Руководство по эксплуатации Impex DBR 90

Краткое содержание страницы № 1

NOTE:
Please read all instructions
carefully before using this
product




POWERHOUSE


Bi-Level Dumbbell Rack
Safety Notice

DBR 90
Hardware Identifier

Assembly Instruction

Parts List

Warranty

Ordering Parts



Model
DBR 90


Retain This
Manual for
Reference


06-25-01


IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
OWNER'S
Tel: (800) 999-8899 Fax: (626) 961-9966
MANUAL
www.impex-fitness.com
info@impex-fitne

Краткое содержание страницы № 2

TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE IDENTIFIER.....…....................................................................... 3 ASSEMBLY INSTRUCTIONS........................................................................... 4 EXPLODED DIAGRAM....................................................

Краткое содержание страницы № 3

IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person

Краткое содержание страницы № 4

3

Краткое содержание страницы № 5

ASSEMBLY INSTRUCTION Tools Required to Assemble the Machine: Two Adjustable Wrenches NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the Left Upright Beam (#3) to the Stabilizer (#1). Secure it with a Bracket (#7), four M10 x 3 ¼” Carriage Bolts (#10), ∅ ¾” Washers (#12), and M10 Aircraft Nuts (#13). B.) Repeat the above procedure A to Connect the Right Upright Beam (#2) to the Sta

Краткое содержание страницы № 6

STEP 2 (See Diagram 2) A.) Connect the two Uprights with one Fixed Rack (#4) on the top level. Align the holes then Secure them with two M10 x 2 ¾” Carriage Bolts (#11), ∅ ¾” Washers (#12), and M10 Aircraft Nuts (#13) on each end of the Rack. Do not tighten the nuts and bolts yet. B.) Connect the two Uprights with one Adjustable Rack (#5) on the top level. Align the Rack width by positioning the smallest dumbbell on the rack. Secure the rack with one M10 x 2 ¾” Carriage Bolt (#11),

Краткое содержание страницы № 7

STEP 3 (See Diagram 3) A.) Connect the two Uprights with one Fixed Rack (#4) on the lower level. Align the holes then Secure them with two M10 x 2 ¾” Carriage Bolts (#11), ∅ ¾” Washers (#12), and M10 Aircraft Nuts (#13) on each end of the Rack. Do not tighten the nuts and bolts yet. B.) Connect the two Uprights with one Adjustable Rack (#5) on the lower level. Align the Rack width by positioning the smallest dumbbell on the rack. Secure the rack with one M10 x 2 ¾” Carriage Bolt (#1

Краткое содержание страницы № 8

STEP 4 (See Diagram 4) A.) Insert a Weight Plate Holders (#6) into the hole on the side of the Left Upright Beam. Secure it with a M10 x ¾” Allen Bolt (#9) and ∅ ¾” Washer (#12). B.) Slide an Olympic Sleeve (#16) onto the Holder. Attach a Spring Clip (#14) onto the Holder. C.) Repeat the above two steps to install the other three Posts. DIAGRAM 4 7

Краткое содержание страницы № 9

8

Краткое содержание страницы № 10

Parts list KEY NO. DESCRIPTION Q’ty 1 Stabilizer 2 2 Right Upright Beam 1 3 Left Upright Beam 1 4 Fixed Rack 2 5 Adjustable Rack 2 6 Weight Plate Holder 4 7 Bracket 2 8 Square End Cap 8 9 M10 x ¾” Allen Bolt 4 10 M10 x 3 ¼” Carriage Bolt 8 11 M10 x 2 ¾” Carriage Bolt 12 12 ∅ ¾” Washer 24 13 M10 Aircraft Nut 20 14 Spring Clip 4 15 Cone-shaped End Cap 4 16 Olympic Sleeve 4 9

Краткое содержание страницы № 11

IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Cust