Руководство по эксплуатации Harbor Freight Tools CENTRAL PNEUMATIC 94847

Краткое содержание страницы № 1

PNEUMATIC PLANISHING HAMMER
94847
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may
differ slightly from the product described herein.
®
Distributed Exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
Copyright © 2006 by Harbor Freight Tools . All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the

Краткое содержание страницы № 2

Specifications Speed 875 - 1350 BPM Operating Air Pressure 50 to 100 (maximum) PSI; 4 SCFM Air Inlet 1/4”, 18 NPT, female Overall Dimensions 23 (L) x 5-1/2 (W) x 24 (H) inches (C-frame and Hammer) Anvil-to-Hammer Opening 4 inches (maximum) Anvil Height Adjustment 2-position anvil shaft mount with lock pin 3/8” to 1-1/4” opening (between head and anvil); 4- position, stepped anvil micro-adjustment block 1/16” height difference between each level Anvil Sizes 1” Radius, 2” Radius and 3” Radius Th

Краткое содержание страницы № 3

8. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines. 9. Maintain tools with care. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and, if damaged, have them repaired by an authorized technician. The handles must be kept clean, dry, and free from oil and grease at all times. 10. Disconnect air supply. Unplug tool from air sup

Краткое содержание страницы № 4

Unpacking When unpacking, check to make sure the following parts are included. Refer to the Parts List and Assembly Drawing located at the end of this manual. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Regulator (11) Air Hammer (10) Screw (2) Hammer Head (3) Anvil (5) Adjustable Pole (7) Air Hose (12) Stopper Pin (9) Range Adjust Block (6) Switch Assembly (13) Mounting Holes (Qty. 4) Installation Mounting

Краткое содержание страницы № 5

Caution: Do not turn on the Air Compressor at this time. Oiler and Filter Connection Dirt, water, and the lack of pneumatic tool oil are major causes for tool wear. Install an optional oiler-filter (not supplied), as illustrated below for better performance. Connect the air tool, air hoses, filter, and oiler to the Compressor Air Outlet as illustrated below. Use pipe thread seal or Teflon tape on all threaded connections. The filter and oiler (not supplied) are recommended but not mandator

Краткое содержание страницы № 6

Operation 1. To change the height of the Anvil (5) to within 1-1/2 inches of the desired height, pull out Stopper Pin (9), and move the Adjustable Pole (7) up or down to one of two Stopper Pin holes. Replace Stopper Pin. 2. To adjust closer to the desired height, move the Range Adjust Block (6) to the right or left to reach the desired height. 3. Turn on the Air Compressor and set its regulator to 90 PSI. 4. Before planishing, test the operation by pressing down on the foot Switch Assy (13)

Краткое содержание страницы № 7

Maintenance 1. After each use, wipe all components of the Planishing Hammer with a clean cloth to remove any dirt and grease buildup. 2. To maintain tool life, always lubricate the air line by adding a few drops of pneumatic tool oil to the air line (or Air Inlet) before each use. Or, install the automatic oiler-filter system as illustrated on page 5. 3. Before each use, drain water out of the air compressor tank and condensation from the air lines. Refer to the Air Compressor Operation Manu

Краткое содержание страницы № 8

Assembly Drawing Page 8 SKU 94847 For technical questions, please call 1-800-444-3353

Краткое содержание страницы № 9

LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installatio