTRIC SHOCK can kill. 9. Rotate the gun bushing until the thumb screw hole • Turn the input power OFF at the aligns with the thumb screw hole in the feed plate. welding power source before instal- Slide the gun receiver bushing into the wire drive lation or changing drive rolls and/or and verif
Краткое содержание страницы № 20
A-12 A-12 INSTALLATION WIRE REEL LOADING 3. Re-install the retaining collar. Make sure that the release bar snaps out and that the retaining collar fully engages the groove on the spindle. WARNING FIGURE A.8 • Keep hands, hair, clothing and tools away from rotating equipment. Retaining • Do not wear gloves when threading wire or Collar changing wire spool. • Only qualified personnel should install, use or service this equipment. ----------------------------------------------------------------
