Краткое содержание страницы № 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
MARCY PREMIER
Hardware Identifier
HOME GYM
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
PREMIER
Retain This
Manual for
Reference
09-23-02
IMPEX FITNESS PRODUCTS
OWNER'S
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
MANUAL Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.
Краткое содержание страницы № 2
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES...................................................................……….. 2 HARDWARE IDENTIFIER.....….....................................................................……….. 3 ASSEMBLY INSTRUCTIONS.........................................................................……….. 4 PARTS LIST…………………………………………………………………………………..16 RESISTA
Краткое содержание страницы № 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one per
Краткое содержание страницы № 4
3
Краткое содержание страницы № 5
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Slide two Round Rubber Bumpers (#55) onto the Guide Rods (#14). Align the holes and push two Guide Rods (#14) into the Rear Stabilizer (#2). Secure each Guide Rod with one M10 x ¾” Allen Bolt (#72) and ∅ ¾” Washer (#81) on the bottom. B.) Inst
Краткое содержание страницы № 6
STEP 2 (See Diagram 2) A.) Attach the Main Base Frame (#1) to the Rear Stabilizer (#2). Secure it with one Bracket (#41), two M10 x 2 ¾” Carriage Bolts (#79), ∅ ¾” Washers (#81), and M10 Aircraft Nuts (#84). Do not tighten the Nuts and Bolts yet. B.) Attach the bottom of the Vertical Beam (#3) to the Main Base Frame (#1). Secure it with two M10 x 3 ½” Carriage Bolts (#77), ∅ ¾” Washers (#81), and M10 Aircraft Nuts (#84). Do not tighten the Nuts and Bolts yet. C.) Attach the Butterfly S
Краткое содержание страницы № 7
STEP 3 (See Diagram 3) A.) Attach the Left and Right Front Presses (#6 & 7) to the pivot on the Main Base Frame (#1). Secure them together with a M10 x 8 1/8” Axle (#38), two ∅ ¾” Washers (#81), and two M10 Aircraft Nuts (#84). B.) Attach the Front Press Bracket (#15) to the Front Presses. Secure it with two M10 x 3 1/8” Carriage Bolts (#78), ∅ ¾” Washers (#81), and M10 Aircraft Nuts (#84). C.) Attach the Seat Pad (#30) to the Seat Incline Adjustment (#12). Secure it with two M8 x 1
Краткое содержание страницы № 8
STEP 4 (See Diagram 4) A.) Slide one Butterfly Support Bracket (#10) onto the Right Butterfly (#9). Insert the Right Butterfly into the pivot on the Butterfly Support Frame (#13) from the bottom. Secure it with one ∅ 1 ½” Washer (#21), ∅1 3/8” Lock Ring (#57), M6 x 1 5/8” Hex Bolt (#76), and M6 Aircraft Nut (#85). B.) Attach the Butterfly Arm Pad (#34) to the Right Butterfly. Secure it with two M8 x 2 ¾” Allen Bolts (#74) and ∅ 5/8” Washers (#82). C.) Repeat steps A & B above to instal
Краткое содержание страницы № 9
STEP 5 (See Diagram 5) A.) Attach two ∅ 1” x ¼” Bushings (#60) to the pivot on the Leg Developer (#11). Attach the Leg Developer (#11) to the Bracket in front of the Seat. Secure it with one M12 x 3 1/8” Allen Bolt (#67), two ∅ 1” Washers (#80) and one M12 Aircraft Nut (#83). B.) Insert two Foam Roll Tubes (#24) halfway through the holes on the Seat Incline Adjustment (#12) and Leg Developer (#11). Push four Foam Rolls (#62) onto the Tubes from both ends. Plug four ∅ 2 5/8” Foam Rol
Краткое содержание страницы № 10
CABLE LOOP DIAGRAM 9
Краткое содержание страницы № 11
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach the Lat Bar Holder (#16) to the top of Vertical Beam (#3). Secure it with one M10 x 2 ¾” Carriage Bolt (#79), ∅ ¾” Washer (#81), and M10 Aircraft Nut (#84). B.) Attach the 109” Upper Cable (#26) to the top opening on the Vertical Beam. Attach a Pulley (#64) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#68), two ∅ 7/8” Pulley Bushings (#44), and one M10 Aircraft Nut (#84). Make sure the ball stopper on the Cable is undern
Краткое содержание страницы № 12
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach one end of the 77” Butterfly Cable (#28) to the slot on the Right Butterfly Support Bracket (#10). Draw the Cable towards the right open bracket on the Upper Frame (#4). B.) Attach a Pulley (#64) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#69), two ∅ ¾” Washers (#81), and one M10 Aircraft Nut (#84). C.) Draw the Cable over the Pulley and downward. Attach the Cable to a Single Floating Pulley Bracket (#22). Install a
Краткое содержание страницы № 13
STEP 8 (See Diagram 8 & Cable Loop Diagram) A.) Attach the 161” Lower Cable (#27) to the opening on the bottom of the Leg Developer (#11). B.) Attach a Pulley (#64) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#68), two ∅ 7/8” Pulley Bushings (#44), and one M10 Aircraft Nut (#84). C.) Draw the Cable underneath the Pulley towards the back of the machine to the opening on the bottom of the Main Base Frame (#1). Install a Pulley as described in Step B above. D.) Draw the
Краткое содержание страницы № 14
DIAGRAM 8 13
Краткое содержание страницы № 15
STEP 9 (See Diagram 9 & Cable Loop Diagram) A.) Attach the 46” Front Press Cable (#29) to the bracket on the Main Base Frame (#1). Secure the Cable to the bracket with one M10 x 1 1/8” Allen Bolt (#71), two ∅ ¾” Washers (#81), and one M10 Aircraft Nut (#84). DO NOT over tighten the Nut and Bolt. The eyelet on the Cable should be able to rotate on the Bolt. B.) Draw the Cable to the open slot on the Front Press Bracket (#15). Attach a Small Pulley (#63) to the open slot. Secure it with
Краткое содержание страницы № 16
STEP 10 (See Diagram 10) A.) Cover the Weight stack by two Weight Stack Covers (#19). Secure each Weight Stack Cover with two M10 x ¾” Allen Bolts (#72) and ∅ ¾” Washers (#81). B.) Connect the Lat Bar (#17) to the Upper Cable (#26) with two C-clips (#45) and one Short Chain (#40). C.) Connect the Arm Curl Handle (#18) to the Lower Cable (#27) with two C-clips (#45) and one Long Chain (#39). DIAGRAM 10 15
Краткое содержание страницы № 17
PARTS LIST KEY NO. DESCRIPTION Q’ty 51 1” x 2” End Cap 2 1 Main Base Frame 1 52 ∅ 1” Con-shaped End Cap 2 2 Rear Stabilizer 1 53 ∅ 2 5/8” Foam Roll End Cap 4 3 Vertical Beam 1 54 Quick Release Lock Pin 2 4 Upper Frame 1 55 Round Rubber Bumper 2 5 Top Socket Assembly 1 56 Square Rubber Bumper 2 6 Left Front Press 1 57 ∅ 1 3/8” Lock Ring 2 7 Right Front Press 1 58 ∅ 1 ½” Bushing 8 8 Left Butterfly 1 59 ∅ 1” Bushing 6 9 Right Butterfly 1 60 ∅ 1” x ¼” Bushing 2 10
Краткое содержание страницы № 18
MWM Premier Weight Resistant Chart No. of Plates Bench Press Butterfly Lat Pull Leg Developer 1 38 10 20 20 2 49 13.5 30 30 3 60 16.5 40 40 4 71 20 50 50 5 82 23.5 60 60 6 93 26.5 70 70 7 104 30 80 80 8 115 33.5 90 90 9 126 36.5 100 100 10 137 40 110 110 11 148 43 120 120 12 159 46.5 130 130 13 170 50 140 140 14 181 53 150 150 *Each plate weights 10 lbs. *Numbers are approximate. Actual weight may vary. *Value for butterfly is for each arm. 17
Краткое содержание страницы № 19
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Cu
