Руководство по эксплуатации Life Fitness 701

Краткое содержание страницы № 1

701
PARABODY 525 PEC DEC OPTION
PRODUCT ASSEMBLY
INSTRUCTIONS SHEETS

Краткое содержание страницы № 2

t t t ATTENTION t ~t .e~,~ ~~ ~F O~NE ~ _ONE (1) L 0 CK .~ NUT, BOLT, WASH~

Краткое содержание страницы № 3

,ux r~t~tl ~z~ fist, IJtst~ AI 1. AbbENIIgL¥ PARTS LIST (/~EVEL 1,) SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSE1VII3LY QTY NAME/DESCRIPTION ITEM 2 I/2 x 4-I/2 IN. BOLT .............................................................................................................. 2 318 X 2 IN. BOLT .................................................................................................................... 2. 2 3/4 IN. WASHER ..............................................................

Краткое содержание страницы № 4

701 FACTOR 525 PEC DEC ATT. ASSEMBLY PARTS LIST (LEVEL 2) SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSE/VIBLY ITEM NAME/DESCRIPTION QTY I. ~/~ x 2 rs. BOLT 3/8 IN. WASHER ................................... g 4. I/4 I~. WASH~-R .............................. 2 .......... 2 ..................................................................... 5. 2 ~z~ r~. LOCK Nut .......................... 22.2222222222222.222222222222222222"222222 ...... 22 ........................ 2 6. ~/8 rs. LOW ~*G~r LOCK

Краткое содержание страницы № 5

COTERLESS HITCH PIN (2)----------_.~ LEFT PEC DEC . 2 SQ. END CAP RIGHT PEC DEC ,~ EY BRACKET 3/4 IN. WASHER LEFT ARM ADVANCE RIGHT ARM ADVANCE~ I PAD (2) --~ "-...4 X .‘ ~ I..2 ROLLER "-.. ~’ /-- CAM STOR CARRIAGE GUIDES (2) -’-~’- ""’~ HO°’-ING -’’’’" BEARING u~ ¯ / l / / ( ) / ’ !.. TAR’ ~oCK COLOR 2 s/~ D S / END C~~ (2) ~2 SQ. d~ P~BODY ~C. ~ ~ AS~ INSL 701101

Краткое содержание страницы № 6

701 FACTOR 525 PEC DEC ATT. ASSEMBLY INSTRUCTIONS (LEVEL 1) NOTE: IF THE SHROUD IS ASSEMBLED TO THE FACI’OR 525, IT WILL NEED TO BE REPdOVED TO ASSEMBLE THE PEG DEC ATTACHMENT. PLEASE REMOVE THE SHROUD AT THIS TIME BY CAREFULLY REMOVING TIIE FOURTEEN (14) SHROUD FASTENEFKg. o Insert two (2) 2 IN. SQ. END CAPS into both ends of the BEARING HOUSING, as shown on drawing. SECURELY assemble the BEARING HOUSING and the CENTER PULLEY BRACKET to the FRONT UPRIGHT as shown on drawing, using p, vo (2) I/’

Краткое содержание страницы № 7

__ FACTOR 525 PEC DEC ATT. ASSEMBLY INSTRUCTIONS (LEVEL 2) LOOSEN the 3/8 X 4 1N. BOLT that ~ssembles the two (2) PULLEYS, and two (2) I/2 IN. SPACERS |o the BASE directly behind the FRONT UPRIGHT. Remove the 3/8 IN. LOCK NUT, and the 3/8 IN. WASHER.. Slide the BOLT out enough to remove the two (2) 1/2 IN. SPACERS. Replace if.it I/2 IN. SPACERS with one (I) .~-I~ X I IN. PULLEY, as shown in (VIEW B-B). Slide BOLT back Replace the 3/8 IN. WASHER., and 3/8 IN. NUT. TIGHTEN CONNECTION SECURELY. S

Краткое содержание страницы № 8

701 FACTOR 525 PEC DEC ATT. ASSEMBLY INSTRUCTIONS (LEVEL 2) The D-lUNG CABLE CLIP on the end of the LINK CABLE shouid restljust above the D-RING. If the LINK CABLE seems to be pulling on the D-RING or is resting too far above the D-RING, adjust it by raising or lowering the two (2) 1/4-2~ IN. NUTS that attaches the LINK CABLE to the PULLEY BRACKET. When the correct height is obtained SECURELY tightea the two (2) 1/4-28 NUTS together around the PULLEY BRACKET. 9. To adjust the pre-streteh on the

Краткое содержание страницы № 9

! FRON’F OF MACHINE I I ! .! ! SEE VIEW C-C D /-_D-R~NG DETAIL A ~S__HR__C,UD (’SEE VIEW j-t.INK CABL[ / ! I x 2 PULL- LINK ~ CA- o ; --~ L-PIN

Краткое содержание страницы № 10

D-RING C VIEW B-B FASTENERS 04) FRONT OF MACHINE MIDDLE UPRIGHT Vl~ F-F DETAIL C-C / VIEW D-D