Краткое содержание страницы № 1
1130STE XP
Owner's Manual
Краткое содержание страницы № 2
SAFETY RULES Safe Operation Practices for Snow Throwers IMPORTANT: This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. Do not operate the equipment without wearing ad e - Look for this symbol to point out im- quate winter outer garments. Avoid loose, dangling por tant safety precautions. It means clothing, such as scarves, which can get caught in CAUTION!!! BE COME ALE
Краткое содержание страницы № 3
Do not put hands or feet near or under rotating parts. Do not overload the machine capacity by attempting Keep clear of the discharge opening and front auger to clear snow at too fast a rate. area at all times. Never operate the machine at high transport speeds Exercise extreme caution when op er at ing on or cross- on slippery surfaces. Look behind and use care when ing gravel drives, walks or roads. Stay alert for hidden backing up. hazards or traffi c. Never direct
Краткое содержание страницы № 4
SAFETY RULES ........................................................ 2-3 MAINTENANCE..................................................... 14-15 PRODUCT SPECIFICATIONS...................................... 3 MAINTENANCE SCHEDULE ..................................... 14 CUSTOMER RESPONSIBILITIES................................ 3 SERVICE AND AD JUST MENTS ........................... 16-18 WARRANTY................................................................ 32 STORAGE ..........................
Краткое содержание страницы № 5
ASSEMBLY / PRE-OPERATION Read these instructions and this manu al in its entirety before you attempt to assemble or operate your new snow thrower. Your new snow thrower has been as sem bled at the factory with the excep tion of those parts left unassembled for shipping purposes. All parts such as nuts, washers, bolts, etc., necessary to com plete the as sem bly have been placed in the parts bag. To ensure safe and proper operation of your snow thrower, all parts and hard ware you assemble mu
Краткое содержание страницы № 6
ASSEMBLY / PRE-OPERATION AUGER AUGER TRACTION DRIVE RETAINER CONTROL CONTROL RETAINER CON TROL LEVER SPRING ROD LEVER SPRING TRACTION DRIVE CON TROL ROD AUGER DRIVE CONTROL CONTROL BRACKET BRACKET FIG. 4 FIG. 6 INSTALL AUGER CONTROL ROD (See Figs. 5 and 6) INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD (See Fig. 7) The auger control rod has the short loop on the end of the spring as shown. NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head. 1.
Краткое содержание страницы № 7
ASSEMBLY / PRE-OPERATION INSTALL CHUTE DEFLECTOR REMOTE CONTROL INSTALL WEIGHT BAR (See Fig. 10) (See Figs. 8 and 9) Though seldom required, the weight bar will re duce the 1. Install remote cable bracket to discharge chute with ten den cy of the auger housing to ride up on hard, icy drifts. 5/16-18 carriage bolt, 5/16 fl at washer and 5/16-18 Should conditions require it, install as follows: locknut as shown. Tighten securely. 1. Shut off engine and wait for all moving parts to stop. 2.
Краткое содержание страницы № 8
OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand their meaning. PRIMER DANGER OR WARNING READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS BEFOR
Краткое содержание страницы № 9
OPERATION SPARK ENGINE OIL CAP AUGER DISCHARGE CHUTE CONTROL LEVER PLUG WITH DIPSTICK CONTROL SAFETY LEVER DEFLECTOR REMOTE DRIVE SPEED IGNITION CONTROL LEVER CON TROL LEVER KEY GAS O LINE FILLER CAP TRACTION CHUTE CHOKE DRIVE DE FLEC TOR CON- CONTROL TR OL LEVER FUEL SHUT-OFF VALVE LH TURN TRIGGER THROTTLE / ENGINE CONTROL DISCHARGE LIGHT CHUTE RECOIL POWER (AUXILIARY) CORD STARTER PLUG ELECTRIC HANDLE OIL DRAIN PLUG START HANDLE BUTTON KNOB CLEAN-OUT TOOL PRIM ER MUF FL
Краткое содержание страницы № 10
OPERATION The operation of any snow thrower can result TO USE CHOKE CON TROL (See Fig. 14) in foreign objects thrown into the eyes, which The choke con trol is located on the en gine. Use the choke can result in severe eye damage. Always wear control when ev er you are starting a cold en gine. Do not safety glasses or eye shields while operating use to start a warm en gine. your snow thrower or performing any ad just - To engage choke, turn knob clockwise. Slowly turn ments or repair
Краткое содержание страницы № 11
OPERATION TO MOVE FORWARD AND BACKWARD (See Fig. 18) TO THROW SNOW (See Fig. 16) SELF-PROPELLING, forward and reverse movement of The auger rotation is controlled by the auger control lever located on the right side handle. the snow thrower, is controlled by the traction drive control lever located on the left side handle. Squeeze auger control lever to handle to engage the auger and throw snow. Squeeze traction drive control lever to handle to en gage the drive system. Relea
Краткое содержание страницы № 12
OPERATION When not using drift cutters, loosen adjustment nut, TO ADJUST SKID PLATES (See Fig. 20) lower to storage position and tighten nut securely. NOTE: The wrench provided in your parts bag may be used to adjust the skid plates. BEFORE STARTING THE ENGINE Skid plates are located on each side of the auger housing CHECK ENGINE OIL LEVEL (See Fig. 22) and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height The engine on your
Краткое содержание страницы № 13
OPERATION TO START ENGINE 6. When the engine starts, release the recoil starter han dle and slowly move the choke control to the OFF Be sure fuel shut-off valve is in the OPEN position. position. Your snow thrower engine is equipped with both a 120 Volt Allow the engine to warm up for a few minutes. Engine will A.C. electric starter and a recoil starter. The electric starter not develop full power until it has reached normal operating is equipped with a three-wire power cord and p
Краткое содержание страницы № 14
For extremely heavy snow, re duce the width of snow WARNING: Do not operate snow removal by overlap ping previous path and moving thrower if weather conditions im pair vis- slowly. ibility. Throwing snow dur ing a heavy, Keep engine clean and clear of snow during use. This windy snowstorm can blind you and be will help air fl ow and extend engine life. hazardous to the safe operation of the After snow-throwing is completed, allow engine to run for snow thrower. a few min
Краткое содержание страницы № 15
MAINTENANCE Check the crankcase oil level before starting the engine and SNOW THROWER after each fi ve (5) hours of continuous use. Tighten oil fi ll Always observe safety rules when performing main te nance. cap / dipstick securely each time you check the oil level. TIRES TO CHANGE ENGINE OIL Maintain proper air pressure in both tires (See “PROD- Determine temperature range anticipated before next oil UCT SPECIFICATIONS” section in this manual). change. All oil must meet API service clas
Краткое содержание страницы № 16
SERVICE AND ADJUSTMENTS 1. Disengage all controls and move throttle control to WARNING: To avoid serious injury, STOP position. Wait for all moving parts to stop. before performing any service or ad- 2. Disconnect spark plug wire from spark plug and place just ments: wire where it cannot come in contact with plug. 1. Be sure throttle is in STOP position. 3. Align holes in impeller hub with holes in impeller shaft 2. Remove safety ignition key. and install two (2) new 1/4-20 x 1-5/8" c
Краткое содержание страницы № 17
SERVICE AND ADJUSTMENTS TO REPLACE BELTS (See Fig. 25) The auger and traction drive belts are not adjustable. If the HINT: Insert a 3/8" drive ratchet (in the “ON” position) into belts are damaged or begin to slip from wear, they should the square hole in idler arm and rotate ratchet clockwise be replaced. It is recommended that the belt(s) be replaced to relieve tension. by a qualifi ed service center. 8. With tension relieved on idler, install new traction drive belt around pulleys and ins
Краткое содержание страницы № 18
TO REMOVE WHEELS (See Fig. 26) NOTE: To seal punctures or prevent fl at tires due to slow leaks, tire sealant may be purchased from your local parts Remove the klik pin and remove wheel from axle. dealer. Tire sealant also prevents tire dry rot and cor ro sion. IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the ENGINE hole in the wheel hub (if equipped). Inner hole in axle and See engine manual. hole in wheel hub are not used
Краткое содержание страницы № 19
TROUBLESHOOTING See appropriate section in manual unless directed to a qualifi ed service center. PROBLEM CAUSE CORRECTION Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key.
Краткое содержание страницы № 20
REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLY SNOW THROWER - MODEL NO. 1130STE XP (HU1130STC), PRODUCT NO. 954 22 30-81 48 51 49 33 35 47 32 36 19 34 37 27 44 43 45 42 38 50 27 43 46 41 42 40 39 16 14 4 13 6 52 15 6 54 6 12 20 21 6 5 23 9 53 19 7 7 24 25 55 54 19 18 28 26 8 19 20 21 10 29 55 23 25 6 19 24 28 11 27 24 31 27 52 23 20 25 54 3 19 1 53 30 21 26 18 2 54 25 19 24 23 20 21 22 20
