Краткое содержание страницы № 1
English Español
For Your Records and
Warranty Assistance
T T Type 2 Models ype 2 Models ype 2 Models
For reference, also attach your receipt or a copy
of your receipt to the manual.
Owner’s Guide and Installation Manual
Norway
__________________________________________
Model Name
20490
__________________________________________
Model No.
__________________________________________
Date Purchased
__________________________________________
Where Purchased
Form# 45025-01
20090224
©2009 Hunter Fan Co
Краткое содержание страницы № 2
Welcome Your new Hunter ceiling fan is an addition to your home or office that ® will provide comfort and performance for many years. This installation and operation manual gives you complete instructions for installing and operating your fan. We are proud of our work. We appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world. Before installing your fan, for your records and warranty assistance, record information from the carton and Hunter namepl
Краткое содержание страницы № 3
I In ns st ta al ll le er r’’s C s Ch hoi oic ce a e an nd O d Opt pti io on na al A l Ac cc ce es ss so or ri ie es s Understanding Mounting and Installer’s Choice® Support Brace Hunter’s patented 2-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of two ways, depending on ceiling height and your preference: Standard or Angled mounting. The steps in this manual include instructions for Ceiling Standard both Installer’s
Краткое содержание страницы № 4
1 • Getting Ready To install a ceiling fan, be sure you can do the following: • Locate the ceiling joist or other suitable support in ceiling. • Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: • Electric drill with 9/64” bit • Standard screwdriver (magne
Краткое содержание страницы № 5
2 • Installing the Hanger Bracket 2-1. Drill two pilot holes into the wood support structure through the outermost holes in the outlet box. The pilot holes should be 9/64” Isolator in diameter. Hanger Note: Your fan comes with four pre-installed neoprene noise Bracket isolators. 2-2. Thread the lead wires from the outlet box down through the hole in the middle of the hanger bracket. 2-3. Align the slotted holes in the hanger bracket with the pilot holes you drilled in the wood support s
Краткое содержание страницы № 6
3 • Assembling and Hanging the Fan 3-1. To assemble fan to hang down from a flat or angled ceiling, place Steps 3-1 – 3-3 the canopy and canopy trim ring around the adapter so that they rest on the fan assembly. Downrod 3-2. Feed the wires from the fan through the downrod. Note: Make sure all the wires are on the same side of the metal Canopy dowel pin inside the dowrod. 3-3. Using the provided Allen wrench, loosen the setscrew on the adapter to install the pipe and ball assembly. Note:
Краткое содержание страницы № 7
4 •Wiring the Fan All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician. Wall switches are not included. Select an acceptable general-use switch in accordance with national and local electrical codes. 4-1. Before attempting installation, make sure the power is still off. 4-2. To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise u
Краткое содержание страницы № 8
5 • Installing the Canopy and Canopy Trim Ring Steps 5-1 – 5-2 Hanger Bracket 5-1. Partially install two canopy screws (about 2 full turns) in the hanger bracket. 5-2. Raise the canopy over the hanger bracket. Align partially installed screws with key slots in canopy. 5-3. Twist canopy clockwise to secure. 5-4. Install third & fourth canopy screw in round hole on canopy. Securely tighten all four screws. Canopy Trim Ring Canopy 5-5. Using both hands, push the canopy trim ring up to the t
Краткое содержание страницы № 9
6 • Assembling the Blades 6-1. Attach each blade to a blade iron using three blade assembly screws. Step 6-1 Blade Assembly Screws Blade Assembly Screw 9 45025-01 • 02/24/09 • Hunter Fan Company
Краткое содержание страницы № 10
7 • Completing Your Installation With a Bowl Light Fixture 7-1. To attach the lower switch housing, connect the upper plug connector from the motor to the lower plug connector in the lower switch housing assembly. Note: Both plug connectors are polarized and will only fit together one way. Make sure the connectors are properly aligned before connecting them. Incorrect connection could cause improper operation and damage to the product. 7-2. Place the lower switch housing assembly over th
Краткое содержание страницы № 11
7 • Completing Your Installation With a Bowl Light Fixture Installing the Glass Bowl 7-3. First install B10 candelabra bulbs (40 Watt Maximum) into the sockets. 7-4. Thread the pull chains through the holes in the metal disc. Then, thread the pull chains through the hole in the center of the glass bowl. 7-5. Thread the pull chains through the Light Bulbs grommet holes on the sides of the cover (B10 Metal Disc plate. Candelabra Threaded Base 40 Watt 7-6. Place the cover plate up agai
Краткое содержание страницы № 12
8 • Operating and Cleaning Your Ceiling Fan 8-1. Turn on electrical power to the fan. 8-2. The fan pull chain controls power to the fan. The pull chain has four settings in sequence: High, Medium, Low and Off. • Pull the chain slowly to change settings. • Release slowly to prevent the chain from recoiling into the blades. • The chain uses a breakaway connector that separates if the chain is jerked. If this happens, simply reinsert the chain into the connector. 8-3. The light pull chain contr
Краткое содержание страницы № 13
9 • Troubleshooting Problem: Nothing happens; fan does not move. 1. Turn power on, replace fuse, or reset breaker. 2. Loosen canopy, check all connections according to the wiring the fan section. 3. Check the plug connection in the switch housing. 4. Push motor reversing switch firmly left or right to ensure that the switch is engaged. 5. Pull the pull chain to ensure it is on. 6. Remove the shipping bumpers. Problem: Noisy operation. 1. Tighten the blade assembly screws and blade iron armat
